Consider a wire of some material whose Young's modulus under tensile and compressive stress is identical. When a pressure P is applied at both ends to stretch the wire, its final length is 2.15[m]. When an identical pressure P is applied at both ends to squeeze the wire, its final length is 1.98[m]. Calculate the equilibrium length of the wire.

Consider a wire of some material whose Young's modulus under tensile and compressive stress is identical. When a pressure P is applied at both ends to stretch the wire, its final length is 2.15[m]. When an identical pressure P is applied at both ends to squeeze the wire, its final length is 1.98[m]. Calculate the equilibrium length of the wire.

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 47PQ

See similar textbooks

Similar questions

A uniform wire (Y = 2.0 1011 N/m2) is subjected to a longitudinal tensile stress of 4.0 107 N/m2. What is the fractional change in the length of the wire?
A copper rod with length 1.4 m and cross-sectional area 2.0 cm2 is fastened to a steel rod of length L and cross-sectional area 1.0 cm2. The compound structure is pulled on each side by two forces of equal magnitude 6.00 104 N (Fig. P14.57). Find the length L of the steel rod if the elongations (L) of the two rods are equal. Use the values Ysteel = 2.0 1011 Pa and YCu = 1.1 1011 Pa. FIGURE P14.57
The lintel of prestressed reinforced concrete in Figure P12.27 is 1.50 m long. The concrete encloses one steel reinforcing rod with cross-sectional area 1.50 cm2. The rod joins two strong end plates. The cross-sectional area of the concrete perpendicular to the rod is 50.0 cm2. Youngs modulus for the concrete is 30.0 109 N/m2. After the concrete cures and the original tension T1 in the rod is released, the concrete is to be under compressive stress 8.00 106 N/m2. (a) By what distance will the rod compress the concrete when the original tension in the rod is released? (b) What is the new tension T2 in the rod? (c) The rod will then be how much longer than its unstressed length? (d) When the concrete was poured, the rod should have been stretched by what extension distance from its unstressed length? (e) Find the required original tension T1 in the rod. Figure P12.27
An aluminium (=2.7g/cm3) wire is suspended from the ceiling and hangs vertically. How long must the wire be before the stress at its upper end reaches the proportionality limit, which is 8.0107N/m2 ?
Normal forces of magnitude 1.0106N are applied uniformly to a spherical surface enclosing a volume of a liquid. This causes the radius of the surface to decrease from 50.000 cm to 49.995 cm. What is the bulk modulus of the liquid?
Two rods, one made of copper and the other of steel, have the same dimensions. If the copper rod stretches by 0.15mm under some stress, how much does the steel rod stretch under the same stress?
A horizontal, rigid bar of negligible weight is fixed against a vertical wall at one end and supported by a vertical string at the other end. The bar has a length of 50.0 cm and is used to support a hanging block of weight 400.0 N from a point 30.0 cm from the wall as shown in Figure P14.81. The string is made from a material with a tensile strength of 1.2 108 N/m2. Determine the largest diameter of the string for which it would still break. FIGURE P14.81
Can Young’s modulus have a negative value? What about the bulk modulus?
Discuss how you might measure the bulk modulus of a liquid.
The face of an aluminum plate, which is fixed in place, measures 90 cm by 90 cm. The thickness of the plate is 6 cm. A force parallel to it, produces a shear strain of 0.0060. The shear modulus of aluminum is 3.0 × 10^10 Pa. Find the displacement of the upper force.
A wire of uniform cross sectional area of 0.15 mm2 is stretched at both ends by a total force of 40 N and the strain produced by the wire is 1 × 10–2 m. Calculate the Young modulus of the material of the wire.
A solid steel sphere with a radius of 2.0 m falls off a ship and sinks to a depth where the pressure is 15 MN/m2. The bulk modulus for this steel is 1.6 × 1011 N/m2. What is the change in the radius of the sphere?