Answered: Calculate the amount of torque…

Calculate the amount of torque generated by the rod with circular cross-section as shown in the figure below, if the force applied is 48 lb. The diameter of the rod is 5 in.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.3.3P: Repeat Problem 3.3-1, but now use a circular tube with outer diameter d0= 2.5 in. and inner diameter...

See similar textbooks

Related questions

Q: For the shaft in below, motor gives a 500 Nm torque on the shaft when it is rotation with a constant…

Q: Q.5. A single torque of T = 50 N.m is applied to a compound torsion member as shown in figure (5).…

Q: A flange bolt coupling has 10 steel coupling 1 inch diameter bolts evenly tighten around a 16.34 in.…

Q: In drilling a deep oil well the drill shaft, consisting of sections of “drill rod”, is powered from…

Q: |For the shaft shown in figure is made - Aluminium Steel of two material on the left is made of 1 kN…

Q: Figure 4 shows a 50mm diameter solid shaft made out of steel whose modulus of rigidity is 75,000…

Q: For the shaft shown in the figure below, compute the angle of twist of pulleys B and C relative to…

Q: 2. For the system shown below, compute the maximum torque it can accommodate if a is 2000mm and b is…

A: Find the maximum torque .

Q: An input shaft of a gearbox with motor power P = 7 kW and rotation number n = 1300 rpm. The diameter…

Q: For the shaft in below, motor gives a 500 Nm torque on the shaft when it is rotation with a constant…

A: First consider the section BC, TBC=200 N·m dBC=44 mm=0.044 m Now the polar moment of inertia of…

Q: Referring to Figure Qla, assuming a hollow cylindrical block at the mid-section of the femur with an…

Q: For the shaft in below, motor gives a 500 Nm torque on the shaft when it is rotation with a QUESTION…

A: Given data Torque at (B) = 200 N-m Torque at (C) = 300 N-m Torque at (D) = 500 N-m shaft of dia at…

Q: The torsional assembly shown in Figure P6.45 consists of solid 2.50 in. diameter aluminum [G=4,000…

Q: Figure Q6 shows a circular shaft AB and a square shaft BC where it is fixed at C. а. Determine the…

Q: A solid constant-diameter circular shaft is subjected to the torques of TA = 440 Ib-ft, TB = 1030…

Q: Question 6 Figure Q6 shows a circular shaft AB and a square shaft BC where it is fixed at C. a.…

A: Part (a) The data given is,

Q: A hollow aluminum rod has a max shear stress of 0.075 GPa. What is the maximum torque that can be…

A: Given: The maximum shear stress is τ=0.075 GPa. The outer diameter is D=0.8 m. The thickness is t=5…

Q: A flanged bolt coupling consists of six 10-mm diameter steel bolts on a bolt circle 300 mm in…

Q: Calculate the torsional shear stress because of a torque of 88 in-lb in a circular shaft having a…

Q: -) A hollow circular steel shaft has a 150 mm outer diameter, and a 100 mm inside diameter. The…

Q: Problem 4 A 200-mm-diameter pulley is prevented from rotating relative to 60-mm-diameter shaft by a…

Q: 900 N-m A 1100 N-m B. 2 m 800 N-m 3 m

A: A rotating member usually is a circular cross-section used to transmit rotational power from one…

Q: PROBLEM 1. A hollow cylindrical steel shaft is 1.5 m long and has inner and outer diameters…

A: As per given question L=1.5m D1=40mm D2=60mm Modulus of rigidity =77gpa We have to determine a)…

Q: A solid constant-diameter circular shaft is subjected to the torques of TA= 480 lb-ft, TB = 1030…

Q: Pls answer thank you! A 2 in diameter 6-spline shaft ( d= 0.85D, W= 0.25D, h= 0.075D ) and to slide…

A: Given DataDs=2inn=6d=0.85D=1.7inW=0.25D=0.5inh=0.075D=1.5inL=212inF=2500lbs

Q: A solid constant-diameter circular shaft is subjected to torques TA = 420 lb- ft, TB = 1,040 lb- ft,…

A: Right hand rule states that when axis direction is indicated by the thumb, the direction of fingers…

Q: A shaft system ABC consists of a solid bar AB welded to a hollow bar BC. The shaft is subjected to…

A: Strength of shaft The strength of the shaft means maximum torque that can be transmitted by shaft.…

Q: Figure Q6 shows a circular shaft AB and a square shaft BC where it is fixed at C. a. Determine the…

A: Given : Torque = 2000 N.m The length of shaft AB = 600 mm The length of shaft BC = 600 mm The…

Q: 25 marks Q4: For the aluminum pipe shown in figure below (G-27GPa).Determine (a) The torque To…

Q: A shaft with splines of a diameter of 50 mm, as shown in the figure below, transmits a torque of…

A: Spline shafts are commonly employed in autos, aeroplanes, and earthmoving gear because they can…

Q: A B 55² 240 N.mm 420 N.mm 300 N.mm 480 N.mm Figure 1 - Torques applied to the driveshaft 1) DERIVE…

A: Find the Angle of twist expression Shaft diameter Maximum shear stress

Q: A circular steel shaft of diameter 30 mm is subjected to a torque of 60 N-m. Calculate the angle of…

A: Given:Diameter of steel shaft,d=30mm=301000m=0.03 mTorque on shaft,T=60 NmLength of shaft,L=20…

Q: n in the figure. Find the angular rotation of D, the right end of one shaft, with ect to A, the left…

Q: 3) Two circular shafts (shown in Figure) made of the same material and have the same length are…

Q: motor transmits 180 hp to the driving pulley, in the figure assuming that A takes 40 hp and C takes…

A: find the diameter of the shaft .

Q: 2. For the system shown below, compute the maximum torque it can accommodate if a is 2000mm andb is…

Q: 1) A straight hollow shaft is fixed at one end and free at the other end. The shaft is made of…

A: A moment of inertia is a mass of the body when a body is rotating on an axis. The moment of inertia…

Q: The hollow rod shown below is 2.99 meters long and is subjected to a torque of 988 Nm at end B. The…

Q: For the aluminum pipe shown in figure below (G=27GPa).Determine (a) The torque To causing an angle…

A: Given data: Shear modulus of material = G = 27 GPaOuter diameter = D = 50 mmInner diameter = d = 40…

Q: A thin-walled tube having a semi circular shape has an outside diameter of 50 mm and a wall…

Q: A solid circular steel shaft of diameter 20 mm is enclosed within a brass hollow circular shaft of…

Q: A flanged bolt coupling consists of eight 10 mm diameter steel bolts on a bolt circle 400 mm in…

Q: PROBLEM 3 Two shafts are being connected by a coupling which is held together by four 3/4-in…

Q: 5.2 A hollow bronze shaft of 75 mm outside diameter and 12.5 mm thick is coaxlal Willl d solid steel…

Q: 3- Using the following theoretical relationship, determine the theoretical relationship between the…

Q: A flanged bolt coupling consists of six 12.5 – mm steel bolts evenly spaced around a bolt circle 300…

Q: Answer the following problem. Show your complete solution. Use 4 decimal places. Calculate the…

A: Given data: The power transmits, P = 45 kW. The speed of the shaft, N = 120 rpm. The permissible…

Q: 1000mm Input shaft A 100mm Bearing support 200mm 450mm pulley pulley 200mm 150mm 450mm pulley…

A: NOTE:- As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost…

Q: A solid constant-diameter circular shaft is subjected to the torques of TA = 560 lb·ft, TB = 1080…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

Calculate the amount of torque generated by the rod with circular cross-section as shown in the figure below, if the force applied is 48 lb. The diameter of the rod is 5 in.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A solid circular bar A BCD with fixed supports at ends A and D is acted upon by two equal and oppositely directed torques T0, as shown in the figure. The torques arc applied at points B and C each of which is located at distance x from one end of the bar. (The distance x may vary from zero to L/2.) For what distance x will the angle of twist at points B and C be a maximum? What is the corresponding angle of twist 0max?
A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.
A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the figure. The allowable shear stress in the brass is 12 ksi. What is the maximum permissible value of the torques T1? If a hole of diameter 0.625 in. is drilled longitudinally through the bar, as shown in part b of the figure, what is the maximum permissible value of the torques T2? What is the percent decrease in torque and the percent decrease in weight due to the hole?
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A propeller shaft of solid circular cross section and diameter d is spliced by a collar of the same material (see figure). The collar is securely bonded to both parts of the shaft. What should be the minimum outer diameter dyof the collar in order that the splice can transmit the same power as the solid shaft?
A magnesium-alloy wire of diameter d = 4mm and length L rotates inside a flexible tube in order to open or close a switch from a remote location (see figure). A torque Tis applied manually (either clockwise or counterclockwise) at end 5, thus twisting the wire inside the tube. At the other end A, the rotation of the wire operates a handle that opens or closes the switch. A torque T0 = 0.2 N · m is required to operate the switch. The torsional stiffness of the tube, combined with friction between the tube and the wire, induces a distributed torque of constant intensity t = 0.04N m/m (torque per unit distance) acting along the entire length of the wire. (a) If the allowable shear stress in the wire is T allow = 30 MPa, what is the longest permissible length Lmaxof the wire?
A solid circular bar ABCD with fixed supports is acted upon by torques T0and 2T0at the locations shown in the figure. (a) Obtain a formula for the maximum angle of twist 0maxof the bar. (b) What is 0max if the applied torque T0at B is reversed in direction?
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
Compare the angle of twist 1 for a thin-walled circular tube (see figure) calculated from the approximate theory for thin-walled bars with the angle of twist 2 calculated from the exact theory of torsion for circular bars, Express the ratio 12terms of the non-dimensional ratio ß = r/t. Calculate the ratio of angles of twist for ß = 5, 10, and 20. What conclusion about the accuracy of the approximate theory do you draw from these results?
A solid circulai' aluminum bar AB is fixed at both ends and loaded by a uniformly distributed torque 150N·n/m. The bar has diameter d = 30 mm. Calculate the reactive torques at the supports and the angle of twist at midspan. Assume that G = 28 GPa.
A circular tube of aluminum is subjected to torsion by torques T applied at the ends (see figure). The bar is 24 in. long, and the inside and outside diameters are 1.25 in. and 1.75 in., respectively. It is determined by measurement that the angle of twist is 4° when the torque is 6200 lb-in. Calculate the maximum shear stress in the tube, the shear modulus of elasticity G, and the maximum shear strain (in radians). If the maximum shear strain in the tube is limited to 2.5 × 10-3 and the inside diameter is increased to 1.375 in., what is the maximum permissible torque?
Repeat Problem 3.3-1, but now use a circular tube with outer diameter d0= 2.5 in. and inner diameter di= 1.5 in.