As shown in the figure below the two planes PQ and QR are having shear stress of 40 MPa. The plane PQ carries the tensile stress of 60 MPa. Find the value of normal and shear stress on the plane PR if the angle between the plane PR and QR is 60°. 40 MPa R 60° 40 MPa 60 MPa P

As shown in the figure below the two planes PQ and QR are having shear stress of 40 MPa. The plane PQ carries the tensile stress of 60 MPa. Find the value of normal and shear stress on the plane PR if the angle between the plane PR and QR is 60°. 40 MPa R 60° 40 MPa 60 MPa P

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.1CTP: EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on...

See similar textbooks

Related questions

Q: b) For the state of plane stress shown in Figure 4, determine: i) the normal and shearing stresses…

A: Note: As value of σy is not given assuming as zero. Given data: σx=-60 MPaσy=0 MPaτxy=20 MPa

Q: The stresses at a point in a bar are o1 = 29 N/mm2 (tensile) and 02= 14N/mm2 (compressive) as shown…

Q: The following stress element represents the stress state at point A of the structure in the figure…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are S, = 75 MPa and 5, =…

A: Given data in question Stresses Angle To find out Normal and shear stress

Q: A rod having a circular cross section (radius; 0.5 in, height; 15 in) is subjected to loadings as in…

A: torque at fixed end T=540 lb.indiameter of shaft d=0.5 inthen shear stress at A abd B…

Q: Figure Q3 (a) shows an overhanging beam ABC subjected to a uniformly distributed load w along AB and…

A: yield stress of the material is 250 MPa

Q: The force p is applied at d=50 mm from the bottom as shown in the figure. Compute the normal stress…

Q: As shown in the figure below the two planes PQ and QR are having shear stress of 40 MPa. The plane…

Q: The state of stress at a point in a body is = 100 MPa. If given by σx = 50 MPa and oy o one of the…

Q: 500 Ib 12 in. P(x,y) 159 mm 600 kN 0 mm 100 mm 150 mm 50 mm 150 nim 3 in. 6 in. 150 mm

Q: 3. Determine the maximum shearing stresses and the associated normal stresses for the state of…

Q: Two planes PQ and QR are having shear stress of 40 MPa. The plane PQ carries the tensile stress of…

Q: A bent rod has a diameter of d=15 mm and is subjected to a force of P= 600 N. What is the normal…

Q: . A cantilever wide-flange beam is loaded by a force P at the free end acting through the centroid…

A: Given Cantilever beam point load acting on its free end Cross section of the beam is I.

Q: Problem Sets - 1: The thin-walled tube is used as a beam to support the uniformly distributed load…

Q: 400 N/mm 45° B. 400 N/mm The square element in the figure is subjected to a biaxial stress of 400…

A: Given data : The value of normal stress in X direction σX=400 N/mm2 The value of normal stress in Y…

Q: The stresses shown act at a point in a stressed body. Normal and shear stress magnitudes acting on…

Q: The bar ABC in the figure consists of two cylindrical segments. The material of the bar has the…

Q: As shown in the figure below the two planes PQ and QR are having shear stress of 40 MPa. The plane…

A: Angle p=300

Q: Problem #2. The state of stress at a point with ox, oy and txy as shown. Analyze the state of stress…

Q: 2. Rods AB and BC have diameters of 4 mm and 6 mm, respectively. If the 3 kN force is applied to the…

A: Draw free body diagram From the above figure, calculate the angle α sinα=35α=sin-10.6α=53.13o

Q: A load of P=1,800 N acts on the machine part shown in the figure. The machine part has a uniform…

Q: -1.2 m m + Wo 2.4 m 200 mm 2 195 mm

A: For the equilibrium of the beam (i) ∑MB =0; (RA x 2.4) - (w0 x 3.6 x 3.6/2) = 0 RA = 2.7w0 N…

Q: The stresses acting on element A in the web of a train rail are found to be ‘75 (MPa)’ tension in…

A: Given,σx=75 Mpaσy=-90 Mpashear stressζ=40 Mpanow,we know that,principle stresses can be determined…

Q: The stresses at a point in a bar are o1 = 28 N/mm2 (tensile) and o2=12N/mm2 (compressive) as shown…

A: In the question angle made by inclined surface with major principle plane is -35 because we have…

Q: In a 2 dimensional stress analysis, the state of stress at a point is shown below in which length of…

Q: As shown in the figure below the two planes PQ and QR are having shear stress of 40 MPa. The plane…

Q: 2 A) Normal and shear stresses acting on horizontal and vertical planes at the point is shown in the…

Q: Part B. Stress 2. Rods AB and BC have diameters of 4 mm and 6 mm, respectively. If the 3 kN force is…

A: Consider the following free body diagram :

Q: As shown in the figure below the two planes PQ and QR are having shear stress of 40 MPa. The plane…

Q: The beam shown in figure 3 is having a cross-section as shown in figure 4. Apply the flexure formula…

A: Draw the shear force and bending moment diagram of the beam as follows. Consider the given section.…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are S, = 85 MPa and S, -…

Q: The state of stress at a point with ox, oy, and txy as shown. Analyze the state of stress at the…

Q: At a point in a stressed material, the major principal stress is 5,000 psf compression and the minor…

A: (a) The diagram for the Mohr’s circle stress combination is shown below.

Q: The following stress element represents the stress state at point A of the structure in the figure…

Q: P1: For the given state of stress, determine (a) the orientation (0) of the planes with the maximum…

A: From the figure, σx=16 ksi, σy=-6 ksi and τxy=-20 ksi (a) The formula to calculate the orientation…

Q: Calculate the value of Q and t that are used in the shear formula for finding the shear stress at A.…

Q: The bar shown in the figure has a square cress section for which the depth and thickness are 40 mm.…

A: Axial force and load on rectangular cross-section = 800 N Cross-section area = 40mm x 40mm Average…

Q: Several torques are applied to the stepped shaft (G concentrations associated with the sudden change…

A: Given :

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

Q: 2. At a point, the major principal stress is 80 psi compression and the minor principal stress is 20…

Q: In a plane stress condition, the components of stress at point are ox = 20 MPa, 0y MPa The maximum…

A: Please refer the attached image for complete solution. THANKYOU.

Q: Q3) the state of plane stress at a point is represented by the element shown below. Determine state…

Q: Determine the average axial tensile stress in the bar of the figure below if P=225 kN and the cross…

A: Given, Axial tensile force P = 225kN P = 225000N Cross sectional area A = 2500 square mm A =…

Q: Rods AB and BC have diameters of 4 mm and 6 mm, respectively. If the 3 kN force is applied to the…

A: Given data:- The diameter for rod AB =4 mm=0.004 m The diameter for rod BC=6mm=0.006 m The applied…

Q: An element in plane stress from the frame of a racing car is oriented at a known angle 0 (see the…

A: As per guidelines we need to answer only first 3 subparts

Q: Consider a point ina structural member that is subjected to plane stress. Normal and shear stresses…

A: As per company policy, we are supposed to answer the first question from the multiple-part question.…

Q: e cross-sectional area. Determine the average normal stress acting at na-a. Show this distribution…

Q: Q#2 Draw the Mohr,s circle for the stress element shown in figure. Determine the principal stresses…

Concept explainers

Asphalt Binders and Mixtures

Asphalt binders are subsidiary products procured during the refining process of petroleum while manufacturing gasoline, diesel, and similar petroleum products. Asphalt binders are obtained from the residue that remains after the distillation of petroleum, this residue is further subjected to steam distillation and oxidation to remove the traces of gas oil present in the residue. Certain additives or modifiers are also added to asphalt binders to alter them to suit different applications.

Question

100%

I need the answer as soon as possible

As shown in the figure below the
two planes PQ and QR are having
shear stress of 40 MPa. The plane
PQ carries the tensile stress of 60
MPa. Find the value of normal and
shear stress on the plane PR if the
angle between the plane PR and
QR is 60°.
40 MPa
R
60°
40 MPa
60 MPa
P

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on the two planes are Plane EB: EB = 25 kN/m2; EB = +10 kN/m2 Plane FG: FG = 10 kN/m2; FG = 5 kN/m2 (Note: Mohrs circle sign conventions for stresses are used above) Given ; = 25, determine: a. The maximum and minimum principal stresses b. The angle between the planes EB and FG c. The external stresses on planes AB and BC that would cause the above internal stresses on planes EB and FG
Determine the maximum normal stress (in Mpa) in bar ABCD if the cross-sectional area of the bar is A = 532 mm2 and P= 35.29 kN. Round off the final answer to four decimal places.
5.2.2 The thin-walled tube is used as a beam to support the uniformly distributed load of intensity w0. (a) Find the largest allowable value of w0 based on the allowable stress in bending of 100 MPa. (b) Compute the corresponding maximum shear stress in the beam.
At a point in a stressed material, the major principal stress is 80 psi compression and the minor principal stress is 20 psi compression. (a) Draw the Mohr’s circle for this stress combination. (b) What is the maximum shear stress acting at the point, and what value of normal stress acts on this same plane? (c) Determine the value of the normal and shear stress acting on a plane that is 60° clockwise (cw) from the minor principal plane.
At a point in a stressed material, the major principal stress is 5,000 psf compression and the minor principal stress is 2,000 psf compression. (a) Draw the Mohr’s circle for this stress combination. (b) Find the maximum shear stress, and also indicate the value of normal stress acting on this same plane. (c) Determine the values of the normal and shear stresses acting on a plane that is 60° ccw from the major principal plane.
1. If P=100kN, and the plate thickness is t=8 mm, determine the maximum axial stress in the structural component shown below.
Determine the magnitude of the maximum in-plane shear stress at point A (in MPa).
refer to the figure due to application of line load q1 and q2 . the vertical stress increase at point a is 42 kn/m2 determine the magnitude of q
11.17:A bending moment of M = 700 N.m is acting on the cross section shown in the figure. Find the largest and smallest stress in the cross section. Answer: ϭmax=5,42 MPa; ϭmin=-2,01 MPa
At a point in a stressed material, the major principal stress is 66 kPa compression and the minor principal stress is 34 kPa tension. (a) Use the Mohr’s circle to determine the shear and normal stress on a plane 45° ccw from the major principal plane. (b) Determine the stress combination acting on the plane 75° ccw from the major principal plane.
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 85 MPa and S, =- 200 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume B= 48°
At a point in a stressed material, the major principal stress is 120 kPa compression and the minor principal stress is 40 kPa compression. (a) Draw the Mohr’s circle for this stress combination. (b) Determine the maximum shear stress. Also indicate the normal stress on the plane where shear is a maximum. (c) Determine the value of normal and shear stress acting on the plane 30° counterclockwise (ccw) from the major principal plane.