DateNameIndustry Print Exercise 14-1Refer to the print PR 14-1 and answer the questions below.1. How many columns are featured in the revision history block of this drawing?2. What is the current revision letter assigned to this part?3. What revision specified the surface texture of the tapered portion?4. What are the initials of the person who implemented or approved ECO 68-557?5. Which revision specified the vendor part number of the bushing?6. Revision F changed the maximum axial deflection to .500 at 2000 pounds. What had it been?7. Instead of revision D, E, and F being three letters, what other method of marking could have beenimplemented for these three changes?Review questions based on previous units:8. What is the thread form specified for the internal threaded holes?9. What method was used to show external threads on this part?10. Is this a drawing of multiple parts assembled?11. Does this drawing feature any cutting-plane lines?12. What is the radius of the undercut indicated by a local note?13. What is the maximum material condition diameter of the largest cylindrical feature of this part?14. This drawing has an italic "f" symbol on some surfaces in the left side view. What are these symbols?15. What does the 125 near the check mark at revision A on the tapered surface mean?Inc. Unit 14Drawing Revision Systems29914Print supplied by Clark Equipment CompanyPR 14-1. ASM Silent Block Axle Mounting4.684.622.510.2.4902.5102.4901.0421.0221.0102.3122.2520-1 t.020" B"-12 TAPER PER FOOTGRIND OR MACHINE OPT.AMIN. FLAT.75 BOTH ENDSDDRILL X 45 CHAMFER32HOLE tMUST.28RWTBOTH ENDS.BE 90 t.010 WITH MOUNTINGBOSSESA1252.68+.090005.50(2.18) (1.62) (1.41) 1.0051.2621.2594.264.241722071.09 X 45 CHAMA2.12-0.50 DRILLV.50 FOR ASMOPT. CONST.1-12 UNF-2A, PD.92 .020 THD LENGTH (AMAX. 1.0691MIN. 1.0631"A"A- R MUST BE FREE OF TOOL MARKS-SAE-R630 BHK,Z DOR SAE-R630 BHZ AZ-DENOTESA HIGH MODULUS STOCKE WITH WEATHER RESISTANCE ANDRESISTANCE TO A HYSTERESIS BUILD UPSAE 4140 LEADED C.R.OR STRESSPROOF.62MALLEABLE IRON SAE 32510A DUCTILE 60-45-10 OPT.+.88-1.75-18 UNF-3B, PDV.03 X 30 2 HOLESMAX. .5934MIN. .5889NOTESURFACES "A" & "B" AND "C" & "D" MUSTBE PARALLEL AND IN SAME PLANEDEFLECTION SPEC.:MAX. RADIAL DEFLECTION .050 AT 4000 POUNDSMAX. AXIAL DEFLECTION .500 AT 2000 POUNDSBREAK ALL SHARP CORNERSSIMILAR TO 329676CHG.NO.MICRO UNLESS OTHERWISE SPECIFIED MAX.FILMOR 010 INDUSTRIAL TRUCK DIVISIONCLARK EQUIPMENT CO.CHANGESDATEBYVENDORSDAYTON RUBBER COBUSHINGS INC. NO. 3221 CTOL. ON FIN. DIMSALL OTHER DIMENSIONSDO NOT SCALESCALEMATERIALBATTLE CREEK,MICHIGANNOTEDASM SILENT BLOCK20 JAN HT. TREATMENTWAS .250Z NOTE ADDEDD WAS SAE-R-630-BHKZ 23 DEC JCSCNO. ADDEDWAS 1 MIN. THDA ADDED16 JAN JCSAXLE MOUNTING13 JAN JCSHARDNESS20 THRU 50M. BRESSONDATEDATE 12 APRDATEDATEDRAWN FOR68-55767-97167-65122 MAY DRAWN BY16 OCT CHECKED BY26 JUL RELEASED BY16 MAY MB172207111 OCT MBRN67-393

Question
Asked Nov 6, 2019

I need answers to questions 1, 2, and 3 pertaining to the print provided.

Date
Name
Industry Print Exercise 14-1
Refer to the print PR 14-1 and answer the questions below.
1. How many columns are featured in the revision history block of this drawing?
2. What is the current revision letter assigned to this part?
3. What revision specified the surface texture of the tapered portion?
4. What are the initials of the person who implemented or approved ECO 68-557?
5. Which revision specified the vendor part number of the bushing?
6. Revision F changed the maximum axial deflection to .500 at 2000 pounds. What had it been?
7. Instead of revision D, E, and F being three letters, what other method of marking could have been
implemented for these three changes?
Review questions based on previous units:
8. What is the thread form specified for the internal threaded holes?
9. What method was used to show external threads on this part?
10. Is this a drawing of multiple parts assembled?
11. Does this drawing feature any cutting-plane lines?
12. What is the radius of the undercut indicated by a local note?
13. What is the maximum material condition diameter of the largest cylindrical feature of this part?
14. This drawing has an italic "f" symbol on some surfaces in the left side view. What are these symbols?
15. What does the 125 near the check mark at revision A on the tapered surface mean?
Inc.
help_outline

Image Transcriptionclose

Date Name Industry Print Exercise 14-1 Refer to the print PR 14-1 and answer the questions below. 1. How many columns are featured in the revision history block of this drawing? 2. What is the current revision letter assigned to this part? 3. What revision specified the surface texture of the tapered portion? 4. What are the initials of the person who implemented or approved ECO 68-557? 5. Which revision specified the vendor part number of the bushing? 6. Revision F changed the maximum axial deflection to .500 at 2000 pounds. What had it been? 7. Instead of revision D, E, and F being three letters, what other method of marking could have been implemented for these three changes? Review questions based on previous units: 8. What is the thread form specified for the internal threaded holes? 9. What method was used to show external threads on this part? 10. Is this a drawing of multiple parts assembled? 11. Does this drawing feature any cutting-plane lines? 12. What is the radius of the undercut indicated by a local note? 13. What is the maximum material condition diameter of the largest cylindrical feature of this part? 14. This drawing has an italic "f" symbol on some surfaces in the left side view. What are these symbols? 15. What does the 125 near the check mark at revision A on the tapered surface mean? Inc.

fullscreen
Unit 14
Drawing Revision Systems
299
14
Print supplied by Clark Equipment Company
PR 14-1. ASM Silent Block Axle Mounting
4.68
4.62
2.510.
2.490
2.510
2.490
1.042
1.022
1.010
2.312
2.252
0
-1 t.020
" B"
-12 TAPER PER FOOT
GRIND OR MACHINE OPT.A
MIN. FLAT
.75 BOTH ENDS
DDRILL X 45 CHAMFER
32
HOLE tMUST
.28
RWT
BOTH ENDS.
BE 90 t.010 WITH MOUNTING
BOSSES
A
125
2.68+.09
000
5.50
(2.18) (1.62) (1.41) 1.005
1.262
1.259
4.26
4.24
1722071
.09 X 45 CHAMA
2.12
-0.50 DRILL
V.50 FOR ASM
OPT. CONST.
1-12 UNF-2A, PD
.92 .020 THD LENGTH (A
MAX. 1.0691
MIN. 1.0631
"A"
A
- R MUST BE FREE OF TOOL MARKS
-SAE-R630 BHK,Z D
OR SAE-R630 BHZ A
Z-DENOTESA HIGH MODULUS STOCK
E WITH WEATHER RESISTANCE AND
RESISTANCE TO A HYSTERESIS BUILD UP
SAE 4140 LEADED C.R.
OR STRESSPROOF
.62
MALLEABLE IRON SAE 32510
A DUCTILE 60-45-10 OPT.
+.88
-1.75-
18 UNF-3B, PD
V.03 X 30 2 HOLES
MAX. .5934
MIN. .5889
NOTE
SURFACES "A" & "B" AND "C" & "D" MUST
BE PARALLEL AND IN SAME PLANE
DEFLECTION SPEC.:
MAX. RADIAL DEFLECTION .050 AT 4000 POUNDS
MAX. AXIAL DEFLECTION .500 AT 2000 POUNDS
BREAK ALL SHARP CORNERS
SIMILAR TO 329676
CHG.
NO.
MICRO UNLESS OTHERWISE SPECIFIED MAX.
FILM
OR 010 INDUSTRIAL TRUCK DIVISION
CLARK EQUIPMENT CO.
CHANGES
DATE
BY
VENDORS
DAYTON RUBBER CO
BUSHINGS INC. NO. 3221 C
TOL. ON FIN. DIMS
ALL OTHER DIMENSIONS
DO NOT SCALE
SCALE
MATERIAL
BATTLE CREEK,
MICHIGAN
NOTED
ASM SILENT BLOCK
20 JAN HT. TREATMENT
WAS .250
Z NOTE ADDED
D WAS SAE-R-630-BHKZ 23 DEC JCS
CNO. ADDED
WAS 1 MIN. THD
A ADDED
16 JAN JCS
AXLE MOUNTING
13 JAN JCS
HARDNESS
20 THRU 50
M. BRESSON
DATE
DATE 12 APR
DATE
DATE
DRAWN FOR
68-557
67-971
67-651
22 MAY DRAWN BY
16 OCT CHECKED BY
26 JUL RELEASED BY
16 MAY MB
1722071
11 OCT MB
RN67-393
help_outline

Image Transcriptionclose

Unit 14 Drawing Revision Systems 299 14 Print supplied by Clark Equipment Company PR 14-1. ASM Silent Block Axle Mounting 4.68 4.62 2.510. 2.490 2.510 2.490 1.042 1.022 1.010 2.312 2.252 0 -1 t.020 " B" -12 TAPER PER FOOT GRIND OR MACHINE OPT.A MIN. FLAT .75 BOTH ENDS DDRILL X 45 CHAMFER 32 HOLE tMUST .28 RWT BOTH ENDS. BE 90 t.010 WITH MOUNTING BOSSES A 125 2.68+.09 000 5.50 (2.18) (1.62) (1.41) 1.005 1.262 1.259 4.26 4.24 1722071 .09 X 45 CHAMA 2.12 -0.50 DRILL V.50 FOR ASM OPT. CONST. 1-12 UNF-2A, PD .92 .020 THD LENGTH (A MAX. 1.0691 MIN. 1.0631 "A" A - R MUST BE FREE OF TOOL MARKS -SAE-R630 BHK,Z D OR SAE-R630 BHZ A Z-DENOTESA HIGH MODULUS STOCK E WITH WEATHER RESISTANCE AND RESISTANCE TO A HYSTERESIS BUILD UP SAE 4140 LEADED C.R. OR STRESSPROOF .62 MALLEABLE IRON SAE 32510 A DUCTILE 60-45-10 OPT. +.88 -1.75- 18 UNF-3B, PD V.03 X 30 2 HOLES MAX. .5934 MIN. .5889 NOTE SURFACES "A" & "B" AND "C" & "D" MUST BE PARALLEL AND IN SAME PLANE DEFLECTION SPEC.: MAX. RADIAL DEFLECTION .050 AT 4000 POUNDS MAX. AXIAL DEFLECTION .500 AT 2000 POUNDS BREAK ALL SHARP CORNERS SIMILAR TO 329676 CHG. NO. MICRO UNLESS OTHERWISE SPECIFIED MAX. FILM OR 010 INDUSTRIAL TRUCK DIVISION CLARK EQUIPMENT CO. CHANGES DATE BY VENDORS DAYTON RUBBER CO BUSHINGS INC. NO. 3221 C TOL. ON FIN. DIMS ALL OTHER DIMENSIONS DO NOT SCALE SCALE MATERIAL BATTLE CREEK, MICHIGAN NOTED ASM SILENT BLOCK 20 JAN HT. TREATMENT WAS .250 Z NOTE ADDED D WAS SAE-R-630-BHKZ 23 DEC JCS CNO. ADDED WAS 1 MIN. THD A ADDED 16 JAN JCS AXLE MOUNTING 13 JAN JCS HARDNESS 20 THRU 50 M. BRESSON DATE DATE 12 APR DATE DATE DRAWN FOR 68-557 67-971 67-651 22 MAY DRAWN BY 16 OCT CHECKED BY 26 JUL RELEASED BY 16 MAY MB 1722071 11 OCT MB RN67-393

fullscreen
check_circleExpert Solution
Step 1

There are 6 columns which are featured in the revision history block of this drawing. And that column are A, B, C, D, E and F.

DATE
BY
CHANGES
16 JAN JCS
13 JAN JCS
WAS .250
E
Z NOTE ADDED
WAS SAE-R-630-BHKZ 23 DEC JCS
NO. ADDED
16 MAY MB
11 OCT MB
19 JUL MB
C
В
WAS 1 MIN. THD
ADDED
A
help_outline

Image Transcriptionclose

DATE BY CHANGES 16 JAN JCS 13 JAN JCS WAS .250 E Z NOTE ADDED WAS SAE-R-630-BHKZ 23 DEC JCS NO. ADDED 16 MAY MB 11 OCT MB 19 JUL MB C В WAS 1 MIN. THD ADDED A

fullscreen
Step 2

The first revision was done in 19 JUL which was revised by letter A. The second revision was done in 11 OCT whi...

CHANGES
DATE
F WAS .250
E Z NOTE ADDED
16 JAN
13 JAN
D WAS SAE-R-630-BHKZ 23 DEC
CI NO. ADDED
WAS
A ADDED
16 MAY
11 OCT
1 MIN. THD
19 JUL
help_outline

Image Transcriptionclose

CHANGES DATE F WAS .250 E Z NOTE ADDED 16 JAN 13 JAN D WAS SAE-R-630-BHKZ 23 DEC CI NO. ADDED WAS A ADDED 16 MAY 11 OCT 1 MIN. THD 19 JUL

fullscreen

Want to see the full answer?

See Solution

Check out a sample Q&A here.

Want to see this answer and more?

Solutions are written by subject experts who are available 24/7. Questions are typically answered within 1 hour*

See Solution
*Response times may vary by subject and question
Tagged in

Engineering

Mechanical Engineering

Other

Related Mechanical Engineering Q&A

Find answers to questions asked by student like you

Show more Q&A add
question_answer

Q: A circular balloon is being filled through the inlet, which has a cross-sectional area denoted as A1...

A: Write the expression for the volume of the balloon (V) and consider it as equation (1). Next, write ...

question_answer

Q: -1. Natural Convection from an Oven Wall. The oven wall in Example 15.5-1 is insu- lated so that the...

A: Given:As given in the question that the wall is insulated, so surface temperature of wall is 366.5 L...

question_answer

Q: I need answers to questions 1, 2, and 3 pertaining to the print provided. Note: A tutor keeps puttin...

A: If any changes in the part feature are made, the changes are recorded in the specified format in the...

question_answer

Q: A tensile test specimen has a gage length = 3.0 in and diameter 0.75 in. Yielding occurs at a load o...

A: Given data as per question

question_answer

Q: The attached figure shows a gas contained in a vertical piston– cylinder assembly, where D = 10 cm. ...

A: a)Calculate the change in elevation of the piston-shaft.

question_answer

Q: Question 1 A simply supported composite beam 3 m long carnes a uniformly distrbuted load of intensit...

A: Calculate the maximum bending moment. 

question_answer

Q: 3.23 3.24 d 3.25. Gas at constant T and P is contained in a supply line connected through a valve to...

A: We’ll answer the first three subparts of the question since the exact one wasn’t specified. Please s...

question_answer

Q: Two masses are coupled by a pulley and restrained by a spring. The spring has an unstretched length ...

A: Given data,

question_answer

Q: Air expands through a turbine operating at steady state. At the inlet, p1 = 150 lbf/in.2, T1 = 1400°...

A: Given:At state 1