An 11 000 V/230 V, 50 Hz, single-phase, core-type transformer has a core section 25 cm x 25 cm. Allowing for a space factor of 0.9, find a suitable number of primary and secondary turns, if the flux density is not to exceed 1.2 T.

An 11 000 V/230 V, 50 Hz, single-phase, core-type transformer has a core section 25 cm x 25 cm. Allowing for a space factor of 0.9, find a suitable number of primary and secondary turns, if the flux density is not to exceed 1.2 T.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.28MCQ

See similar textbooks

Related questions

Q: Example 4.3 A single phase transformer is connected to a 540V, 50HZ ac supply. The transformer has…

A: Given :Primary voltage, E1=540 Vfrequency, f=50 HzPrimary turns, N1=800 turnsSecondary turns,…

Q: A 500 kVA, 6600/440 V, 50 Hz single phase core- type power transformer has maximum flux density of…

A: Given values are - Maximum Flux densityBm=1.5Wbm2Induced voltage per turnEN=30VFrequencyf=50Hz

Q: A 800/170V, 50 HZ, 1-phase transformer with cross sectional area of the core is 24 cm? and maximum…

Q: A 800/160V, 55 HZ, 1-phase transformer with cross sectional area of the core is 26 cm? and maximum…

Q: A 5000 V / 320 V, 50HZ single-phase transformer is to have an approximate e.m.f. per turn of 25 V…

Q: A single-phase transformer has 500 turns on the primary and 100 turns on the secondary. The mean…

Q: Figure Q1 shows a transformer core that has the primary winding (Np) of 500 turns and second winding…

Q: Assignment 2 A 60-Hz 20-kVA 2400/240-V-rms transformer has the following equivalent-circuit…

A: Given f=60 HzV1=2400V2=240 Calculating transformer ratio a=V1V2a=2400240a=10

Q: b) Calculate the transformer core area that is required to limit the core flux density to 1.75T,…

A: We need to find area of given transformer

Q: Determine the number of turns of the primary and the secondary windings of a 60 Hz, 240/120 V ideal…

A: We have an transformer with, Primary Voltage (v1) = 240 V Secondary Voltage (V2) = 120 V Flux (ϕm) =…

Q: Figure Q1 shows a transformer core that has the primary winding (Np) of 500 turns and second winding…

A: A transformer core is shown with dimensions. Number of turns in the primary winding and secondary…

Q: The hysteresis coefficient of the core material of a power transformer is 110J/ m3. The eddy current…

Q: Maximum flux density in the core of 225 V/3000 V, 50 Hz single-phase transformer is 1.3 Wb/m?, If…

A: Given: A 225 V/3000 V, 50 Hz single phase transformer has, Maximum flux density = 1.3 Wbm2 EMF per…

Q: A single-phase transformer has 480 turns on the primary and 90 turns on the secondary. The mean…

Q: A single phase, 60 Hz ,1000 kVA transformer for 14000 / 200V ratio has a maximum flux density of 2.0…

A: In this question, we need to determine the inductance of the winding if Magnetizing current Im =…

Q: Q.1: The following data refer to a single-phase transformer: Turn ratio (1:5), R1=0.24 n, X=1 N,…

Q: The voltage per winding of the 220V/12V, 60 Hz single phase core transformer is 1V. If the maximum…

Q: a) State Faraday's Law for a transformer and prove the equation for the R.M.S. voltage across the…

Q: A core centres = 0.2 m, Height of window = 0.24 m Diameter of circumscribing circle = 0.14 m. The…

Q: A core type transformer operates on 400 / 230 volt, 55 Hz supply. If the cross-sectional area of the…

Q: A transformer takes a No load current of 0.29 A and power factor of 0.405 lag, when its primary is…

A: Given, No load current (Io)= 0.29 A No load power factor= 0.405 lagging No load supply voltage…

Q: A 60HZ transformer having a 480 turn primary winding takes 80 W in power and 1.4 A in current at an…

A: No load power factor=power at noloadvoltage×current. EMF =4.44 frequency ×flux×primary turns.

Q: A power transformer has 1000 primary turns and 100 secondary turns. The cross-sectioal area of the…

Q: Calculate the core-area required for a 1600 kVA, 6600/440 V, 50 Hz, siogle- phase core-type power…

A: In this question we need to find the core area of Transformer.

Q: An 11 000 V/230 V, 50 Hz, single-phase, core-type transformer has a core section 25 cm × 25 cm.…

Q: Explain why the efficiency of a transformer which supplies a pure capacitive load is zero.

A: The efficiency of transformer is calculated by PoutputPinput*100% The output of a transformer is…

Q: A single phase transformer operates at 50 Hz, 200 V rms power supply. Find the number of turns in…

A: This question belongs to electrical machine . It is related to single phase transformer . It is…

Q: 7. The following data were obtained when a 25 kVA, 2300/460 V, 50 Hz transformer was subjected to…

Q: A 10 transformer has 500 primary and 1200 secondary turns. The net cross-sectional area of the core…

Q: A single phase 200V/1005V, 53Hz transformer has a net core area of 0.050 m2 and the maximum flux…

Q: Question- The net cross-sectional area of a single-phase, 50 Hz transformer is 500 cm? having 400…

A: The specifications of the transformer are given as:

Q: When conducting no-load test on a given single- phase transformer, the following test data were…

A: Need to find core loss and currents for given transformer

Q: Calculate the core and window areas required for a 1100 kVA, 6600/400 V, 50 Hz, single pahse core…

Q: the no load current I0 is in phase with the magnetic flux

Q: The design requirements of an 11 000 V/400 V, 50 Hz, single-phase, core-type transformer are:…

Q: When conducting no-load test on a given single-phase transformer, the following test data were…

A: In this question , we will find no load equivalent parameters...Core loss current , magnetizing…

Q: Single phase transformer has transformation ratio 6600/250 , 50 hertz, N2 =50. find maximum magnetic…

Q: The maximum flux density in the core of a 250/3000V, 50Hz single phase transformer is 1.2 Wb/m2 . If…

Q: A 3-phase, 50 Hz, oil cooled core type transformer has the following dimensions: distance between…

Q: 4. A single-phase, 50 Hz transformer has 25 primary turns and 300 secondary turns. The…

Q: 1- A 1-phase transformer has 400 primary and 1000 secondary turns. The net cross- sectional area of…

Q: In a transformer, the loss that remains constant with irrespective of load is O Friction and Windage…

A: Let us approach tmat the correct answer by disseminating each of the wrong answer. In this question…

Q: The eddy current and hystresis losses in a 400V, 50HZ, single phase transformer is 500W and 900W…

A: TRANSFORMER: The transformer transfers power from one circuit to another circuit without a change…

Q: distribution transformer is connected to a 2,300 V, 60 Hz ac source with its primary windings equal…

A: In this question we will find mutual flux, maximum flux density etc..

Q: A small single phase transformer has 10.2 watts no-load loss. The core has a volume of 750 cu. cm.…

A: Given, Input Power Pin=10.2 Watt, Core Volume V=750 Cu. cm, Flux density Bm =10000 gauss, Hysteresis…

Q: A single phase transformer has 350 primary and socondray 1050 turns. The primary is connected to 400…

Q: 2.) Apply the core concepts of Faraday's law to solve the following questions a) State Faraday's Law…

A: We have given the following problem

Q: 4. A single-phase, 50 Hz transformer has 25 primary turns and 300 secondary turns The…

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

An 11 000 V/230 V, 50 Hz, single-phase, core-type transformer has a core section 25 cm x 25 cm.
Allowing for a space factor of 0.9, find a suitable number of primary and secondary turns, if the
flux density is not to exceed 1.2 T.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An ideal transformer has no real or reactive power loss. (a) True (b) False
For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
For an ideal transformer, the efficiency is (a) 0 (b) 100 (c) 50
A 23/230-kV step-up transformer feeds a three-phase transmission line, which in turn supplies a 150-MVA,0.8 lagging power factor load through a step-down 230/23-kV transformer. The impedance of the line and transformers at 230kVis18+j60. Determine the tap setting for each transformer to maintain the voltage at the load at 23 kV.
A two-winding single-phase transformer rated 60kVA,240/1200V,60Hz, has an efficiency of 0.96 when operated at rated load, 0.8 power factor lagging. This transformer is to be utilized as a 1440/1200-V step-down autotransformer in a power distribution system. (a) Find the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the ratings as a two-winding transformer. Assume an ideal transformer. (b) Determine the efficiency of the autotransformer with the kVA loading of part (a) and 0.8 power factor leading.
The ratings of a three-phase three-winding transformer are Primary(1): Y connected 66kV,15MVA Secondary (2): Y connected, 13.2kV,10MVA Tertiary (3): A connected, 2.3kV,5MVA Neglecting winding resistances and exciting current, the per-unit leakage reactances are X12=0.08 on a 15-MVA,66-kV base X13=0.10 on a 15-MVA,66-kV base X23=0.09 on a 10-MVA,13.2-kV base (a) Determine the per-unit reactances X1,X2,X3 of the equivalent circuit on a 15-MVA,66-kV base at the primary terminals. (b) Purely resistive loads of 7.5 MW at 13.2 kV and 5 MW at 2.3kV are connected to the secondary and tertiary sides of the transformer, respectively. Draw the per- unit impedance diagram, showing the per-unit impedances on a 15-MVA,66-kV base at the primary terminals.
(a) An ideal single-phase two-winding transformer with turns ratio at=N1/N2 is connected with a series impedance Z2 across winding 2. If one wants to replace Z2, with a series impedance Z1 across winding 1 and keep the terminal behavior of the two circuits to be identical, find Z1 in terms of Z2. (b) Would the above result be true if instead of a series impedance there is a shunt impedance? (c) Can one refer a ladder network on the secondary (2) side to the primary (1) side simply by multiplying every impedance byat2 ?
Rework Problem 3.14 if the transformer is delivering rated load at rated secondary voltage and at (a) unity power factor, (b) 0.8 power factor leading. Compare the results with those of Problem 3.14. -
For an ideal 2-winding transformer, an impedance Z2 connected across winding 2 (secondary) is referred to winding 1 (primary) by multiplying Z2 by (a) The turns ratio (N1/N2) (b) The square of the turns ratio (N1/N2)2 (c) The cubed turns ratio (N1/N2)3
Consider Figure 3.4. For an ideal phase-shifting transformer, the imda nce is unchanged when it is referred from one side to the other. (a) True (b) False
For the transformer in Problem 3.10. The open-circuit test with 11.5 kV applied results in a power input of 65 kW and a current of 30 A. Compute the values for GcandBm in siemens referred to the high-voltage winding. Compute the efficiency of the transformer for a load of 10 MW at 0.8 p.f. lagging at rated voltage.