Calculate the largest weight W that can be attached to the two wires shown in Figure P-103. The stresses in wires AB and AC are no more than Mpa 100 and Mpa 150 respectively, knowing that the cross-sectional area of wire AB is 400 square millimeters and for wire AC is 200 square millimeters. Answer

Calculate the largest weight W that can be attached to the two wires shown in Figure P-103. The stresses in wires AB and AC are no more than Mpa 100 and Mpa 150 respectively, knowing that the cross-sectional area of wire AB is 400 square millimeters and for wire AC is 200 square millimeters. Answer

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.5.8P: A solid circular bar of steel (G = 78 GPa) transmits a torque T = 360 N - m. The allowable stresses...

See similar textbooks

Related questions

Q: A steel bar of cross-sectional area 200 mm^2 is loaded as shown in Fig. Find the change in length of…

A: For solution refer below images.

Q: 1. Three long parallel wires equal in length are supporting a rigid bar connected at their bottoms…

A: It is the conceptual numerical of mechanics of solid portion and used concept is axial deformation…

Q: D A 10kN 28kN + → 60KN 44KN + 120cm 80cm Ост 40cm Figure 1 a) Draw a Free Body Diagram for each…

Q: 4. An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Fig. Axial…

Q: given figure, 40 kN 60 KN determine the .D normal stress + 2m - Sm Sm in MPa at segment AB.…

Q: Two steel wires support a movable overhead camera weighing W=25lb (see figure) used for close-up…

A: Data given-

Q: The rectangular piece of wood, 50 mm by 100 mm, is used as a compression block. The grain of the…

A: To find largest axial force P

Q: A solid bar has a diameter of 40 mm and subjected to the loadings shown in Figure 2. The supports at…

Q: Q2) The lower ends of the three steel rods shown in (FIG. Q2) are at the same level before the force…

Q: An aluminium rod is attached between a steel rod and a bronze rod as shown in Figure-3. The axial…

Q: A homogeneous 800 kg bar AB is supported at either end by a cable as shown in Fig. P-105. Calculate…

A: Stress is the internal resisting force that offers strength to the applied force. If the stress…

Q: A uniform concrete slab of mass M is to be attached to two rods whose lower ends arw initially at…

A: Given, Steel: LS=3 m=3000 mmAS=300 mm2ES=200 GPa=200×103 MPa Aluminum: LAl=6 m=6000 mmEAl=70…

Q: A ball (100 kg) is supported by hollow cylindrical wires, A, B and O as shown in Figure 4. If all…

Q: A 6" diameter pulley attached to a 1" diameter shaft of 2" length is supporting a load of 2000 lb.…

Q: steel:210000 E (MPa) copper:100000 E (MPa) L4 (cm)= 280 L5 (cm)= 255 P1(kN)= 220 P2(kN)= 76 In…

Q: 3. A mild steel rod supports a tensile load of 50 kN. If the stress in the rod is limited to 100…

A: Given Data: Tensile load, P=50 kN Stress, σ=100 MPa

Q: For the punching operation shown in the figure, compute the shear stress (in GPa) in the material if…

A: GivenP=5500kNt=1.5mm=0.0015md=15mm=0.015mL=20mm=0.020m

Q: A steam engine cylinder has an effective diameter of 35 cm and the maximum steam pressure acting on…

Q: 103. Determine the largest weight W which can be supported by the two wires shown in Fig. P-103. The…

Q: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure.…

A: Consider the Free Body Diagram: Force acting on Bronze rod:FCD=2PStress in Bronze…

Q: a) Figure Q2a shows a hollow tube of rectangular cross-section subjected to an axial compressive…

Q: 3. Two steel rods and one copper rod each of 20 mm diameter together support a load of 50 kN as…

Q: The stresses at a point on the surface of a generator shaft are ox = -50 MPa, ơy = 30 MPa and Txy =…

Q: A steel cable of diameter 4.75 mm is attached to an eyebolt and tensioned to 2.25 kN (Figure P5.4).…

Q: The assembly in Figure below consists of a light rigid bar AB, pinned at O, that is attached to the…

A: Given:AB=0.75mOB=1.5m∆=5mmFor steelAst=250mm2E=200 GPaFor aluminiumL=BC=2mAal=300mm2E=70 GPaTo find…

Q: For question 103A and 103B, the thin-walled cylindrical container shown below. Say p is the internal…

A: Internal pressure P=15 MPa Inside diameter d=20 mm Wall thickness t=10 mm Longitudinal stress in a…

Q: Figure Q5 shows a thick cylinder of 50 mm internal radius and 130 mm outer radius is subjected to an…

A: 2 Given: The internal radius, ri = 50 mm The outer radius, ro = 130 mm The internal pressure, Pi =…

Q: piece of wood, 84 mm by 180 mm, is used as a compression block. The grain of the wood makes a 21.2º…

Q: The solid rod shown in the figure below has radius of 0.63 in. If it is subjected to the force of…

Q: Question 3 A Sign is supported by a pole of hollow circular cross section as shown in Figure Q3 The…

A: Calculate the force due to wind.

Q: Determine the largest weight W that can be supported by two wires shown in figure below. The stress…

A: Given data: Max stress=30 ksiAAB=0.4 in2AAC=0.5 in2 Need to determine the largest weight W that can…

Q: 1. The homogeneous bar shown in Fig. P-106 is supported by a smooth pin at C and a cable that runs…

A: Given Weight, W = 40 kN Diameter, d = 25 mm = 0.025 m Length, AB = 4 m…

Q: 2. A shaft 30 mm diameter is transmitting power at a maximum shear stress of 80 MPa. If a pulley is…

A: Given data:

Q: Question 2 a) Figure Q2a shows a hollow tube of rectangular cross-section subjected to an axial…

Q: If a pipe with an inner diameter of 36 mm is subjected to an axial load of 5.20 x 105 N and the…

A: given data dia (d) = 36mm load = 5.20 * 105 N presure (P) = 5.20×105π4×0.0362 allowable stress = σ…

Q: Q2 A steel bar of cross-sectional area 200 mm² is loaded as shown in Fig. Find the change in length…

Q: 1.5 Figure 1.9 shows a circular steel rod of length 40 m and diameter 8 mm, which hangs in a mine…

Q: Calculate the largest weight W that can be attached to the two wires shown in Figure P-103. The…

Q: A 2.4 diameter steel molding is lifted by 4 steel cables as shown. The mold weighs 3 kN/m. (a) what…

A: Given data

Q: Q1/ (A) - The mechanism of femur bone is approximated as a circular tube (3 cm and 2 cm are the…

Q: A crane hook shown in figure below is made of 30 mm diameter steel rod. The distance between the…

A: To find: The load F so that the maximum stress in the rod is not exceed 40 Nmm2. Given: The diameter…

Q: Problem 2.3 A machine bracket is loaded with an inclined force of 1000 N as shown in the figure…

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

A: The Answer is Below

Q: A tractor weighing 80 kN was lifted by 3 cables as shown in the figure. Calculate the stress on the…

A: Given: W=Mg = 80 kN The given system will have four forces to be in equilibrium. The equilibrium…

Q: The bar ABCD in Fig. (a) consists of three cylindrical steel segments with different lengths and…

Q: 1. Find the tensile stress in MPa in member AB shown in the figure. All connection bars have square…

Q: 1.16 The 1000-kg uniform bar AB is suspended from two cables AC and BD, each with cross-sectional…

A: Determine the tension in the rod BD.

Q: For the figure shown, if the tensile force in member AB is 38 kN and the ........ allowable stress…

A: Given:TAB=38 KNσallow=120 MPa

Q: Q1. The clamp shown in the figure applies a force P on the wooden blocks. It ismade of an alloy with…

Question

I need the answer as soon as possible

Calculate the largest weight W that can be attached to the two
wires shown in Figure P-103. The stresses in wires AB and AC
are no more than Mpa 100 and Mpa 150 respectively, knowing
that the cross-sectional area of wire AB is 400 square
millimeters and for wire AC is 200 square millimeters. Answer
W = 33.5 kN
%3D
C
30°
A
45°
W

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in the figure. The roof load P:equals 400 KN, and the second-floor load P-, equals 720 kN. Each column has a length L = 3.75 m. The cross-sectional areas of the first- and second-floor columns are 11,000 mm" and 3900 mm", respectively. (a) Assuming that E = 206 GPa. determine the total shortenings aof the two columns due to the combined action of the loads Ptand P,. (b) How much additional load P0can be placed at t he top of t he column (point C) if t he total shortening: SACis not to exceed 4.0 mm?
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
A pressurized circular cylinder has a sealed cover plate fastened with steel bolts (see figure). The pressure P of the gas in the cylinder is290psi, the inside diameter D of the cylinder is 10.0 in., and the diameter dBof the bolts is 0.50 in. I f the allowable tensile stress in the bolts is 10,000 psi, find the number n of bolts needed to fasten the cover.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
A metal bar AB of a weight Ills suspended by a system of steel wires arranged as shown in the figure. The diameter of the wires is 5/64 in., and the yield stress of the steel is 65 ksi. Determine the maximum permissible weight W max for a factor of safety of 1.9 with respect to yielding.
The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.
A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN. as shown in the figure. The cable has an effective modulus of elasticity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, that is the factor of safety with respect to failure of the cable?
A prismatic bar with a length L = 3 ft and cross-sectional area A = 8 in2 is compressed by an axial centroidal load P = 10 kips. Determine the complete state of stress acting on an inclined section pq that is cut through the bar at an angle W = 35", and show the stresses on a properly oriented stress element.
A hollow circular tube T of a length L = 15 in. is uniformly compressed by a force P acting through a rigid plate (see figure). The outside and inside diameters of the tube are 3.0 and 2.75 in., respectively. A concentric solid circular bar B of 1.5 in. diameter is mounted inside the lube. When no load is present, there is a clearance c = 0.0I0 in. between the bar B and the rigid plate. Both bar and tube are made of steel having an c[autoplastic stress-strain diagram with E = 29 X LO3 ksi and err= 36 ksi. (a) Determine the yield load Pt- and the corresponding shortening 3yof the lube. (b) Determine the plastic load Ppand the corresponding shortening Spof the tube. (c) Construct a load-displacement diagram showing the load Pas ordinate and the shortening 5 of the tube as abscissa. Hint: The load-displacement diagram is not a single straight line in the region 0 ^ P ^ Pr
A prismatic bar with a length L = 1 m and cross-sectional area A = 1200 mm2 is supported at the ends. The bar is then subjected to a temperature increase ?T = 25°C. Calculate the complete stale of stress acting on an inclined section .rs that is cut through the bar at an angle ?? = 45*. Use E = 200 GPa and the coefficient of thermal expansion a = 12×10-6/?.