and cross

Q:

A:

Q: Heat transfers Water (T= 10 C, , k=0.644 W/m.C, υ = 5.54× 10^-7 m2/s, Pr=3.55), flow over plate 1m x...

A:

Q: question 2

A: We are to determine the sources of vibration in this assembly

Q: Two solid shafts, 50 mm in diameter, are connected by a flange coupling with six bolts and a pitch ...

A:

Q: 2. The 40mm diameter steel rod AB shown in Figure 2 is resting on frictionless rollers between two s...

A: Given: The diameter of steel rod, d = 40 mm = 0.04 m The length of rod, L = 1500 mm = 1.5 m The gap ...

Q:

A: Note: As per policy, we can solve the first question only from multiple questions. Please resubmit t...

Q:

A:

Q: q3

A:

Q: Q1 (b) Choose the correct answer: The equation of equilibrium, EFx = 0 in the %3D Figure (2) is?

A:

Q: In the figure, torsional moments act on a bar system of abruptly changing cross-section made of the ...

A:

Q: in al cycle, vapor nigh pr temperature of 400 °C and a pressure of 3 MPa and exits at a pressure of ...

A:

Q: A block of mass 20 kg is released from rest at the top of a ramp as shown in Figure 4. Thecoeficient...

A:

Q: On a dial test indicator the stem transfers the movement to the rack, from the rack to compound gear...

A:

Q: Find the specific volume of saturated water vapor that is at 135.3°C in m^3/kg.

A: Given data saturation temperature(Ts )=135.3 oC

Q: Indicates the strength of the bond in the grinding wheel that used on a grinding machine is known as...

A:

Q: Please, explain the physical meaning of the term volume flow rate – determination and

A: For solution refer below images.  

Q:

A: Diameter of the rod, d = 14 mm Original length of the rod, L= 50mm  

Q: The water is flowing through a pipe having diameters 40 cm and 15 cm at sections land 2 respectively...

A: Solution:

Q:

A:

Q: A brass billet is to be extruded from its initial diameter of 100 mm to a final diameter of 50 mm, w...

A: Given: Initial diameter. do= 100 mm or 102 mm Final diameter. d1 = 50 mm  

Q: Fluid machinery

A:

Q:

A:

Q: During the design of the shaft, it is recommended to assume that the radius of the shaft is not stra...

A: In mechanical enegineering,  Torsion is explained as the twisting of a shaft due to an applied torqu...

Q:

A:

Q:

A:

Q: The 150-kg pendulum has a center of mass at G and a radius of gyration about G of kG = 0.25m, as sho...

A:

Q: Compare Wind Energy and Bioma (a) Working Principle (b) Types (c) Advantages (d) Disadvantages le) A...

A: Wind Energy And Biomass Energy

Q:

A: Honeycomb Structure  In composite manufacturing, the honeycomb structure is formed by joining the ce...

Q:

A:

Q: Please help sir (heat transfer)

A:

Q: Find the max coefficient of performance of a Carnot refrigerator operating between the temperatures ...

A:

Q:

A:

Q: Problem #2: A 12-lb model C of the earth is attached to wires AC and BC and revolves at a constant s...

A:

Q:

A:

Q:

A:

Q: The water is flowing through a pipe having diameters 45 cm and 15 cm at sections tand 2 respectively...

A: Given data diameter at section 1 (d1) = 45 cm  diameter at section 2 (d2) = 15 cm  discharge rate (Q...

Q: Hi, Please help me with this question and please show the full solution. Thank you very much

A: The mass flow rate in  a flow section is given by, The repeating variable should be- 1. Be equal in...

Q: The amount of acceleration depends on and which counteracts the acceleration. O a. Angle of inclinat...

A: To fill:- The amount of acceleration depends on.............. and............. Which counteracts the...

Q: ı need solution

A:

Q: Which one of the following options is the reason for lower operating cost of double pipe heat exchan...

A:  double pipe heat exchangers-it has small pipe inside a large pipe concentrically, and all the heat ...

Q:

A:

Q:

A:

Q: Draw three frontal side horizontal projections

A:

Q: Determine the acceleration and time taken by the rolling disc to cover a distance of 91 cmf or the l...

A:

Q: Fluid machinery

A: Given :-  A pump is to discharge 10 m3 sec at a head of 5.0 m when running at 300 rpm. What type of ...

Q: Theory Of machine. Machine Design. Machine Elements.

A:

Q: List the three (3) main reason the usage of Ultrasonic Machining (USM) in modern machining.

A: Ultrasonic machining (USM): It is a type on non-traditional material removal process which removes m...

Q:

A:

Q:

A:

Q:

A: Heat Transfer: According to second law of thermodynamics, heat is always transferred from high tempe...

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.