Assuming that P = 48 000 lb and that it may be applied at any joint on the line FJ, determine the location of P that would cause (a) maximum tension inmember HI; (b) maximum compression in member CI; and (c) maximum tension in member CI. Also determine the magnitude of the indicated force in each case

Q: Set P1 = 6.8 kN , P2 = 8 kN .   Determine the force in the member AB, and state if the member is…

A:

Q: 1. Using Method of Joints, determine the forces in each member and the reaction forces with P = 300…

A: Calculate different angle of the truss:

Q: For the structure given, determine the force acting on each member. (Members AB and BE have lengths…

A: The above structure is analysed using method of joints to find the forces in the members In order to…

Q: Determine the horizontal and vertical components of force which pin C exerts on member ABC. The…

A: The free body diagram is shown below, The moment about point E can be calculated as,

Q: Determine the force in member AB. if P =9.8 kN and L = 4 m Note: Negative if compression and…

A: To Find  Force in member AB of given Truss.

Q: View Policies Current Attempt in Progress Determine the force in each member of the loaded truss.…

A:

Q: Determine the internal force in member DB using trusses properties, if P =12 kN P kN -2 m -2 m E 1.5…

A:

Q: If the bending working stresses are 22.5 ksi in tension and 27 ksi in compression for the beam…

A: Draw the free body diagram. Equilibrium of horizontal forces, ∑Fx=0Ax=0

Q: Load A 3.5 m 45° 45% Load B 45° 45 3.5 m 45 B.

A: Abbreviation used  C = Compression member T = Tension member FAB = force in member AB (similarly for…

Q: B a D F

A:

Q: Determine the force in each member of the loaded truss as a result of the hanging weight W = 170 Ib.…

A: tanθ=36  θ=26.565 tanα=37     α=23.198

Q: roblem 7.5- Determine the force in members KM, LM, and DK using e method of sections. State whether…

A: To find force in member LM,KM,DK

Q: Determine the force in members BC, CD, and CG, if W = 8 kN. Specify whether each member is in…

A: At Joint E : ∑Fy = 0FEG + 8 = 0 ⇒ FEG = - 8 kN (Compressive)∑Fx = 0FED + FEGcos30o = 0FED +…

Q: g method of section, Determine the forces in members BC and BE and the horizontal p ction at G.…

A: Using method of section  ( Image has been inserted in this page )

Q: Q B 3 m C 3 m D A 3 m 2 m 3 m 3 m E F G

A:

Q: 1. Portal Method: The frame shown is subjected to lateral loads as shown. Supports S, T, U V, W and…

A:

Q: P1 3 m P2- 3 m B A -3 m P3 2 m C D

A: The structure with reactions can be shown below For equilibrium of statics (i) ∑MD =0 (cw +ve, ccw…

Q: a. Determine the slenderness ratio, above which the beam is long with respect to lateral buckling.…

A:

Q: Determine the force in member CE using method of section of the truss shown if: P= 607 Kn Q= 428 Kn…

A: To find force in member CE

Q: Calculate the forces in members AC, AD, and DE for the loaded truss. Restraining link BC is…

A:

Q: Find the force in truss DE. T = 390 N, x = 1.8 m. (Note: if the force in the truss is in tension,…

A: Joint method is used to calculate tension or compression in members of a system on which some load…

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

A: Given data in question  Load  Span member length  To find out  MEmber force

Q: For the frame shown, determine the Horizontal component of the force at E and A. Vertical component…

A:

Q: Determine the force in each member of the truss in terms of the load P and state if the members are…

A: Solution Given Data P= 12 kN L= 2.5 m

Q: Determine the force in member BE of the loaded truss. The force is positive if in tension, negative…

A: Consider the figure, Here, T is the tension and C is the compression.

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

A:

Q: 2. The A-frame is used to support the 300-lb load applied as shown. Determine the horizontal and…

A: ∑MA=0-VF×6 + 300×10 = 0VF=500 lb ↑∑V=0VA+VF=300VA=-200 lb ↓ ∑MB=0-VE×3 + 6×300=0VE=600 lb

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

A:

Q: Determine the vertical displacement of joint D. Each A-36 steel member has a cross-sectional area of…

A:

Q: Determine all bar forces AB, BC, CD and indicate whether it’s tension and compression.

A: Support Reactions :  RA + RG = 70 + 80 + 90 = 240 kN ..........(1)Taking…

Q: Determine the force in member CF. Enter a positive number if in tension, negative if in compression.…

A: Solution: Considering the Diagram: h=2.0a2-a22h=4a2-a24h=a3.75

Q: 5.9 kN 4.7 kN 3.2 m 48° 2.8 m E 2.8 m BC = CD

A:

Q: Refer to the truss as shown. Given: F1 = 64 KN F2 = 83 kN F3 = 12 kN A F -4 m B Fi 14m C G F₂ D H…

A: Find force in member GD

Q: Determine the bar forces HL, GP and indicate whether it’s tension and compression.

A: Finding the support reaction: Taking equilibrium conditions: ∑fy=0VA+VG=70+80+90=240 Taking moment…

Q: Determine the forces in members BC and CG. The forces are positive if in tension, negative if in…

A: From the given question it is required to calculate the forces in member BC and CG

Q: (b) Figure Q2(b) shows that the truss supports loads at point C and E. If the value of F = 3 kN,…

A: In this question, we shall first use method of sections to determine force in the member BE and then…

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

A:

Q: In Figure Q5(e). a statically determinate pin-jointed plane truss is pinned at A and supported on…

A:

Q: Determine the force in each member of the loaded truss. All triangles are equilateral with side…

A: Given-                Load acting on point G (P1) = 8.3 kN              Load acting on point F…

Q: Determine the forces in members BC and CG. The forces are positive if in tension, negative if in…

A: From the given truss, it is required to calculate the force in member BC and CG.

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

A:

Q: Determine the range of values of the angle 0 of the surface for the roller support at point C for…

A:

Q: Determine the force (written as a vector) which BC exerts on member AB (a) if the 950-N load is…

A: The vector is the object or in the structure which has both the magnitude and direction.  we can…

Q: Suppose that in addition to the 2-kN downward force acting at point D, a 2-kN downward force acts at…

A: Consider the figure, Here, T is the tension and C is the compression.

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

A:

Q: Determine the force in member BE of the loaded truss. The force is positive if in tension, negative…

A:

Q: Determine the force in each member of the loaded truss. All triangles are equilateral with side…

A: given Figure:- Drawing FBD of above figure:- Applying various equilibrium equations as below:-…

Q: P 200 lb 6 ft C B 240 lb 6 ft E y D

A: Resolving force: ↑+↓-240-P+200=0P=440 lb

Q: =60 degrees to the vertical, is supported by a pin at B and the 0.75in. diameter steel bar AC.(a)…

A:

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.