Airframe Electrical What are the three connector contact densities?

Q: Airframe Electrical What are the two requirements for a properly formed contact/conductor crimp?

A: A good quality of crimp is always desired in an electrical system.  Good Crimping is always gas-…

Q: what are some vital parameters to be considered when siting a consumer unit/distribution board.

A:

Q: Explain the major consideration required for a protective system.

A: In the power plant, the generator is one of the most expensive pieces of equipment; therefore,…

Q: Why is it important, when soldering connectors onto a piece of electronic circuitry, to leave no…

A: Given: Soldering of connectors

Q: 13. Which of the following is a method for identifying a grounding terminal for connecting an…

A: Based on the power system protection

Q: What is the most important rule of electrical safety?

A: In this question we will write most important rule of electrical safety...

Q: mounting and positioning of switch board khn h?

A: Electricity is safely distributed throughout commercial and industrial buildings using switchboards.…

Q: 4. Write all the types of connectors use in optical fiber cable?

A: The connectors mechanically couple and align the cores of fibers so light can pass.

Q: 10.C-Which part of the NEC standard proposes the switches requirements?   D-If the branch circuits…

A: The Given General living space is

Q: Why are ac contactor assemblies made of laminated steel

A: The three necessary mechanisms of operation of magnetic contactor are horizontal-action, bell crank,…

Q: Discuss any two types of grounding methods.

A: Two types of grounding methods: Solid grounding Resistance grounding

Q: What devices are used to do the testing of a Coaxial Cable? Write the procedure used to test if a…

A: A coaxial cable, commonly known as coax, is an electrical cable that consists of an inner conductor…

Q: What are the specific functions of a ground wire, a fuse, or a circuit breaker , and a double…

A: The main function of a ground wire is to pave a path for high currents that occur due to faults in a…

Q: Diagram

A:

Q: 4. Why is less overshoot desired for practical systems?

A: Overshoot: It is the manifestation of a function or signal that exceeds its target.

Q: Compare switch types (IGBT, Thyristor, MOSFET, Power Transistor, GTO) in terms of switch frequency,…

A: IGBT , MOSFET , thyristor , Power transistor, GTO have different characteristics. Depending on the…

Q: 19. i. Draw the block diagram of a solar Photo-Voltaic system with the stand by diesel generator and…

A: There are different sources and types of energy present. They can be renewable and non-renewable…

Q: Airframe electrical What are three connector coupling mechanisms that a connector could employ?

A: Threaded coupling, bayonet coupling, and clips couplings are three connector coupling mechanism that…

Q: Explain what is the Wiring Diagram of Direct On Line Starter based on your understanding.

A: DOL starter- A DOL starter (direct on line) is the standard method of starting a small single or…

Q: Why is electrical safety very important at home and at the school or workplace?

A: The flow of electrons within a conductor produces electric current. The flow of electric current is…

Q: Airframe Electrical What are the benefits of using connectors in aircraft wiring?

A: Aircraft carries a heavy and very expensive circuit and machine through it.These circuits and…

Q: Explain bus bar and bus bar chamber

A: In this question we will write about bus bar and bus bar chamber....

Q: While discussing armature testing: Technician A says to test for shorts, place the ohmmeter leads on…

A:

Q: Write specifications details of all types of wiring/ cables

A: Electrical wiring A method of connecting different accessories for electrical energy distribution…

Q: () Discuss the cascade control scheme for a heat exchanger system with a neat diagram. (i) List down…

A:

Q: nmc cable is run through a floor it must be protected by at least how many inches of

A: To find the minimum distance of protection in inches of NM cable when it run through floor.

Q: Why is proper grounding important?

A: Ground potential:  Ground potential has zero reference level used in a system to measure and apply…

Q: 5. Explain the advantages and disadvantages of various types of grounding and indicate where each…

A: The system earthing refers to the earthing of the transformer and generator's neutral points. A…

Q: Explain mounting arrangement and positioning of switch boards

A: According to Siemens switch boards instruction and installation guide, •Extreme care should be taken…

Q: What is bus bar in electrical?

A: The bus bar in the electrical system is known as the conductor or the bunch of conductor which is…

Q: draw mounting arrangement  of distribution board and main switch

A: It is asked to draw the mounting arrangement of distribution board and main switch.

Q: Write all the types of connectors use in optical fiber cable?

A: The connectors mechanically couple and align the cores of fibers so that light can pass. Connectors…

Q: In what ways may the Instrusion detection and prevention system be used to reduce the hazards of…

A: Intrusion detection and prevention system is used as no one can enter our system with malicious…

Q: Explain the Wiring Diagram of Direct On Line Starter based on your understanding in a minimum of 100…

A: Direct online starter is used to start a three phase induction motor In this method starter is used…

Q: What is electrical earthing ans its type?

A: Electrical Earthing: It is the phenomenon of discharging the electrical energy immediately into the…

Q: List six things to Cheak as part of routine preventive maintenance for large contactor

A: As part of routine preventive maintenance for large contactors, the large contactors should be…

Q: Airframe Electrical What is the purpose of the inspection hole on a connector contact?

A: There are different kind of connectors. Crimped contacts are mostly used connectors.Connectors are…

Q: Define contactor

A:

Q: Why the protective device coordination is important in electrical power system?

A: Since fault current is very high compare to rated current.so if we does not clear the fault sudden…

Q: Airframe Electrical What is the strength requirement of a properly crimped contact?

A: strength requirement of a properly crimped contact should be equal or greater than the tensile…

Q: Airframe Electrical How much of the conductor should be exposed past the end of properly crimped…

A: Crimped contact is used to provide maximum reliability and safety to electrical equipment.There are…

Q: 26a)Select suitable material for sole electric plug and explain the selection procedure for…

A: Sutable material sole electric plug- Overheating: the pins must not get too hot, or there will be…

Q: what is the most common control voltage use in intrinsically safe system?

A: Intrinsic safety is the method of protection for control and instrumentation circuits where the…