Consider the steps involved in preparing a dilute solution from a stock solution. Arrange them in order from first to last. You are currently in a ranking module. Turn off browse mode or quick nav, Tab to move, Space or Enter to pick up, Tab to move items between bins, Arrow Keys to change the order of items, Space or Enter to drop. First Last Answer Bank Add the desired amount of stock solution. Cap the flask and invert several times to thoroughly mix the solution. Add deionized water until the volume reaches the mark on the flask. Obtain a flask that is thoroughly cleaned and dried. If a student accidentally adds deionized water past the calibrated mark on the volumetric flask, he should dump the excess solution until the volume is right at the mark. start over and make an entirely new solution.

Consider the steps involved in preparing a dilute solution from a stock solution. Arrange them in order from first to last. You are currently in a ranking module. Turn off browse mode or quick nav, Tab to move, Space or Enter to pick up, Tab to move items between bins, Arrow Keys to change the order of items, Space or Enter to drop. First Last Answer Bank Add the desired amount of stock solution. Cap the flask and invert several times to thoroughly mix the solution. Add deionized water until the volume reaches the mark on the flask. Obtain a flask that is thoroughly cleaned and dried. If a student accidentally adds deionized water past the calibrated mark on the volumetric flask, he should dump the excess solution until the volume is right at the mark. start over and make an entirely new solution.

Appl Of Ms Excel In Analytical Chemistry

2nd Edition

ISBN:9781285686691

Author:Crouch

Publisher:Crouch

Chapter4: Least-squares And Calibration Methods

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Filter paper can be added to the developing chamber to help saturate the chamber with solvent vapor. Group of answer choices True False
TRUE OR FALSE __________ 11. The minimum number of centrifuge tubes in a centrifuge machine during its operation is one. __________ 12. Never place reagents directly onto the weighing pan of a balance, always use weighing paper, a beaker, or some other container. __________ 13. To transfer a solution, the stirring rod touches the delivery point of the reagent vessel and the wall of the receiving vessel. __________ 14. An open flame is the heat source for heating or evaporating flammable liquids. __________ 15. Most chemicals used in experiments can be discarded into the sink.
Please answer this question as fast as you can please and tahnk you. I will afterwards write an wonderful review on solving the question. Thank you. Why is it important for us to leave the water for 5 minutes and determine the water's temperature? The density of water will vary with temperature. You want the water to equilibrate to room temperature in order to maintain consistent results. You want to wait so that the dissolved solids in the water settle to the bottom of the flask. It is impossible to determine the density of water below 20 °C with plastic beakers and cylinders so you need to wait for the water to warm up. It's not that important, we just want to stretch out the time of the experiment.
Matt was heating his methanol solvent in an E. flask on a hot plate to use for recrystallization. The TAcame by and noticed he didn’t have a stir stick or boiling chip in the flask and told him to use one,please. Matt dropped a stick in the flask and suddenly the liquid exploded out of the flask. Oops! Tellme why that happened. What should he have done instead?
Volumetric pipettes are designed to deliver a precise amount of liquid, but only if you a. submerge the end of the pipette into a solution you are delivering. b. allow the pipette to drain freely, and leave any residual solution in the pipette. c. hold the pipette at a 45 degree angle and ensure that all the liquid is delivered.
Show clear full solutions please and recheck thank you
Chemistry How to increase storage and shelf life of ready to drink bottled sorghum porridge using stabilizers ( state names of stabilizers to use and the amounts to add) or any other ingredients to use so that sedimentation or settling of dispersed particles is prevented without hindering the taste of the porridge so that the porridge can be sold in the market?
A circular lake of diameter 2.5m is receiving wastewater with a flow rate of 25 L/sec from a village has phosphorus concentration of 0.5 mg/L. The lake receives Phosphorus point source concentration of 0.8 g/sec. If the wastewater is completely mixed in the pond and removes phosphorus with a removal rate of 12 m/year, find the concentration of phosphorus (mg/L) in effluent water stream? Assume steady state. (Round-off to one decimal place).
Dilution is done to commercially available acids such as HNO3, H2SO4 etc so that the strength is increased and so it will be safe to be used by students in a chemistry laboratory. Select one: True False
a. Colloidal particles typically have a negative surface charge that attracts oppositely charged positive ions in the surrounding bulk solution. These so-called _______-ions are held at the particle surface through electrostatic and van der Waals forces of attraction strongly enough to overcome thermal agitation. b. Turbine and propeller type mechanical mixers used for rapid mixing of reagent chemicals have either ------------- flow impellers with flat or curved blades located parallel to the axis of the drive shaft, or --------------------- flow impellers with blades making an angle of less than 90o with the drive shaf
DATA Note: Use the videos as references except when data is provided here. Table 1. Selection of Recrystallizing Solvent. Solvents Dissolution at room temperature? (+ or −) Dissolution at elevated temperature? (+ or −) Distilled water - - Acetone + n/a 95% ethanol - + Toluene + n/a Solid sample: Naphthalene Table 2. Mass Measurements. Mass, g Sample solid 0.5021 Empty watch glass 35.7602 Watch glass with recrystallized sample 36.2485 Table 3. Melting Point Determination. Temperature, oC Appearance of Sample in Capillary Tube … Solid 78.4 Solid 79.3 Solid with signs of liquid 79.9 Solid, liquid 80.6 Liquid, solid 81.3 Liquid with signs of solid … Liquid Theoretical Melting Point, oC: 80.2°C (176.4°F) QUESTIONS Which solvent should be used as the recrystallizing solvent? Check if your chosen solvent satisfies all characteristics of a good…
Show Complete solution and diagram please! Thank youu