Component B is separated by dissolution in water, followed by filtration. the filtrate is collected in a beaker weighting 96.47g . After evaporation of the water from the filtrate , the beaker and solid residue weight 97.25g. What is the weight of of component B ? Calculate the weight percent of component B in the original mixture.

Component B is separated by dissolution in water, followed by filtration. the filtrate is collected in a beaker weighting 96.47g . After evaporation of the water from the filtrate , the beaker and solid residue weight 97.25g. What is the weight of of component B ? Calculate the weight percent of component B in the original mixture.

EBK A SMALL SCALE APPROACH TO ORGANIC L

4th Edition

ISBN:9781305446021

Author:Lampman

Publisher:Lampman

Chapter13: Isolation Of Eugenol From Clov

Section: Chapter Questions

Problem 9Q

See similar textbooks

Similar questions

You have been tasked with determining the wastewater solids generated by a community. To determine solids, you collect two effluent samples of 100 mL each. The first sample was placed, unfiltered, in a crucible and dried at 105 ̊C overnight. The weight of the dried sample and crucible was 5.6112 g, while the weight of the crucible was 5.6000 g. The second sample was filtered. The filter and drying dish were dried overnight at 105 ̊C after which they weighed 2.1085 g. The filter and drying dish were then placed in a muffle furnace at 550 ̊C for 30 mins, after which they weighed 2.103 g. The drying dish weighs 1.6000 g and the filter weighs 0.5 g. a) Determine the concentration of TS, TSS, VSS, FSS and TDS in mg/L: b) Does TSS concentration meet the federal effluent regulations? If not, what removal techniques would you recommend and what minimum percent must be removed prior to discharge?
A mixture of methanol and water contains 60.0% water by mass. Assuming volume additivity: If the actual specific gravity of the mixture is 0.9345: How many liters is required to provide 150 mol of methanol?
An evaporation-crystallization process is used to obtain solid potassium sulfate from an aqueous solution of this salt. The fresh feed to the process contains 19.6% wt K2SO4 The wet filter cake consists of solid K2SO4 crystals and 40 % wt K2SO4 solution, in a ratio 10 kg crystals/kg solution. The filte a 40% solution is recycled to join the fresh food. Of the water fed to the evaporator, 45% is evaporated The evaporator has a maximum capacity of 175 kg/hr water evaporales Calculate a) The maximam production rate of solid K2SO4 b) The rate at which fresh feed must be supplied to achieve this production rate c) The ratio kg recycle kg fresh feed
The mass of a beaker is 5.333g. After 5.00mL of a concentrated hydrochloric acid solution is pipetted into the beaker, the combined mass of the beaker and the hydrochloric acid sample is 11.229g. From the data, what is the measured density of the hydrochloric acid solution?
The mass of the original mixture was 2.03g. The combined mass of the salt and the evaporating dish was 48.92g with the tare mass of the evaporating dish being 47.98g. The combined mass of the sand and watch glass and filter paper was 32.15g with the tare mass of the watch glass being 30.91g and of the filter paper being 0.28g. A) calculate the percent of table salt in the recovered material. B) calculate the percent table salt in the original mixture
When concentrated nitric is sold, the label contains no mention of the molarity of the acid. Instead, the label normally lists the concentration of nitric acid as a wt/wt percent and gives the specific gravity of the solution. If the solution is 68.0 (wt/wt %) and nitric acid and has a specific gravity of 1.41 kg/L, calculate the molarity of 68.0 % concentrated nitric acid. FW HNO3=63.01g/mol
The reaction of solid calcium fluoride and sulfuric acid produces calcium sulfate solids and gaseous HF. The gas product is dissolved in water to form hydrofluoric acid. Fluorite ore, a source of calcium fluoride, contains 95%wt CaF2 and 5%wt SiO2. In a certain process, the ore is reacted with 93%wt aqueous sulfuric acid, supplied 15% in excess. From this, 95% of the ore dissolves in the acid. Some of the HF formed reacts with the dissolved silica in the reaction: HF reacts with SiO2 to produce H2SiF6 and liquid water. If 60%wt of hydrofluoric acid was formed when hydrogen fluoride (which exits the reactor) is dissolved in water, determine the amount of ore needed to produce one metric ton of acid. Report your answers to one decimal place only.
Stock iron(II) solution (200Ug mL-1 Fe) ferrous ammonium sulfate hexahydrate mass= 0.1437g, transfer it to a 100 ml beaker. add 15 ml approx of water and 15m1 'approx of dilute sulphuric acid (2M H2SO.). then transfer FeII to 100 ml flask makeup to the mark with water. calculate the moles of ferrous ammonium sulfate hexahydrate solution in unit ug/mL.
A multiple effect evaporator has a capacity to process 10000 kg of solid caustic soda per day, when it is concentrating from 3% to 40% solids. The water evaporated in kg per day is _________________
Calculate the percent composition of sand in the mixture using the mass of the recovered sandCalculate the theoretical mass of salt in the mixtue using the mass of the recovered sandCalculate the theoretial percent composition of salt in the mixtureCalculate the percent error for the recovered saltCalculate the total mass of the recovered solids Weight of mixture: 1.841Weight of salt: 1.319Weight of sand: 0.376Weight of sand after heating: 0.376
93.6g to ng and 93.6g to tons with the set up in the image possible show how to get the answer please
What is the molarity of a concentrated solution of sulfuric acid with a specific gravity of 1.84 and 95.0% by weight sulfuric acid? specific gravity = density of substance at certain temp/density of water at 4 degrees C the density of water is 0.999973 g/mL at 4 degrees celsius. Describe how to prepare 3.0 L of 0.100M. I will pipet ______ and add this to 200mL water. The solution will be stirred and diluted to 3L with water.