Ay 0 392 F a = 4.425 с At the instant the wire at B snaps, determine the reaction forces at A and the angular acceleration of the 200 kg beam if a force of 200 N is applied at point C. Assume the beam is a slender rod. Point B is located 1 I m away from point A, and the beam has a length 1 = 4 m. 4 Az x N x rad ©2 B N A UBC Engineering

Ay 0 392 F a = 4.425 с At the instant the wire at B snaps, determine the reaction forces at A and the angular acceleration of the 200 kg beam if a force of 200 N is applied at point C. Assume the beam is a slender rod. Point B is located 1 I m away from point A, and the beam has a length 1 = 4 m. 4 Az x N x rad ©2 B N A UBC Engineering

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.11P: Solve Prob. 7.10 assuming that the pick-up truck has front-wheel drive.

See similar textbooks

Similar questions

Note that when θ=0, it is initially at rest. Applying moement θ=30: a. Find ω and α b. Find reaction at B What I have so far: FBD w/ tangential and normal ΣFt = ΣFt α= (dω/dt) = (dω/dθ)= (dθ/dt) α= ω(dω/dθ) ∫ωdω = ∫α dθ (solve for ω) ΣM/A = ΣM/A
The spring-held follower AB has a mass of 0.4 kg and moves back and forth as its end rolls on the contoured surface of the cam, where r = 0.15 m and z=(0.02cos2θ)m. The cam is rotating at a constant rate of 30 rad/s. The spring is uncompressed when θ = 90. Determine the maximum force component FzFz the follower exerts on the cam. Determine the minimum force component FzFz the follower exerts on the cam.
The bar AB is uniform and has a mass of 50.0 kg. At the moment shown, the rod has an angular velocity of 4.00 rad/s and spring is stretched by 0.30 m. The force constant of the spring is 25.0 N/m.a) Determine whether or not the bar will reach the horizontal position.b) If the bar becomes horizontal, calculate its angular velocity at that position. If not, calculate the angle the bar makes with the horizontal when it comes to rest momentarily.
Determine the speed v of the 50-Mg mass when it is just over the top of the steel post, if after impact, the maximun stress developed in the post is 550 MPa. The post has a length of L = 1 m and a cross-sectional area of 0.01 m2.Est = 200 GPa, sY = 600 MPa.
When the 100-lb block is at h = 3 ft above the cylindrical post and spring assembly, it has a speed of = 20 ft>s. If the post is made of 2014-T6 aluminum and the spring has the stiffness of k = 250 kip>in., determine therequired minimum diameter d of the post to the nearest 1/8 in. so that it will not yield when it is struck by the block
The spring constants are k1 = 140N / m, k2 = 240N / m and the unstretched lengths of the springs are 0.3 m. If the 6 kg ring is released from rest from point A, calculate its velocity when it reaches point B. According to the given datum line, the total potential energy (Ve) at point A is A = 1116.86 J and the total elastic potential energy (Ve) at point B is B = 370.8 J. Neglect the dimensions of the bracelet. (L1 = 0.90 m, L2 = 1.80 m, h1 = 1.20 m and h2 = 2.40 m)
Solve Prob. 7.10 assuming that the pick-up truck has front-wheel drive.
How much work is done by the force in the spring when the slender rod rotates clockwise about the fixed pin support at O from the vertical position (where AB is horizontal) to the horizontal position? The spring has a stiffness of k = 125 N/m and an unstretched length of 0.15 m. Take d1= 0.29 m and d2= 0.85 m. Choose the correct answer. a) 94.9 Joule b) 99.9 Joule c) -99.9 Joule d) 0 Joule e) -94.9 Joule
The 4-lb collar C fits closely the smooth shaft. The spring in unstretched when s=0 and its stiffness is 6 lb/ft. AT s=0 ft, the collar is given a velocity of 19ft.s-1. The height is 0.6-ft. determine the position of the collar when its velocity is 0 ft.s-1
The 5 kg cylinder is released from rest in the postion shown in the figure below. Determine the maximum compression xmax of the spring. The stiffness of the spring is 1800 N/m.
A railroad car that is assumed to be rigid and has a mass of 80 Mg ismoving forward at a speed of v = 0.2 m>s when it strikes a steel 200 mmby 200 mm post at A, Fig. a. If the post is fixed to the ground at C,determine the maximum horizontal displacement of its top B due to theimpact. Take Est = 200 GPa.
Determine the maximum compression of the spring after the collision.