An LSA is needed to deliver a pulling force of 60 Newtons as part of a larger machine. The parameters of the LSA are - Plunger diameter = 1 cm - Stroke = 1 cm (distance the plunger must travel) - Number of windings on the solenoid = 1200 Part A Determine the current that the LSA requires to operate. You may neglect the reluctance of the iron portions of the actuator along with the reluctance between the plunger and the iron frame. Please enter your answer in Amperes in the space provided. Vη ΑΣφ| vec 20.41241 Submit Previous Answers Reguest Answer X Incorrect; Try Again; 2 attempts remaining Part B If the resistance of each turn of the winding is 0.01 Ohms, compute the voltage that must be applied to the LSA to make it function. Please enter your answer in Volts in the space provided. vec ? V =

An LSA is needed to deliver a pulling force of 60 Newtons as part of a larger machine. The parameters of the LSA are - Plunger diameter = 1 cm - Stroke = 1 cm (distance the plunger must travel) - Number of windings on the solenoid = 1200 Part A Determine the current that the LSA requires to operate. You may neglect the reluctance of the iron portions of the actuator along with the reluctance between the plunger and the iron frame. Please enter your answer in Amperes in the space provided. Vη ΑΣφ| vec 20.41241 Submit Previous Answers Reguest Answer X Incorrect; Try Again; 2 attempts remaining Part B If the resistance of each turn of the winding is 0.01 Ohms, compute the voltage that must be applied to the LSA to make it function. Please enter your answer in Volts in the space provided. vec ? V =

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Suppose we have determined that the lowest natural frequency of a particular helical compression spring is 20286 rpm. According to the prescription in our book and according to the presentation in class, find the highest recommended operating frequency of a machine that utilizes this spring. Give your answer in rpm, but do not include units--Blackboard will not understand
Two identical 2000 kW alternator operates in parallel. The governor of the first machine is such that the frequency drops uniformly from 50 Hz at no-load to 48 Hz at full-load. The corresponding uniform speed drop of the second machine is 50 Hz to 47.5 Hz, What is the maximum load that can be delivered without overloading either machine?
Please give me answer in 45 min. Calculate the minimum technical specifications of a linear pneumatic cylinder that meets the requirements of raising the transfer mechanism in 3 seconds and lowering in 2 seconds.Specifically, the distance to travel (stroke) and diameters.
A punching machine requires 1600 ft-lb of energy to punch a certain hole. During the punching operation, the speed of the machine is reduced from 180 rpm to 160 rpm. The weight of the arms and hub is considered to be 10 % of the rim weight, and the mean diameter of the flywheel is 32 inches. a) What is the mean or operating rpm of the flywheel? b) Find the coefficient of fluctuation. c) What is the maximum speed of the flywheel, in fps? d) What is the minimum speed of the rim, in fps? d) Determine the weight of the rim, in lb. e) What is the weight of the flywheel, in lb? f) Determine the weight of the arms and hub, in lb.
The deflection of a spring with 20 active turns under a load of 1000 N is 10 mm. The spring is made into two pieces each of 10 active coils and placed in parallel under the same load. What is the deflection of this system?
Indicate the differences between the rigid rotor and elastic rotor models, between the frequency of two adjacent lines.
What is the mechanical advantage of the system shown below?
pleassssse solve question 6, statics
Determine the controllability and observability for this system
Aim: To conduct a full kinematic analysis and calculate dynamic reaction forces in a linkage mechanism, calculate instantaneous torque, required to drive the mechanism and to present the results of the case study in a clear reporting format. Introduction: Figure 1 shows a pumpjack operating at an oil well. Its representation as a linkage is also shown in Figure 1. The pumpjack is driven by a motor attached to crank OA. A constant torque T is applied to the crank and the crank rotates at a constant angular velocity ???. A force P is applied vertically downwards at the end of the walking beam BD, which has its centre of mass at point G. To design the mechanism, a careful kinematic analysis of the mechanism needs to be conducted. To avoid mechanical failure and to provide adequate support to the mechanism, the engineer needs to analyse the reaction forces in the joints. Masses of links OA and AB are assumed to be smaller in comparison with the mass of BD and are ignored in the analysis.…
Please answer the following question A cigarettes dispenser requires a south African five-rand (R5) coin with a mass of 9.5 g to dispense one cigarette with a mass of 0.2 g. The design of such a cigarette dispenser is based on a helical spring, of negligible mass, which is found to extend 0.1 mm under a mass of 0.2 g. The spring can support a total mass of a coin. As the customer place money on the dispenser, the spring and coin system displace vertically through 4 mm and release. 1.1. Provide a schematic representation of the mass and spring system. 1.2. Calculate the frequency of natural vibration of the dispenser. 1.3. Determine the velocity of the coin when it is 2 mm below its resting position.
Write the units of coefficient of viscous damping force.