Besides indicating ABS faults for some systems, the red brake warning lamp on the instrument panel can indicate failure of the ___ brakesystem, application of the ___ brake, or low fluidlevel in the ___.

Besides indicating ABS faults for some systems, the red brake warning lamp on the instrument panel can indicate failure of the _ brakesystem, application of the _ brake, or low fluidlevel in the ___.

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter53: Antilock Brake, Traction Control, And Stability Control Systems

Section: Chapter Questions

Problem 6RQ: Besides indicating ABS faults for some systems, the red brake warning lamp on the instrument panel...

See similar textbooks

Related questions

Q: Which of these provides stringent classifications formulated for engine oils used in European…

A: ACEA , Association de constructors Europeans d'automobiles.

Q: Describe the 4 distinct modes the vehicle should be operated in during a road test when diagnosing…

A: Four distinct modes the vehicle should be operated in during a road test when diagnosing final…

Q: Which of the following statements about drum brakeshoes is not true?a. Web thickness varies only…

A: Brake shoes are a major part of a drum brake system. these crescent-shaped components are made up of…

Q: Technician A says that a malfunction of the ABS causes the control module to shut off or inhibit the…

A: The system will be shut down if any malfunction is monitored in the ABS because the control module…

Q: List at least five separate checks that should be made during the visual inspection of tje…

A: The transmission/transaxle are visually inspected after a certain interval of time. This method of…

Q: b) What would happen if the ABS system having a fault? Explain why this could happen.

A: Given ABS To find Consequence of ABS faults Reason for ABS faults

Q: Comparing ABS system to hydraulic break of a vehicle

Q: causes for damage to the surface of a pressure plate. Technician A says a worn clutch disc can score…

A: Pressure plate is an important part of vehicles clutch system. It applies pressure to clutch disc to…

Q: Which of the following is not a factor in determiningthe effectiveness of a brake system?a. Heat…

A: Given Data : Effectiveness of brake system

Q: During a brake inspection, the inner brake pad is found to be 3mm thick, while the outside pad is…

A: Front and rear brake pads normally wear differently. When your vehicle is moving, the forward…

Q: How does air-over Hydraulic brake system work

A: Air brakes are much easier to attach than hydraulic brakes, and using air rather than hydraulic…

Q: if you read the scan codes on the vehicle and U0121 was standa for lost communication with antilock…

A: Solution::: == The U0121 code stand for Data bus: anti-lock brake system (ABS) control module - no…

Q: 1. Determine brake power and brake thermal efficiency of the engine. 2. Analyze the effect of…

Q: What is the difference between block brakes with short and long shoes?

A: Block shoe brake : These are mechanical brakes which are operated by mechanical elements ( springs ,…

Q: Technician A says that a malfunction of the ABS causes the control module to shut off or inhibit the…

A: Automobile

Q: When replacing brake pads on a vehicle: Tech-nician A works on one wheel before beginning work on…

Q: how is the braking force of drum-type brakes controlled

A: Brake: The brake is defined as a machine element which is used to retard the moving member or to…

Q: Technician A days that a weak suspension spring can cause a loss of traction during acceleration.…

A: The suspension spring is part of the shock absorber assembly. The main work of shock absorbers is to…

Q: Why do we need to diagnose the transmission/transaxle failure?

A: It is very important to diagnose the transmission failures in any vehicle.There are many factors…

Q: When discussing CV joint diagnosis, Technician A says that the complete failure of a CV joint may…

A: Solution:

Q: When performing the air brake system leakage test, the Certified Inspector must reject the vehicle…

A: Answer = False

Q: 108) Technician A says that engine management malfunctions may be misinterpreted as transmission…

A: Engine management malfunctions can be seen by malfunction indicator lamp . this indicator shows that…

Q: We want to keep this vehicle speed constant As manipulation we want automatically adjust gas\brake…

A: Given Car To find Block diagram to maintain uniform velocity

Q: Define Braking loads

A: Braking load/force is the frictional force that cats tangentially between the brake pads and…

Q: After replacing a vacuum booster, the brakes lock up on a road test. Technician A says there is air…

A: After replacing a vacuum booster, the brakes lock up on a road test. Technician A says there is air…

Q: fferent parts of the brakes system of an off-road bicycle

A: introduction In the marine and seaward industry, plan and hardware setups fluctuate from one…

Q: describe four distinct modes the vehicle should be operated in during a road test when diagnosis…

A: Introduction: The test car approach was utilized to acquire journey time data. This approach has…

Q: "Comparing ABS system to hydraulic break of a vehicle"

A: There are many advantages of ABS brakes (anti-lock braking system) over hydraulic brakes - ABS…

Q: A discussion concerning CV joint testing is being held. Technician A says that a recommended method…

A: CV Joint: CV joint means Constant Velocity Joint. They are used to transfer the power in a variable…

Q: Which of the following is true about a brake service? A. It should always include a…

A: Break : A brake is a mechanical device that inhibits motion by absorbing energy from a moving…

Q: When reassembling an overhauled brake caliper: Technician A cleans brake components in dena-tured…

A: reassembling an overhauled brake calliper: Technician A cleans brake components in denatured…

Q: andard efficiency & brake thermal efficiency of engin

A: given:brake thermal efficiency=24.4%air thermal efficiency=53.4%

Q: The functions of a splash shield are being dis-cussed: Technician A says that disc brakes will…

Q: A vehicle with a direct TPMS just had all 4 tires replaced, yet the TPMS warning light is on.…

A: Direct TPMS. This is often the framework that utilizes sensors on each wheel to degree the tire…

Q: iscuss the mechanism of each type of Brake systems.

A: Brakes are classified into different types. 1.According to the applications Running / foot brake…

Q: significance of a combined cbs and abs braking system

Q: List at least five separate checks that should be made during the visual inspection of the…

A: Checks need to be done during the visual inspection of the transmission/transaxle are:

Q: A vehicle with a direct TPMS system keeps showing “Low-Left Front Tire,” but when checked, the tire…

A: Direct TPMS. This is often the framework that utilizes sensors on each wheel to degree the tire…

Q: Explain why modern hydraulic braking systems are dual designs, and why this is important.

A: Dual designs are used in the modern hydraulic braking systems as it provides application on all the…

Q: What tyre wear pattern will result from excessive negative camber?(Automotive cert.4)

A: following is the answer to the above question-

Q: Servicing the vehicle for every 5000 km is an example of preventive maintenance . Select one: O True…

A: True By the defination of preventive maintenance

Q: While discussing valve body assemblies in late-model transmissions: Technician A says that the valve…

A: Automatic transmission valve body is a major part of a vehicle’s automatic transmission system. It…

Q: What is the principle of the balancing act in tires?

A: The tyre will roll smoothly when all regions of the wheel-tire unit are as evenly weighted as…

Q: Technician A says that some antilock brake systemsuse a lateral acceleration sensor in addition to…

A: The automatic traction control system applies braking force to the wheel in trouble, to get out of…

Q: Discuss about antilock braking system and its importance in modern vehicles

A: ABS systems in cars stop them from skidding and preventing the wheels from locking up during the…

Q: Discuss the concept of Brake Specific Fuel Consumption (BSFC)

A: Brake specific fuel consumption – It is the fuel required per unit of work output. It is also…

Q: Technician A says power brakes are designed with vacuum-assisted units that use engine vacuum.…

A: Most vehicles use vacuum suspended units (vacuum promoters), which utilize a vacuum-fueled sponsor…

Q: QI: a. List (only) brake types.

A: As per bartleby guidelines we are allowed to solve only 1st question if multiple questions are…

Concept explainers

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.

Question

Besides indicating ABS faults for some systems, the red brake warning lamp on the instrument panel can indicate failure of the ___ brake
system, application of the ___ brake, or low fluid
level in the ___.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

VIEW

Step 2: Explanation

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Clutches, Brakes, Couplings and Flywheels

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An ABS modulates brake pressure. What does this mean?
Technician A says that each ABS has its own diagnostic procedure involving use of the brake and antilock warning lamps, special testers, breakout boxes, scan tools, troubleshooting charts, and wiring diagrams. Technician B says that ABSs vary in the number of codes they can store and whether they will retain the code in memory when the ignition is turned off. Who is correct? Technician A only Technician B only Both A and B Neither A nor B
Discuss the concept of Brake Specific Fuel Consumption (BSFC)
Define the difference between an integrated and a nonintegrated antilock braking system.
What is the significance of a combined cbs and abs braking system?
Technician A says that a malfunction of the ABS causes the control module to shut off or inhibit the system. Technician B says that a loss of hydraulic fluid or power booster pressure disables the antilock brake system. Who is correct? a. Technician A only b.Technician B only c.Both A and B d.Neither A nor B
Define the difference between an integrated and anonintegrated antilock braking system.
Technician A says power brakes are designed with vacuum-assisted units that use engine vacuum. Technician B says power brakes are designed with vacuum-assisted units that use vacuum developed by an external pump. Who is correct? a. A only b. B only c. both A and B d. neither A nor B Synthetic linings are made of _____ a. fiberglass b. aramid fiber c. both A and B d. neither A nor B All manufacturers recommend a specific sequence to follow when bleeding a vehicle’s brakes. a. True b. False Organic friction material _____ semimetallic materials. a. is quieter than b. is more fade resistant than c. requires higher pedal pressure than d. wears out faster than
Technician A says that a malfunction of the ABS causes the control module to shut off or inhibit the system. Technician B says that a loss of hydraulic fluid or power booster pressure disables the antilock brake system. Who is correct?a. Technician A only.Technician B only.Both A and B.Neither A nor B
Technician A says that it is normal for the amber brake lamp to light when the ABS is activated during braking. Technician B says that it is normal for the red brake lamp to be on whenever the ignition is on and the engine is off. Who is correct? Technician A only Technician B only Both A and B Neither A nor B
While road testing a car equipped with an ABS: Technician A says that during heavy braking, several pulses may be felt through the brake pedal. Technician B says that a spongy pedal during normal braking is normal. Who is correct? Technician A only Technician B only Both A and B Neither A nor B
While discussing pull during braking: Technician A says that this can be caused by one tire being underinflated. Technician B says that a frozen wheel cylinder on one side of the car can cause this. Who is correct? Technician A only Technician B only Both A and B Neither A nor B