Airframe electrical What are three connector coupling mechanisms that a connector could employ?

Q: PVC bends must be made so that the conduit remains undamaged and the internal diameter of the…

A: Bends shall be so made that the conduit will not be damaged and the internal diameter of the…

Q: In terminating the coaxial cable, if the present procedure is to cut part of the braided shield and…

A: In this question we need to find what is the next procedure is to

Q: 8. What are the two necessary condition for a thyristor to begin conduction? 9. Define holding…

A: Thyristor is a p-n-p-n, four layers, three junctions semiconductor switching device. It has three…

Q: if a wired connector has a marking of AL/CU on it; what types of conductor can be used with that…

A:

Q: A long, inexpensive extension cord is connected from inside the house to a refrigerator outside. The…

A: The resistance of the extension cord depends on, R=ρlA Here, ρ is the resistivity of the cord, lis…

Q: 4. Write all the types of connectors use in optical fiber cable?

A: The connectors mechanically couple and align the cores of fibers so light can pass.

Q: 10.C-Which part of the NEC standard proposes the switches requirements?   D-If the branch circuits…

A: The Given General living space is

Q: Why are ac contactor assemblies made of laminated steel

A: The three necessary mechanisms of operation of magnetic contactor are horizontal-action, bell crank,…

Q: Discuss any two types of grounding methods.

A: Two types of grounding methods: Solid grounding Resistance grounding

Q: What devices are used to do the testing of a Coaxial Cable? Write the procedure used to test if a…

A: A coaxial cable, commonly known as coax, is an electrical cable that consists of an inner conductor…

Q: Airframe Electrical System Question: In general, what factors areconsidered when selecting the…

A: While manufacturing, the sizes of the wire are selected according to a known standard called as…

Q: A switch is required to switch two speakers from being in series to being in parallel. a) What type…

A: PART A & B The requirement here is to convert two speakers which are connected in series to a…

Q: Explain what is the Wiring Diagram of Direct On Line Starter based on your understanding.

A: DOL starter- A DOL starter (direct on line) is the standard method of starting a small single or…

Q: What is switch?

A: On the basis of number of pole and throw switch can be  1)SPST: Single pole single throw 1)SPDT:…

Q: Airframe Electrical What are the benefits of using connectors in aircraft wiring?

A: Aircraft carries a heavy and very expensive circuit and machine through it.These circuits and…

Q: Explain safe work practice requirements for Non-Electrical Workers?

A: Electricity is a form of energy which arises due to flow of electrical power or charge. It is a…

Q: While discussing armature testing: Technician A says to test for shorts, place the ohmmeter leads on…

A:

Q: What happens if the additional resistance is added in series with armature?

A: The reason behind adding the resistance in series with the armature is discussed below:

Q: What screw size is use to secure a lighting outlet ?

A:

Q: How does the Zener impedance affect the voltage across the terminals of the device?

A: BJT and MOSFET are the class of transistors used in analog electronics. They are widely used…

Q: True or False: If the commutator and brushes must be made of different materials, the commutator and…

A: In this question we will write material used for commutator and brushes in dc machine....

Q: () Discuss the cascade control scheme for a heat exchanger system with a neat diagram. (i) List down…

A:

Q: 5. Explain the advantages and disadvantages of various types of grounding and indicate where each…

A: The system earthing refers to the earthing of the transformer and generator's neutral points. A…

Q: What does a compatible load mean? What if the load is not compatible?

A: This question is from "Power system and protection". Under which we are going to study load…

Q: what does interlocking do?

A:

Q: What is the electrical-resistance strain gage?

A: The electrical resistance strain gage is as follows: - Electrical resistance strain gages are…

Q: Explain mounting arrangement and positioning of switch boards

A: According to Siemens switch boards instruction and installation guide, •Extreme care should be taken…

Q: What is the benefit of soldering when you do it correctly?

A: Soldering is a metal-to-metal connecting procedure in which solder is melted and then used to…

Q: Write all the types of connectors use in optical fiber cable?

A: The connectors mechanically couple and align the cores of fibers so that light can pass. Connectors…

Q: Airframe Electrical What are the three connector contact densities?

A: Electrical connector is a device which is used to connect conductors of different wires. Electrical…

Q: In what ways may the Instrusion detection and prevention system be used to reduce the hazards of…

A: Intrusion detection and prevention system is used as no one can enter our system with malicious…

Q: how do we calculate the clearance distance in high voltage ? is clearance and arcing distance the…

A: Clearance distance:

Q: 18. What are the types of fuses in common use?

A: Fuses in common use

Q: 17. Which of the following can be used to bond the metal parts at services? A. Ground clamps B.…

A: Note- According to our policy, we can answer only one question, please post other question as…

Q: 7. An attachment plug establishes connection between ____.

A: An attachment plug is electrical device.it is used to make connection by inserting in receptacle.

Q: List the basic concepts involved in house wiring?

A: Some of the basic concepts related to home wiring are mentioned below, At the time of wiring, all…

Q: What is meant by a 4-wire 3-∅ system? What advantage does it possess

A: In this question we will write about 3 phase 4 wire system....

Q: Airframe Electrical What is the strength requirement of a properly crimped contact?

A: strength requirement of a properly crimped contact should be equal or greater than the tensile…

Q: What is the difference between bounding and grounding?

A: The difference between bounding and grounding is given below: 1) Bonding is the lasting joining of…

Q: Explain the concept of “grounding”

A: The neutral points of the transformer and generator are earthed as part of the system earthing. When…

Q: Explain how LVDT can be used for the measurement of displacement.

A: LVDT can be used for the measurement of displacement.