c) If the cross-section of the beam is as shown in Figure 2.2, calculate the location of the centroid C with respect to the bottom of the cross-section and the moment of inertia about the centroidal axis x. 2.00 in. 4.00 in. 1.50 in. y 1.50 in. 2.00 in. 0.75 in. <-1.50 in. 0.75 in. 2.00 in. Figure 2.2 Cross-section X

c) If the cross-section of the beam is as shown in Figure 2.2, calculate the location of the centroid C with respect to the bottom of the cross-section and the moment of inertia about the centroidal axis x. 2.00 in. 4.00 in. 1.50 in. y 1.50 in. 2.00 in. 0.75 in. <-1.50 in. 0.75 in. 2.00 in. Figure 2.2 Cross-section X

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A support is a fixed support, B is a movable support, and the distance of the cantilever in both directions is given as 3 m, triangularThe normal force (N), shear force (V) of the frame system acting on distributed loads, uniformly distributed loads and single loads.draw bending moment (M) diagrams? (AC = 1m, CD = 2m, Console overhangs: 3m, OD = 4m, OE = 4m,BE= 2m)
The length of the 3/32 in.diameter steel wire CD has been adjusted so that with no load applied, a gap of 1/16 in. exists between the end B of the rigid beam ACB and a contact point E. Knowing that E=29 X 10⁶ psi, determine where a 50-lb block should be placed on the beam in order to cause contact between B and E.
A tapered cantilever beam AB supports a concentratedload P at the free end (see figure). The crosssections of the beam are rectangular with constantwidth b, depth dA at support A, and depth dB = 3dA/2 at the support. Thus, the depth d and moment of inertiaI at distance x from the free end are, respectively, d = (dA/2L)(2L+x) I=(bd3/12) =(bd3A/96L3)(2L+x)3 = (IA/8L3)(2L+x)3in which IA is the moment of inertia at end A of thebeam.Determine the equation of the deflection curveand the deflection δA at the free end of the beam dueto the load P.
.15 2.16 The three forces acting on the beam can be replaced with a single equivalent force R. Determine the angle θ and R. 25kN P2 60 kN P3 80 kN 40° 50° 4 m 6 Figure P2.16 COMPANY
A built-up I-section is composed of two 10" x 3/8" flange plates welded to a 12" x 1/4" web plate. Both flanges and web are made of A992 steel. The column is 10-ft high with one end pinned and the other is free to translate but restricted from rotating. Determine the radius of gyration about the weak axis. Select one: a. 2.44 b. 5.55 c. 3.11 d. 4.22
beam x from c-d
Design a most economical spiral-column cross-section to support factored forces and end moments of Pu = 1,600 kips and Mu = 150 kip-ft. Assume that the centroid of each longitudinal bar from the edge of the column is 2.5 inch. What is the trial diameter dimension of the section in inch if ρg = 0.025?
A crossed belt goes around the pulleys A and B having radii of 14 cm and 7cm, respectively. The distance between centers of the two pulleys is 36 cm.a) Determine the angle of contact of the belt on the bigger pulley.b) Determine the length of the common internal tangent.c) Determine the total length of the belt.
Without sidesway frame Find deflection at B
Solve fast please I need correct answes
16 -The stair beam in the figure will have support reactions. A support is a fixed, B support is a sliding joint. loads P1= 15 kN, P2= 30 kN, dimensions a = 2 m, b = 6 m, c = 4 m. Accordingly, Bx = ?A) 3.75B) None.C) 18.75D) 0E) 30
A beam ABCD with a vertical arm CE issupported as a simple beam at A and D (see figure).A cable passes over a small pulley that is attachedto the arm at E. One end of the cable is attached tothe beam at point B. The tensile force in the cable is1800 lb. (a) Draw the shear-force and bending-momentdiagrams for beam ABCD. Note: Disregardthe widths of the beam and vertical armand use centerline dimensions when makingcalculations.(b) Repeat part (a) if a roller support is added at Cand a shear release is inserted just left of C (seefigure part b).