B 0.5 m - 0.4 m -0.6 m 12 kN 20 kN

Q: Draw the shear and bending-moment diagrams for the beam and loading shown, and determine the maximum…

A: Reactions at A and B are: Sum of the moment about A and B are equal to zero Where, ∑MB is the sum…

Q: The steel shaft is subjected to the two loads. If the journal bearings at A and B do not exert an…

A: Data given- Allowable stress = 180 Mpa Load = 4KN at an angle of 30° from y axis

Q: Q3) The circular shaft is supported by smooth journal bearings at A and B that only exert vertical…

A:

Q: Determine the smallest allowable diameter of the shaft which is subjected to the concentrated…

A:

Q: The bar has a thickness of 1 in. and the allowable bending stress is sallow= 30 ksi. Determine the…

A:

Q: PROBLEM: The beam shown is made by gluing together four pieces 300mm x 12mm wooden planks as shown.…

A:

Q: Determine the absolute maximum bending stress in the 80-mm-diameter shaft which is subjected to the…

A: the reaction forces are shown in the figure given below. balancing forces in vertical direction  Ay…

Q: The shaft is supported by a thrust bearing at A and journal bearing at D. If the shaft has the cross…

A: Given data: Inner radius, r = 25 mm Outer radius, R = 40 mm Therefore, Inner diameter, d = 50 mm…

Q: Determine the absolute maximum bending stress in the beam, assuming that the support at B exerts a…

A: Free body diagram of the beam is given as, On using equilibrium of forces in a horizontal…

Q: Determine the maximum permissible positive moment capacity (NOT bending stress) for this beam cross…

A:

Q: Determine the absolute maximum bending stress in the 1.5-in.-diameter shaft. The shaft is supported…

A: Given data: Diameter of the shaft , d = 1.5 in.   Let, Y = distance between neutral fibre and…

Q: An L2 steel strap having a thickness of 0.125 in. and a width of 2 in. is bent into a circular arc…

A:

Q: A half section of pipe rests on a frictionless horizontal surface as shown. If the half section of…

A: Draw the free-body diagram of the half section of the pipe.

Q: Determine the bending moment acting at each of the following locations: (a) x = 14.0-ft (i.e., just…

A:

Q: 450 lb/ft Q2/ If the beam has a square cross section of 9 in. on each side, determine the absolute…

A:

Q: The bar has a thickness of 0.5 in. and the allowable bending stress is sallow= 20 ksi. Determine the…

A: The maximum stress in the beam is written as, The ratio r/h and w/h is written as,

Q: The curved member is subjected to the moment of M = 50 kN # m. Determine the percentage error…

A: Draw the diagram of the curved beam with the proper specification. Here, ri is the radius of the…

Q: An A-36 steel strap having a thickness of 10 mm and a width of 20 mm is bent into a circular arc of…

A: Given, T = 10 mm width = 20 mm  radius of curvature (r)= 10 m The Young's modulus of A36 steel is…

Q: Determine the magnitude of the internal loads(normal, shear, and bending moment) at point C.

A: The given member can be cut into two parts along C and the above part can be drawn as below, Here,…

Q: The shaft is supported by smooth journal bearings at A and B that only exert vertical reactions on…

A: A moment is a movement of the body when a body is rotating on an axis. The moment is also known as…

Q: Determine the smallest allowable diameter of the shaft. The shaft is supported by a thrust bearing…

A: Given data Allowable bending stress, σ = 22 ksi. Draw the free-body diagram of the shaft. Apply…

Q: Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum…

A: Given

Q: The shaft is supported by a thrust bearing at A and journal bearing at C. If the material has an…

A: Given data Allowable bending stress of the shaft, σallowable = 24 ksi. Draw the free-body diagram…

Q: The 50-mm-diameter shaft is supported by journal bearings at A and B. If the pulleys C and D are…

A: Let's draw the free body diagram to show the reactions at support,

Q: The simply supported beam of rectangular cross section carries a distributed load of intensity w0 ¼…

A:

Q: The member has a circular cross section. If the allowable bending stress is sallow = 100 MPa,…

A: Given: Allowable bending stress = 100 MPa Diameter of circular cross-section = 200 mm We know that,…

Q: Part A If it is simply supported and carries the distributed loading shown, determine the variation…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: The wood beam has a rectangular cross section in the proportions shown. Determine its required…

A:

Q: Determine the absolute maximum bending stress in the 2-in.-diameter shaft. There is a journal…

A: Given data: Diameter of shaft = 2 in  To determine: Absolute maximum bending stress Before…

Q: The beam has a rectangular cross section as shown. Determine the largest intensity w of the uniform…

A: Given data:  Bending stress in the beam, σb,max=10 MPa Determine the largest uniform intensity, w

Q: For the given cross-section, if the width b = 6.6 in., the height h = 8.4 in., and the internal…

A:

Q: The bar has a thickness of 0.5 in. and is subjected to a moment of 600 lb # ft. Determine the…

A: Given: r=0.3 inh=2 inw=6 int=0.5 inM=600 lb.ft

Q: The curved beam is made from a material having allowable bending stress of sallow = 24 ksi.…

A: Given Data Allowable bending stress is: σb=24 ksi=24000 psi

Q: Determine the maximum magnitude of the bending moment M so that the bending stress in the member…

A: Moment of inertia about Y axis,IY=112[BD3-bd3]⇒IY=112[6×63-4×43]⇒IY=86.667 in4Here,Moment of inertia…

Q: Determine the shear force acting at each of the following locations: (a) x = 0+ ft (i.e., just to…

A:

Q: Determine the internal forces (axial force, shear force, and bending moment) at point j of the…

A:

Q: The reaction of the ballast on the railway tie can be assumed uniformly distributed over its length…

A: Given Data  Bending stress, 1.5 ksi Total reaction=15+15=30 kip load intensity, W=30/(5+2(1.5))=3.75…

Q: How to calculate the bending stress at point B in the section shown? Bending Stress at B y Point B y…

A:

Q: Determine the bending stress at point A of the beam, and the orientation of the neutral axis. Using…

A: The moment of inertia about the y' axis is given by My'=-3sin45°=-2.121 kip·ft The moment of inertia…

Q: The bending moment Mis 3 m M

A: Given data : Point load=P Distance from point load to a point where moment is to be found=d…

Q: If the beam is subjected to a bending moment of M = 48 kN m , determine the maximum bending stress…

A: Given data: The magnitude of bending moment, M = 48 kN·m. Calculate the moment of inertia of the…

Q: *11-84. Determine, to the nearest millimeter, the smallest allowable diameter of the shaft which is…

A: givenallowable bending stress σallow=150MPa

Q: If the beam in Prob. 6–28 has a rectangular cross section with a width b and a height h, determine…

A: Given Data: The load acting on the beam is 12 kN and 20 kN. The free-body diagram of the beam  can…

Q: Determine the smallest allowable diameter of the shaft which is subjected to the concentrated…

A: