Calculate the power output from the turbine. Assume the process is adiabatic.Calculate the heat transfer in the economizer and the boiler 1. Consider the following schematic of a power plant (operating in what is called a'Rankine Cycle')TurbineSteamgeneratorCondenserColing waterEconomiaerThe power plant control room reports that the plant is operating continuously at the followingpeak load conditions:a. Power to pump = 300KWb. Rate of steam flow = 25 kg/sc. Cooling water temperature at condenser inlet = 13 Cd. Cooling water temperature at condenser outlet = 34 CAdditionally, the following measurements were made at various points in the piping connectingthe power plant componentsData Pressure Temp. Quality enthalpy Specific Velocity(kJ/kg)point (kPa)volume (m/s)(m3/kg)(C)(x)1620026100435900177----4.5700493-----55500482-----61030.9418379643-----

Answered: Image /qna-images/answer/c47b9528-ff8c-4331-ab7e-02b1328401ae.jpg

Answered: Calculate the power output from the…

Calculate the power output from the turbine. Assume the process is adiabatic. Calculate the heat transfer in the economizer and the boiler

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A dual-pressure combined-cycle power plant consists of a gas turbine,HRSG, and steam turbine plant. The gas turbine exhaust gas flow rate is590 kg/s, temperature is 608°C, HP superheated steam condition is 140bars and 550°C temperature, LP saturated steam is at 8 bar, condenserpressure is 0.05 bar, and feedwater temperature is 120°C. Assuming apinch point of 11 K for both high and low pressure, an exhaust gas specific heat of 1.05 kJ/(kg K), and an isentropic efficiency of the steamturbine of 0.9, calculate (a) the total steam production rate of the HRSG inkg/s, (b) the HRSG heat transfer rate in kJ/s, (c) the stack gas temperaturein °C, and (d) the steam turbine power output in kW.
Solve the MCQ Consider a simple ideal Rankine cycle with fixed turbine inlet conditions. What is the effect of lowering the condenser pressure on the steam quality at the turbine exit a. Incroase b. Decrease c. Remain the same 2. All radiations in a black body are a. Reflected b. Absorbed c. Transmitted 3. Overall heat transfer coefficient is used for heat transfer problems that include a. Radiation b. Convection c. Conduction and convection 4. A grey body is one whose absorptivity a. varies with temperature b. varies with wavelength of the incident radiation c. equal to its emissivity 5. In a heat exchange, doubling the mass flowrate of a fluid while leaving everything unchanged the temperature change of that fluid will a. decreases by 50% b. increase by 50% c. increases by 100% 6. If a heat exchanger LMTD is zero then heat transfer surface become a. Maximum b. Minimum c. Infinity 7. During stagnation process, kinetic energy of the fluid is converted to a. Enthalpy b. Entropy…
A steam-powered power plant works on the basic Rankine cycle.shown in the figure. Likewise, some of its thermodynamic states are summarized in the attached table.Knowing that the work per unit mass delivered to the pump is 3W4 = 2480 (J/kg], determinein SI units the following: a) The specific volume of water in state 4.b) The associated work per unit mass, developed in the Curbina.c) The associated heat per unit mass released by the water in the condenser.d) The efficiency of the cycle
A single-pressure combined-cycle power plant consisting of a gas turbine, HRSG, and steam turbine plant. The gas turbine exhaust gas flow rate is 600 kg/s, temperature is 600°C, live steam condition is 70 bar/500°C, condenser pressure is 0.04 bar, and feedwater temperature is 140°C. Assuming a pinch point of 12 K for both high and low pressure, an exhaust gas specific heat of 1.05 kJ/(kg K), and an isentropic efficiency of the steam turbine of 0.9, calculate: (a) the rate of steam production in kg/s, (b) the stack gas temperature in °C, (c) the steam turbine power output in MW, and (d) the heat transfer rate in the HRSG in kJ/s.
Q#1. A gas-turbine plant operates on the regenerative Brayton cycle, the schematic diagram of whichis shown in Fig. Q 1, with two stages of reheating and two-stages of intercooling between the pressure limits of100 and1200 kPa . The working fluid is air. The air enters the first and the second stages of the compressor at 300 K and 350 K , respectively, and the first and the second stages of the turbine at 1400 K and 1300 K , respectively. Assuming both the compressor and the turbine have an isentropic efficiency of 80%. The regenerator has an effectiveness ofεregen=75% . Assume variable specific heats (i.e., use the concept of relative pressures) and the intermediate pressuresof intercooling and reheating is the square root of the product of inlet and exit pressures for intercooling and reheating. Make other the necessary assumptions and determine(a) the back work ratio,β , and the net work output,, wnet(b) the thermal efficiency (that is the first-law efficiency,ηi ) and(c) the…
A dry steam geothermal power plant is operating on the Rankine cycle under the following conditions:• Plant electric power output Pel = 64 MW• Dry saturated steam pressure at the turbine inlet p1 = 40 bars• Pressure and dryness fraction of wet saturated steam at turbine exit: p2 = 0.05 bar and x2s = 0.7 (after isentropic expansion)• Direct contact condenser pressure p2 = 0.05 bar• Turbine isentropic efficiency ηit = 0.92• Combined mechanical and electrical efficiency of turbine–generator ηtg = 0.96• Plant capacity factor CF = 0.95 Calculate: (a) the plant net specific work, (b) the plant thermal efficiency, (c) the plant overall (electrical) efficiency, (d) the plant steam rate, (e) the plant annual power generation, and (e) the plant rate of heat rejection. Ignore work of the feed pump.
Q2/ Actual Rankine cycle, has the following specifications: Boiler pressure is 160 bar and Turbine inlet temperature is 600 Co and Condenser pressure is 0.08 bar , Turbine efficiency is 0.9 and Pump efficiency is 0.85 and Steam mass flow rate is 130 kg/s Calculate: 1-Work net (kW). 2-heat addition (kW) 3-thermal efficiency.
A superheat steam Rankine cycle has turbine inlet conditions of 10 Mpa and 500 C expands in a turbine to 0.010 Mpa. The turbine and pump polytropic efficiencies are 0.9 and 0.7 respectively pressure losses between pump and turbine inlet are 1.5 Mpa . Determine the following: A.)quality after turbine expansion B.) Turbine work C.)heat added in the boiler D.)heat rejected from the condenser E.)pump work F.) Net work G.)Cycle efficiency
1.5An ideal Rankine cycle with reheat uses water as the working fluid. As shown in the figure below, the conditions at the inlet to the first turbine stage are 1600 lbf/in.2, 1200°F and the steam is reheated to a temperature of T3 = 800°F between the turbine stages at a pressure of p3 = p2 = 200 lbf/in.2 For a condenser pressure of p5 = p4 = 1 lbf/in.2, determine:(a) the quality of the steam at the second-stage turbine exit. h6≈h5+v5(p6−p5)h6≈h5+v5(p6-p5)Determine the quality of the steam at the second-stage turbine exit. x4 =(b) the cycle percent thermal efficiency.
A steam-powered power plant works on the basic Rankine cycle.shown in the figure. Likewise, some of its thermodynamic states are summarized in the attached table.Knowing that the work per unit mass delivered to the pump is ›W = 2480 (J/kg], determinein SI units the following: a) The specific volume of water in state 4.b) The associated work per unit mass, developed in the Curbina.c) The associated heat per unit mass released by the water in the condenser.d) The efficiency of the cycle
A 272-MW steam power plant operates on the Rankine cycle but with turbine and pump efficiencies of 90%. The steam enters the turbine at 10,000 kPa and 550°C. It discharges to the condenser at 50 kPa. Determine the mass flow rate in kg/s.?
1. A Rankine cycle with reheating has a throttle pressure of 135 bars at the turbine inlet and 28 bars reheatpressure, the throttle and reheat temperature of the steam is 550C, condenser pressure is 0.035 bar, massflow rate of steam is 10 kg/sec. Draw the T-s and schematic diagram of the cycle and determine the following:(a) ideal turbine work(b) ideal pump work(c) theoretical thermal efficiency(d) the steam rate(e) heat rate of the cycle(f) actual work of the pump if pump isentropicefficiency is 89%(g) actual turbine work if turbine isentropic efficiencyis 90%