Assume an inviscid, incompressible flow. Also, standard sea level density and pressure are 1.23 kg/m3 (0.002377 slug/ft3) and 1.01 × 105 N/m2 (2116 lb/ft2), respectively. The lift on a spinning circular cylinder in a freestream with a velocity of30 m/s and at standard sea level conditions is 6 N/m of span. Calculate thecirculation around the cylinder.

Assume an inviscid, incompressible flow. Also, standard sea level density and pressure are 1.23 kg/m3 (0.002377 slug/ft3) and 1.01 × 105 N/m2 (2116 lb/ft2), respectively. The lift on a spinning circular cylinder in a freestream with a velocity of30 m/s and at standard sea level conditions is 6 N/m of span. Calculate thecirculation around the cylinder.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.29P: Air at 20C flows at 1 m/s between two parallel flat plates spaced 5 cm apart. Estimate the distance...

See similar textbooks

Similar questions

An airfoil is in a freestream where p.(assigned altitude)atm, p(density) (assigned altitude) kg/m3, and V 980 m/s. At a point on the airfoil surface, the pressure is 0.5 atm. Assuming isentropic flow, calculate the velocity at that point. assigned altitude 36.22km
A straight-tapered flying-wing aircraft has the following characteristics: span, 20 ft; area, 100 ft2 ; root chord, 6 ft; tip chord, 4 ft; leading-edge sweep angle, 40 deg; sweep angle of line of maximum thickness, 24 deg; and Airfoil NACA 2412. Determine the wing's lift-curve slope and induced drag k value. Assume the flight Mach number is 0.25 in standard sea-level conditions.
Estimate the annual production of a 12 m diameter horizontal axis wind turbine operating atstandard atmospheric conditions (r = 1.225 kg/m3 ) in an 8 m/s average wind speed regime. speed probality density is given by the Rayleigh density distribution.
A Savonius rotor can be approximatedby the two open half-tubes in Fig mounted ona central axis. If the drag of each tube is similar to thatin Table 7.2, derive an approximate formula for therotation rate Ω, as a function of U, D, L, and the fluidproperties (ρ, μ).
Consider two different flows over geometrically similar airfoil shapes,one airfoil being twice the size of the other. The flow over the smallerairfoil has freestream properties given by T∞ = 200 K, ρ∞ = 1.23 kg/m3,and V∞ = 100 m/s. The flow over the larger airfoil is described byT∞ = 800 K, ρ∞ = 1.739 kg/m3, and V∞ = 200 m/s. Assume thatboth μ and a are proportional to T 1/2. Are the two flows dynamicallysimilar?
Assume an inviscid, incompressible flow. Also, standard sea level density and pressure are 1.23 kg/m3 (0.002377 slug/ft3) and 1.01 × 105 N/m2(2116 lb/ft2), respectively. Consider the flow field over a circular cylinder mounted perpendicular tothe flow in the test section of a low-speed subsonic wind tunnel. Atstandard sea level conditions, if the flow velocity at some region of theflow field exceeds about 250 mi/h, compressibility begins to have an effectin that region. Calculate the velocity of the flow in the test section of thewind tunnel above which compressibility effects begin to become important, i.e., above which we cannot accurately assume totallyincompressible flow over the cylinder for the wind tunnel tests.
Using the irrotational flow approximation, calculate and plot the nondimensional static pressure distribution on the surface of a circular cylinder of radius a in a uniform stream of speed V∞. Discuss the results. The pressure far away from the cylinder is P∞.
Air at 20 °C flows at V = 10 m/s over a flat plate of length L= 1.52 m and width W = 2 m.Calculate the boundary layer thickness at the trailing edge of plate and drag force on one sideof plate if:a. Surface of plate is smooth.b. Surface of plate is rough.The air properties at 20 °C are: Density, ? = 1.2 kg/m3and dynamic viscosity, ? = 1.8x 10-5kg/m·s and kinematic viscosity, ν = 1.516×10-5m2/s. kindly give me the solution of this problem with correct and logical reasoning.
Air at 20 °C flows at V = 10 m/s over a flat plate of length L= 1.52 m and width W = 2 m.Calculate the boundary layer thickness at the trailing edge of plate and drag force on one sideof plate if:a. Surface of plate is smooth.b. Surface of plate is rough.The air properties at 20 °C are: Density, ? = 1.2 kg/m3and dynamic viscosity, ? = 1.8x 10-5kg/m·s and kinematic viscosity, ν = 1.516×10-5m2/s
Air flows through the test section of a small wind tunnel at speed V = 7.5 ft/s. The temperature of the air is 80°F, and the length of the wind tunnel test section is 1.5 ft. Assume that the boundary layer thickness is negligible prior to the start of the test section. Is the boundary layer along the test section wall laminar or turbulent or transitional?From above problem.assume the flow remains laminar, and estimate the boundary layer thickness, the displacement thickness, and the momentum thickness of the boundary layer at the end of the test section. Give your answers in inches, compare the three results, and discuss. .
Estimate the annual production of a 12 m diameter horizontal axis wind turbine operating atstandard atmospheric conditions (r = 1.225 kg/m3 ) in an 8 m/s average wind speed regime. Rayleigh density distribution.
Air at 20 °C flows at V = 10 m/s over a flat plate of length L= 1.52 m and width W = 2 m. Calculate the boundary layer thickness at the trailing edge of plate and drag force on one side of plate if: a. Surface of plate is smooth.b. Surface of plate is rough. The air properties at 20 °C are: Density, ? = 1.2 kg/m3 and dynamic viscosity, ? = 1.8 x 10^-5 kg/m·s and kinematic viscosity, ν = 1.516×10^-5 m2/s.