Answered: Consider laminar flow of air across a…

Consider laminar flow of air across a hot circular cylinder. At what point on the cylinder will the heat transfer be highest? What would your answer be if the flow were turbulent?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.38P

See similar textbooks

Related questions

Q: Q1: Consider a hot automotive engine, which can be approximated as 0.40m wide, and 0.8m long…

A: Given Data The speed of the car is: γ=80 km/h=22.22 m/s The length of the engine block is: L=0.8 m…

Q: rite the definition ,formula and significance of Reynolds number and Grashoff number in convection…

A: Given: Reynolds number Grashoff number To write: The formula, definition and significance of in…

Q: Q) Water at 22'C flows in a 40-cm-diameter pipe and 25-m-long at an average velocity of 0.15 m/s.…

Q: What is natural convection? How does it differ from forced convection? What force causes natural…

A: Heat transfer can take place in three different modes namely conduction, convection and radiation.…

Q: 1- Air at 288.8 k and 101.32 kPa with a free stream velocity of 3.05 m/s is flowing parallel to a…

A: Given:

Q: Q3: Air flows across a 20-cm-square plate with a velocity of 5 m/s. Free-stream conditions are 10 C…

A: In general, there are three modes by which heat gets transferred from one place to another. The…

Q: A long 10-cm-diameter steam pipe whose external surface temperature is 110°C passes through some…

A: In order to proceed with the problems some assumptions need to be considered. Steady operating…

Q: What happens to the heat transfer coefficient in convection heat transfer if the viscosity of the…

A: Viscosity: The resistance to flow of any fluid is known as viscosity. The viscosity of any fluid is…

Q: Glycerin is being heated by flowing between two parallel 1-m-wide and 10-m-long plates with 12.5-mm…

A: Given: The width of the plate, w = 1 m The length of the plate, L = 10 m The spacing of plates, t =…

Q: What does the friction coefficient represent in flow over a flat plate? How is it related to the…

A: Drag force is a force acting on a body (moving or stationary)which is present in a moving or…

Q: During a cold winter day, wind at 55 km/h is blowing parallel to a 4m high and 10m long wall of a…

Q: Hot engine oil at 150°C is flowing in parallel over a flat plate at a velocity of 2 m/s. Surface…

A: Given data Temperature of hot engine oil To = 1500C = 423K Velocity of oil flow V = 2m/s Length of…

Q: Why is heat transfer faster in forced convection compared to natural convection

A: Natural convection: when heat transfer is taking place due to motion of fluid caused by density…

Q: Air at 30 oC flowing over a flat plate 0.5 m long and 0.6 m wide, is to be maintained at 70 oC .…

A: This question is solved with the help of the convection heat transfer coefficient equation. As shown…

Q: Thick fluids such as asphalt and waxes and the pipes in which they flow are often heated in order to…

Q: Air is flowing in parallel over the upper surface of a flat plate with a length of 4 m. The first…

A: The value of kinematic viscosity, v = 1.608×10-5 m2s Thermal conductivity, k = 0.02588 Wm·K Prantl…

Q: Hot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. The gas at 220°C flow is…

Q: What is heat transfer coefficient?

A: The heat transfer constant or film constant, or film effectiveness, in physical science and in…

Q: A long 8-cm-diameter steam pipe whose external surface temperature is 90°C passes through some open…

A: Given data diameter of the pipe D = 8 cm = 0.08m External surface temperature of the pipe Ts = 900C…

Q: Liquid mercury at 250°C is flowing with a velocity of 0.3 m/s in parallel over a 0.1-m-long flat…

A: The data given is, The temperature of liquid Mercury = 250 ℃ The velocity of flow, V = 0.3 m/s…

Q: Hot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates as shown in Fig 3. The gas at…

Q: Engine oil at 83°C flows over the upper surface of a 5-m-long flat plate whose temperature is 18°C…

Q: When is heat transfer through a fluid conduction and when is it convection? For which case is the…

A: The rate of heat transfer is given

Q: What regime favors heat transfer and why? Laminar, Turbulent or Transitional

A: Heat transfer is basically a process in which the molecules are moved from their initial position in…

Q: Consider a hot baked potato. Will the potato cool faster or slower when we blow the warm air com ing…

A: It will cool faster in case of warm air coming from lung.

Q: Air (1 atm) entered into a 5-mm-diameter circular tube at an average velocity of 5 m/s. The tube…

A: Given data, The length of the tube, L = 10 cm The diameter of the tube, d = 5 mm The velocity of…

Q: Consider steady, laminar, two-dimensional flow over a hot plate. Does the convective heat transfer…

A: Given: Consider steady, laminar, two-dimensional flow over a hot plate The wall shear stress is…

Q: what are the different modes of heat transfer? Explain transfer of heat by convection process?

Q: Air is flowing in parallel over the upper surface of a flat plate with a length of 4 m. The first…

A: The velocity of free stream is V=0.5 m/s. The temperature of air is T∞=100C. The kinematic viscosity…

Q: Define and explain the physical significance of the following:(a)prandtl number(b) Reynolds number…

Q: What does the Grashof number represent? How does the Grashof number differ from the Reynolds number?

A: Grashof number is a dimension less number. Which we use in heat transfer and fluid mechanics.

Q: When the convection heat transfer coefficient is very large (h → ∞), the convection resistance…

A: When the convection heat transfer coefficient is very large (h → ∞), the convection resistance…

Q: Q) Water at 22°C flows in a 40-cm-diameter pipe and 25-m-long at an average velocity of 0.15 m/s.…

Q: Consider a person walking first in the air and then in the water at the same speed. Which motion…

Q: Consider a fluid with a Prandtl number of 7 flowing through a smooth circular tube. Using the…

A: Now, consider the value of Reynold’s Number as 3500, the Nusselt numbers are calculated by given…

Q: Consider a refrigeration truck traveling at 55 mph at a location where the air temperature is 80°F.…

A: The data given is, Size of the refrigerated compartment = 9 ⨯ 8 ⨯ 20 = 1440 ft3 Length of…

Question

Consider laminar flow of air across a hot circular
cylinder. At what point on the cylinder will the heat transfer
be highest? What would your answer be if the flow were turbulent?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

5.7 The average Reynolds number for air passing in turbulent flow over a 2-m-long, flat plate is . Under these conditions, the average Nusselt number was found to be equal to 4150. Determine the average heat transfer coefficient for an oil having thermal properties similar to those in Appendix 2, Table 18, at at the same Reynolds number and flowing over the same plate.
7.43 Liquid sodium is to be heated from 500 K to 600 K by passing it at a flow rate of 5.0 kg/s through a 5-cmID tube whose surface is maintained at 620 K. What length of tube is required?
What does the logarithmic mean temperature difference represent for flow in a tube whose surface temperature is constant? Why do we use the logarithmic mean temperature instead of the arithmetic mean temperature?
Liquid mercury at 250°C is flowing with a velocity of 0.3 m/s in parallel over a 0.1-m-long flat plate where there is an unheated starting length of 5 cm. The heated section of the flat plate is maintained at a constant temperature of 50°C. Determine (a) the local convection heat transfer coefficient at the trailing edge, (b) the average convection heat transfer coefficient for the heated section, and (c) the rate of heat transfer per unit width for the heated section.
Consider turbulent forced convection in a circular tube. Will the heat flux be higher near the inlet of the tube or near the exit? Why?
What does the Grashof number represent? How does the Grashof number differ from the Reynolds number?
A 1.2-in-outer-diameter pipe is to span across a river at a 140-ft-wide section while being completely immersed in water. The average flow velocity of the water is 10 ft/s, and its temperature is 70°F. Determine the drag force exerted on the pipe by the river.
What is natural convection? How does it differ from forced convection? What force causes natural convection currents?
When is the heat transfer through a fluid conduction and when is it convection? For which case is the rate of heat transfer higher? How does the convection heat transfer differ from the thermal conductivity of the fluid?
Consider a 25-mm-diameter and 15-m-long smooth tube that is maintained at a constant surface temperature. Fluids enter the tube at 50°C with a mass flow rate of 0.01 kg/s. Determine the tube surface temperatures necessary to heat water, engine oil, and liquid mercury to the desired outlet temperature of 150°C.
. Castor oil at 36 °C flows over a 6 m long and 1 m wide heated plate at 0.06 m/s. For a surfacetemperature of 96 °C, determine (i) the thermal boundary layer thickness at the end of the plate,(ii) the local heat transfer coefficient at the end of the plate, and (iii) the rate of heat transfer fromthe entire plate
Air is flowing in parallel over the upper surface of aflat plate with a length of 4 m. The first half of the plate length,from the leading edge, has a constant surface temperatureof 50°C. The second half of the plate length is subjected toa uniform heat flux of 86 W/m2. The air has a free streamvelocity and temperature of 2 m/s and 10°C, respectively.Determine the local convection heat transfer coefficients at1 m and 3 m from the leading edge. Evaluate the air propertiesat a film temperature of 30°C. Is the film temperatureTf = 30°C applicable at x = 3 m?