Compute the gallons of sealer required to seal a floor 120'x250'. The sealer being used will cover 175ft2 per gallon

Q: te the lonic King F

A:

Q: n end force of 15 kN inc rot or go

A:

Q: 2Pi KL(Tin-Tout) Q = In- Ri

A:

Q: e diameter

A: To find Outside diameter(d2)

Q: Compute the lead angle of a 1/4-6 UNC single thread

A: Fo 1/4-6 UNC thread the major diameter of thread and pitch are, D=40.2 mm, pitch = 4.5 mm Write the…

Q: A metal disc of 50 mm diameter is to be punched from a sheet of 5 mm thickness. The punch and the…

A: Given that Disc diameter = 50mm Clearence = 3% = 0.03

Q: Poisson's ratio of the rod

A: Given; Find Poisson's ratio of the rod material ?Where,  Metallic rod length, l=500 mmDia,d=50…

Q: veld can sustain is (kN m)

A:

Q: Find the standard distance between sprocket having 4 in and 16 in diameters.

A:

Q: 01/ Give the dimensions for the hole and shaft for the 12 mm electric motor sleeve bearing (pump);

A: Given:Basic size given for motor sleeve bearing=12 mm

Q: y 4x I 2ft y 2r 1 ft- For D

A:

Q: 04/ Determine suitable groove dimensions for a 0101-16 '0' ring to seal against a solid cylinder.

A: Given that ,  Determine suitable groove dimension for a 0101-16 'O' ring to steal against a solid…

Q: eaga (w)=1 rade\s counter cloch

A:

Q: The nominal diameter of V00 bolt is diameter. If safe tensile stres of the bolt

A:

Q: What is the magnitude of the force on the structural member EF in kips?

A: Since, point A is a hinge support. So, at point a two reactions will act. RAV = Reaction force in…

Q: en expanded isothe nally compressed a to the init

A:

Q: ch of 6 mm. Th d collar friction

A:

Q: Solve for the magnitude of the vertical and horizontal forces on each joint using all the possible…

A: To find magnitude of force in each joint

Q: ic, calculate the heat loss from the rod.

A: To find the heat loss from the rod.

Q: 2. A punch press has punches forty (40) circlesbat are 2 inches in diameter through medium carbon…

A:

Q: please explain for c) what is Sum of M at hinge

A:

Q: dimension L4 in mm for assembly condition would be:

A: For the given assembly: L1=22.0±0.01 mm L2=10.0±0.005 mm L3=10.0±0.005 mm It is required to…

Q: (8 – x) . 5 in. Dy -2 in.

A:

Q: n'. CALCULATE the number of friction plate required.

A:

Q: Four inch schedule 80 steel pipes are used to transport high pressure steam. The pipe joints are to…

A: Given Data⇒ Diameter of steel pipe(D)=4 inch  D=10.16 cm Safe working stress is σall=550kgcm2…

Q: Required : 1. Determine the safest thickness of the vessel in mm 2. If the vessel has spherical…

A:

Q: Solve for FEF, FDF and FGI

A:

Q: ch. The friction lining has a ce 25. The bore radius of friction li ilom contLacl pressur of IMI

A:

Q: A circular duct is to measure 20.5 centimeters in diameter and 75 centimeterslong. It has a butt…

A: Given Data  Circular diameter of the duct, D=20.5 cm The radius of the duct, r=d/2=20.5/2=10.25cm…

Q: - number of teeth ower of 3 kW at 2

A:

Q: 1) The working face of ordinary flat key is 1 A. Side B. Upper top surface C. Bottom surface D. End…

A: (1)

Q: SoNe for a minímum bolt diameter minimum thickness of plate the rivets are atfached to Given: wad =…

A:

Q: What is the magnitude of the force on the structural member BC in kips?

A: The figure below represents the components of force acting on the members.   As triangle CDF is…

Q: (a) Find Depth of cut and Root diameter for M18 x 2.75 x 30 internal thread.

A: Given:- M18 x 2.75 x 30   To find:- Depth of cut Root diameter

Q: should be the wall thickness am teel with a design factor of 3 the wall thickness and weight

A:

Q: Draw sectional front view only of a double riveted zigzag lap joint to join two plates of thickness…

A: Given: Draw sectional front view only of a double riveted zigzag lap joint to join two plates of…

Q: The straight surface on either side of the screw thread is known as Flank Root Crest Pitch

A:

Q: ety, the maximum ne rod is limited to st be at least 1000

A: Load on the steel rod = 50 tones  = 50×1000 =50000 kg Allowable stress =150kg/mm2 Allowing stress=…

Q: ow bar evaluate use th

A:

Q: X -2 ft- F By 2 ft F P 2 ft

A: As per honor code and answering guidelines I can answer 1st 3 subparts at a time.If you want other…

Q: List the more common seal configurations and draw their cross sections.

A: Some of the common seal configurations are : Rod seal Piston seal Face seal

Q: rigid flange coupling

A: Mt=228 Nm=228000Nmm Diameter of shaft τ=16Mtπd3100=16*228000πd3d=22.645 mm or 25 mm

Q: The maximum radial load it can sustain

A: Given; The dynamic laod capacity of 6306 bearing Load=20kNThe maximum radial load?Rotation=650…

Q: is 10 min short- dia 3 mm. Finds es hy o'mpress by 20

A:

Q: Compute the lead angle of an M16 × 1 double thread.

A:

Q: Give 5 examples of jobs where sealant and adhesive can be applied or used.

A: 5 examples of jobs where sealant and adhesive can be applied or used

Q: problem

A: Given:S=6000lb/in2=864000lb/ft2W=490 ln/ft2A=2 in2=.0139 ft2L=1000ft…

Q: A metric thread of pitch 2 mm and thread angle 60° is inspected for its pitch diameter using 3 wire…

A: Given:Pitch, P=2 mmThread angle, 2θ=60oθ=30o

Corrosion control methods

Corrosion may be defined as the method in which metals are attacked on their exteriors by gases existing in the atmosphere, converting them to their oxides, nitrides, sulfides, etc.