3. Calculate the inertia of the flywheel group resulting from the suspension of the weight of the amount (100 gm) in the weight carrier, if the number of turns of the thread (15) and the distance between the center of gravity and the surface of the earth (137.8 cm) and the time taken for the weight to hit the ground (20.63 sec) and the number of flywheel turns after it stops (11) and the diameter of the axis of the rotating wheel (2.09 cm).

3. Calculate the inertia of the flywheel group resulting from the suspension of the weight of the amount (100 gm) in the weight carrier, if the number of turns of the thread (15) and the distance between the center of gravity and the surface of the earth (137.8 cm) and the time taken for the weight to hit the ground (20.63 sec) and the number of flywheel turns after it stops (11) and the diameter of the axis of the rotating wheel (2.09 cm).

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter10: Fixed-axis Rotation

Section: Chapter Questions

Problem 74P: When tightening a bolt, you push perpendicularly on a wrench with a force of 165 N at a distance of...

See similar textbooks

Similar questions

A 22.5 kg child is riding a playground merry-go-round that is rotating. If the child is 1.5 m from center of the merry-go-round which is rotating at 17 rev/min, then what is the magnitude of the force, F1, in newtons, required to keep the child in uniform circular motion?
It is known that an aluminum bar breaks when it is subjected to a traction of 25Kn. One end of the bar is attached to a motor and the other to a steel ball with a mass of 17 kg . When the engine is started, the ball describes a horizontal circumference with a radius 5.0 m. If engine speed is increased gradually, its rotation period decreases gradually as well. P
A centrifuge rotor rotating at 9500 rpmrpm is shut off and is eventually brought uniformly to rest by a frictional torque of 2.28 m⋅N If the mass of the rotor is 4.19 kg and it can be approximated as a solid cylinder of radius 0.0490 m , through how many revolutions will the rotor turn before coming to rest? How long will it take?
3, Two flywheels having a mass of 50 kg each rotate with the same frequency 360 rev/min. After they were left on their own, the first stopped after 1min and 40s, and the second after committing 300 rev. Determine the moments of friction in the bearings of each of the shafts and compare them with each other, assuming that the first flywheel is made in the form of a solid disk, and the second so that its mass can be considered uniformly distributed over the rim. Flywheels radii are 0.5m.
Of the two frictionless inclined planes with slopes of 30 ° and 53 °, masses m1 = 4kg on the first and m2 = 2kg on the second. These two masses are attached to the two ends of a rope passing through a reel of radius R = 50cm and moment of inertia I = 2 kg m2. Find the accelerations (the linear accelerations of the masses and the angular acceleration of the pulley) and the stresses in the rope. NOTE: The reel is rotating, the tensions in the rope are not equal.
Why must the torque due to the weight be equal in magnitude?
A sphere and a cylinder with equal weights of 400N and equal radio of 0.30m are joined together by a steel rod as shown. Assume that they are free to roll down the incline and both bearings are frictionless. Disregarding the mass of the rod, determine the linear acceleration of the system and the force P in the rod.
the knee extensors insert on the tibia at an angle of 30 degrees (from the longitudinal axis of the tibia), at a distance of 3 cm from the axis of rotation at the knee. how much force must the knee extensors exert to produce an angular acceleration at the knee of 1 rad/s^2. given a mass of the lower leg and foot of 8.8 kg and a radius of rotation of 23 cm?
A 25 lb solid sphere is at the top of an incline plan 5 ft high and 13 ft long. What linear speed does the sphere acquire in rolling down the slope?
In the Cavendish balance apparatus shown in Figure 13.4 in the textbook, suppose that m1 = 1.50 kg, m2 = 27.0 kg, and the rod connecting each of the pairs of masses is 31.0 cm long. Once the system reaches equilibrium, each pair of masses, m1 and m2, are separated by a distance of 13.0 cm center-to-center. A. Find the magnitude of the net force on one of the small masses, m1. B. Find the gravitational torque (about the rotation axis) on the rotating part of the apparatus. Ignore any forces on the connecting rods in your calculation. C. Suggest some ways to improve the sensitivity of this experiment.
A centrifuge rotor rotating at 9300 rpm is shut off and is eventually brought uniformly to rest by a frictional torque of 1.66 m⋅N. If the mass of the rotor is 4.58 kg and it can be approximated as a solid cylinder of radius 0.0440 m, through how many revolutions will the rotor turn before coming to rest? Express your answer to three significant figures. How long will it take? Express your answer to three significant figures and include the appropriate units.
When tightening a bolt, you push perpendicularly on a wrench with a force of 165 N at a distance of 0.140 m from the center of the bolt. How much torque are you exerting in newton-meters (relative to the center of the bolt)?