Consider the truss shown in (Figure 1). Suppose that F= 14 kN. Figure 4 kN 6kN G 6kN C 1.5m-1.5m-1.5m-1.5m- 1 of 1 > Part A Determine the force in member CD and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FCD = Submit Part B FeJ= Submit CH ▾ Part C Value Request Answer Determine the force in member CJ and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. HÅ Value n C Request Answer Units ? Units ? Determine the force in member GJ and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension.

Consider the truss shown in (Figure 1). Suppose that F= 14 kN. Figure 4 kN 6kN G 6kN C 1.5m-1.5m-1.5m-1.5m- 1 of 1 > Part A Determine the force in member CD and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FCD = Submit Part B FeJ= Submit CH ▾ Part C Value Request Answer Determine the force in member CJ and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. HÅ Value n C Request Answer Units ? Units ? Determine the force in member GJ and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Set P1 = 70 kN, P2 = 50 kN. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. a) Determine the force in member CG of the truss. b) Determine the force in member DE of the truss. c) Determine the force in member DF of the truss. d) Determine the force in member EF of the truss. e) Determine the force in member FG of the truss.
If P = 8.571 kN, determine the stress in member CE assuming that the area in steel is 24 mm^2. *DRAW THE FREE BODY DIAGRAM *COMPLETE SOLUTION *3 decimal places ALL ANSWER
For the frame shown, determine the maximum normal stresses (compression and tension) and the maximum shear stress, caused by the acting trapezoidal load. Express your answer in MPa. Sección trasversal means cross section.
Determine the largest force P (kN), directed as shown in the figure that can be applied to the bracket if the allowable normal stresses on section A-B are 8 Mpa in tension and12 Mpa in compression. A119.15 B.79.44 C.18.64 d.14.31 answer:14.31
For the beam shown, determine the support reactions and draw the stress diagrams.shear and bending moment. EI is constant. Use the force method. I have a correct answer, it is: VA = 44.3 kN (↑); HA = 0 kN; MA = 34.3 kN.m (counterclockwise); VB = 38 kN (↑). I don't know how to get to this result, please show me how to get there step by step
DETERMINE THE INTERNAL FORCE OF MEMBER EF FROM THE FIGURE BELOW. Use four (4) decimal places during computation and two (2) decimal places for the final answer. Note: for compression, include a negative sign ( - ) and for tension, type answer as is.
A vertical steel bar ABC is pin-supported at its upper end and loaded by a force P1 at its lower end. A horizontal beam BDE is pinned to the vertical bar at joint B and supported at point D. Load P2 and moment M are applied at end E. Calculate the vertical displacement δC at point C if the loads are P1 = 2.5 kip, P2 = 1 kip, and M = 25 kip-in. The modulus of elasticity is E = 29,000 ksi and crosssectional areas are A1 = 0.25 in2 A2 =0.15in2 .Ignore the weight of the bar.
Engineering Mechanics DETERMINE THE INTERNAL FORCE OF MEMBER DF FROM THE FIGURE BELOW. Note: for compression, include a negative sign ( - ) and for tension, type answer as is. Use four (4) decimal places during computation and two (2) decimal places for the final answer.
The homogeneous beam AB weighs 400 lb. For each support condition shown in (a) through (d), draw the FBD of the beam and determine the number of unknowns.
The Howe truss is subjected to the loading shown in (Figure 1). Suppose that F = 8.5 kN . Determine the force in member BG and state if the member is in tension or compression.Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension.
calculate the force on Member IH in Kips by method of sections. Express your answer in 2 decimal places. Include (-) negative sign if the force is compression.
From the figure shown, a truss is subjected to loads PI = 15 kN, P2 = 15 kN and P3 = 25 kN at joint C, D and E respectively. Use SI = 3 m; S2 = 4 m Properties of diagonal members (2L75 x 75 x 6): Ag = 1858 mm2 Fy = 248 MPa rx = 22.9 mm ry = 33.2 mm Question: a) What is the axial force in kN, in member DI? b) What is the allowable stress in MPa, in member DI? c) Calculate the allowable load in kN, in member DI.