An air-conditioning system shown below has air flowing over tubes carrying Refrigerant 134a. Given the parameters below, ignoring heat transfer at the outer surface of the air conditioner, and neglecting kinetic and potential energy effects, determine at steady state the following: Air P1 =1 bar 1. T=32°C = 305 K (AV) = 50 m/min Refrigerant 134a R-134a P3 = 5 bar X3 = 0.20 R-134a P4 =5 bar T= 20°C Part a.) the mass flow rate of the refrigerant, in kg/min. Part b.) the rate of heat transfer, in kJ/min, between the air and refrigerant. Air 2+P2 = 0.95 bar T= 22°C= 295 K

An air-conditioning system shown below has air flowing over tubes carrying Refrigerant 134a. Given the parameters below, ignoring heat transfer at the outer surface of the air conditioner, and neglecting kinetic and potential energy effects, determine at steady state the following: Air P1 =1 bar 1. T=32°C = 305 K (AV) = 50 m/min Refrigerant 134a R-134a P3 = 5 bar X3 = 0.20 R-134a P4 =5 bar T= 20°C Part a.) the mass flow rate of the refrigerant, in kg/min. Part b.) the rate of heat transfer, in kJ/min, between the air and refrigerant. Air 2+P2 = 0.95 bar T= 22°C= 295 K

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Steams flow steadily through an adiabatic turbine. The inlet conditions of the steam are 10 MPa, 450 degrees Celsius and 80 m/s, and the exit conditions are 10 kPa, 92% quality and 50 m/s. The mass flow rate of steam is 12 kg/s. Determine: a) The change in kinetic energy b) The power output c) The turbine inlet area delta ke=-1.95 kj/kg W out =10.2 MW A in =0.00447 m2
In an adiabatic turbine, this steam flow is 50 kg / s. The power produced by the turbine is 29 MW.Steam enters the turbine with a pressure of 50 bar and a speed of 60 m / s. At the outlet, at a pressure of 0.06 barIt comes out as saturated water with a speed of 130 m / s. Accordingly, the heat lost by the turbine andFind the turbine inlet and outlet temperatures of steam
Define the system to be a container full of steam. If the steam condenses, did the system hae a positive or negative entropy change?
The compressors of a production facility maintain the compressed-air lines at a (gage) pressure of 700 kPa at 1400-m elevation, where the atmospheric pressure is 85.6 kPa. The average temperature of air is 15°C at the compressor inlet and 25°C in the compressed-air lines. The facility operates 4200 h/yr, and the average price of electricity is $0.10/kWh.
23. A 5.2m3 tank contains nitrogen, which is evacuated from 100kPag to a pressure of 98kPagvacuum. Determine the mass of pumped out nitrogen if initially the temperature is 510K and thefinal temperature is 100K.a. 6.3274kg b. 5.8802kg c. 6.4656kg d. 6.2169kg
The compressors of a production facility maintain the compressed-air lines at a (gauge) pressure of 700 kPa at sea level where the atmospheric pressure is 101 kPa. The average temperature of air is 20°C at the compressor inlet and 24°C in the compressed-air lines. The facility operates 4200 hours a year, and the average price of electricity is $0.078/kWh. Taking the compressor efficiency to be 0.8, the motor efficiency to be 0.92, and the discharge coefficient to be 0.65, determine the energy and money saved per year by sealing a leak equivalent to a 3-mm-diameter hole on the compressed-air line.
A single-cylinder reciprocating compressor has a 5% clearance and a bore and stroke of 25 cm x 30 cm, respectively. The compressor operates at 500 RPM. The air enters the cylinder at 27 C and 95 kPa and discharges at 2000 kPa. Ambient air conditions are 101.3 kPa and 27C. If the polytropic exponent n = 1.3 for compression and re-expansion processes, determine the volume of the actual air being delivered by the compressor in m3/hr. And the power required to drive the unit, in kW, if the compressor efficiency is 82%.
In a steady flow apparatus, 135 KJ of work is done on each kg of fluid. The specific volume of the fluid, pressure and speed at the inlet are 0.37 m3/Kg, 600KPa, and 160 m/s. The inlet is 32 m below the floor, and the discharge pipe is at floor level. The discharge conditions are 0.62 m3/kg, 100KPag and 27 m/s. The total heat gained between the inlet and discharge is 9 KJ/Kg of fluid. In the flowing through this apparatus, by how much does the specific internal energy increase or decrease?
A single-cylinder reciprocating compressor has a 5% clearance and a bore and stroke of 25 cm x 30 cm, respectively. The compressor operates at 500 RPM. The air enters the cylinder at 27 C and 95 kPa and discharges at 2000 kPa. Ambient air conditions are 101.3 kPa and 27C. If the polytropic exponent n = 1.3 for compression and re-expansion processes, A.) determine the volume of the actual air being delivered by the compressor in m3/hr. B.) the power required to drive the unit, in kW, if the compressor efficiency is 82%.
38 - Argon is heated at 350 K with a mass flow of 4 kg/s as it passes through a pipe. Given that the heat taken by the argon is 39 kW and the flow is known to be continuous, which of the following is the temperature at the pipe outlet? (Cp = 0.5203 kJ/kgºC) a) 358.6 ºC B) 95.7 ºC NS) 368.7 ºC D) 85.6 ºC TO) 75.3 ºC
d.a) A single-cylinder reciprocating compressor has a 5% clearance and a bore and stroke of 25 cm x 30 cm, respectively. The compressor operates at 500 RPM. The air enters the cylinder at 27 C and 95 kPa and discharges at 2000 kPa. Ambient air conditions are 101.3 kPa and 27C. If the polytropic exponent n = 1.3 for compression and re-expansion processes, determine the volume of the actual air being delivered by the compressor in m3/hr. a. 233.66 m3/hr b. 323.66 m3/hr c. 212.66 m3/hr d. 263.66 m3/hr For number 2a, the power required to drive the unit, in kW, if the compressor efficiency is 82%. a. -84.62 kW b. -52.62 kW c. -62.84 kW d. -74.84 kW
An adiabatic pump is used to increase the pressure of water from 100 kPa to 500 kPa at a rate of 400 L/min. If the efficiency of the pump is 75 percent, the maximum temperature rise of the water across the pump is (a) 0.096° C (b) 0.058° C (c) 0.035° C (d ) 1.52° C (e) 1.27° C