Calculate the vertical displacement (downward) at Joint C of the given truss shown in Figure 2 using the method of virtual work. You can use Space Gass to Calculate the internal forces of the real and virtual systems without manual calculations. Assume the cross-sectional area and modulus of elasticity of each member are constant. H Al B 3 kN 4 m ++ 4 m G 4 kN 4 m Figure 2 D 3 kN + 4 m 1 E 3 m

Calculate the vertical displacement (downward) at Joint C of the given truss shown in Figure 2 using the method of virtual work. You can use Space Gass to Calculate the internal forces of the real and virtual systems without manual calculations. Assume the cross-sectional area and modulus of elasticity of each member are constant. H Al B 3 kN 4 m ++ 4 m G 4 kN 4 m Figure 2 D 3 kN + 4 m 1 E 3 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the vertical displacement (downward) at Joint C of the given truss using the method of virtual work. You can use Space Gass to compute the internal forces of the real and virtual systems without manual calculations. (Assume the cross-sectional area and modulus of elasticity of each member are constant.)
Determine the horizontal component of the force applied by the smooth circular guide on the mass A. mA = 2 kg, y= 100 mm, Vy = 0.6 m/s, ay = -0.2 m/s^2
Determine the bending moment at B. if w =39 kN/m, L =8Round off the final answer to three decimal places.
5. What is the approximate moment at support a? In kN.m A. -79.86 B. -27.95 C. -73.28 D. 0 E. -10.98 F. 73.28 G. 79.86 H. 10.98 I. 27.95
calculate the Axial Force in kips on member BC if the given 30kip and 20kip loads from the figure are both replaced by 42kips and 45kips respectively. Express your answer in 2 decimal places. Include (-) negative sign if the axial force is compression.
For the frame shown, determine the support reactions. EI is constant.Use the force method. I have a correct answer, it is: VA = 36.30 kN (↑); HA = 19.30 kN (→); VB = 18.70 kN (↑); HB = 11.30 kN (←). To the left); B (right). I don't know how to get to this result, please show me how to get there step by step
In the overhanging beam show, determine P so that the moment over each support equals the moment at the midspan. W= 3.7 kN/m. Round your answer to 2 decimal places.
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. Note that: a = 3.7 m b = 31.0 kN/m c = 35 kN Find the ff. A. Vertical reaction at B in kN. B. Moment reaction at A in kN-m. C. Deflection at point C in mm. D. Deflection at midspan of AB in mm.
(G) Using these results (δ1=0.1097 in. , δ2=0.1265 in. , δ3=0.0548 in.) determine the deflections of Joint B and Point D. ANSWERS in inch (H) On a piece of paper, sketch a free body diagram (FBD) cut through rod (3) and also a FBD of the rigid bar. Using these, find a relationship between the force in rod 1 (F1) and the applied load, P, a relationship between the force in rod 2 (F2) and the applied load, P, and also a relationship between the force in rod 3 (F3) and the applied load, P. (I) Based on the allowable stress for the bronze, calculate the maximum allowable force that can be supported by rod (1), and the corresponding maximum value for the applied load P. IN KIPS (J) Based on the allowable stress for the aluminum, calculate the maximum allowable force that can be supported by rod (2) and rod 3, and the corresponding maximum value for the applied load P. IN KIPS (K) Using the results from Part 8, determine the deflections of Joint B and Point D. IN INCH NOTE: These are the…
Beam ABC is fixed at support A and rests(at point B) upon the midpoint of beam DE (see partaof the gure). Thus, beam ABC may be representedas a propped cantilever beam with an overhang BCand a linearly elastic support of stiffness k at point B(see part b of the figure).The distance from A to B is L =10 ft, the distancefrom B to C is L/2 = 5 ft, and the length of beamDE is L =10 ft. Both beams have the same flexuralrigidity EI. A concentrated load P =1700 lb acts atthe free end of beam ABC.Determine the reactions RA, RB, and MA for beamABC. Also, draw the shear-force and bending-momentdiagrams for beam ABC, labeling all critical ordinates.
The 300-lb force is to be resolved into components along lines a-a’ and b-b’. 1. Determine the angle α knowing that the component along line a-a’ is 240-lb. 2. What is the corresponding value of force along line b-b’?
Determine the axial force in member DE in kN. Use F1 = 77 kN, F2 = 60 kN, x = 3.65 meters, y = 3.24 meters. Round off to two decimal places. Input the numerical value only.