Define Mohr’s circle?

Q: What about Mohr's circle?

A: In the previous question, Given: The diameter of shaft, d = 20 mm = 0.02 m The maximum bending…

Q: choose correct option nd do exolain plz

A: Given that, Elevation of the tank, H=37 ft,k of the entrance=0.5,Diameter of the pipe, D=12 in=1…

Q: With the help of a neat free-hand sketch, explain how to construct the involute of a circle.

A: construct the involve of a circle.

Q: What is the mean roundness of a fruit with 2.0cm, 5.0cm, 3.5cm, 7.0cm, 1.6cm and 3.2cm radii of…

A: Mean roundness= 0.49556

Q: Which et h

A: introduction: Forging is a manufacturing technique that involves pounding, pressing, or rolling…

Q: Draw an archemedian spiral of 1½ convulations with the greatest radius of 100mm and the smallest…

A: It is the locus corresponding to the locations over time of a point moving away from a fixed point…

Q: What are the 2 things that need to be calculated to draw Mohrs Circle?

A: The two things that are needed to be calculated to draw mohrs circle are: 1.Normal stress. 2.Shear…

Q: A wire of length 50 is to be cut into two pieces, one peing bent to form a square and the other to…

A: Given:Length of wire,L=50m(unit taken as metere as not specified)Now .Let the length of square…

Q: Identify (circle) which of the following

A: Incomplete Question nothing is there.   Can U resend the full question instead of this one.

Q: Mohr's circle for an element is shown below, each grid square is 20 MPa. The principal plane is: I…

A:

Q: Why is it called Mohr's circle?

A: Mohr’s  circle is graphical representation which enables us to visualize the relationships between…

Q: per of degrees of free nanism shown below is

A: introduction:here we have to find out dof

Q: 2 x (2 + 2) = 8, 3 x (3 + 2) = 15, 4 x (4 + 2) = 24, 5 x (5 + 2) = 35, the 7th line in the pattern…

A: Given Data⇒ 2 x (2 + 2) = 8, 3 x (3 + 2) = 15, 4 x (4 + 2) = 24, 5 x (5 + 2) = 35

Q: What does view one represent in this flange?

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: - length and the tio of the cross-se 10 am).

A: let the resistance of the wires is R length of wires is L resistivity of Copper , pc = 1.68 *10^-8…

Q: what is the Moment at point A

A: First find the moment produce by given torque as follows.

Q: According to the following figure, calculate the horizontal and vertical force on a circular segment…

A: Given: The radius of the segment, r = 2 m The width of segment, b = 5 m

Q: A hammer is balanced at the point "A", close to the metal part. If this hammer is then cut along the…

A: Consider the diagram shown below for the hammer with the center of masses for each side.

Q: What are the Regions of Concentrated Force and Moment?

A: Concentrated moments which have fixed value, Whereas Moment due to eccentric loads vary with…

Q: ged parabolic arc the max, bendin

A:

Q: What is the angle of reference for Mohrs Circle?

A: The Mohr circle is a diagrammatic representation of normal stress and shear stresses acting on the…

Q: answer 12

A: The sum of the length of the shortest and the longest of a planar quadrilateral linkage if less than…

Q: What is the moment-area method?

A: The moment-area method is one of the methods for determining the slope and deflection generated in a…

Q: What is the procedure of using the Mohr's circle?

A: The procedure of Mohr's Circle is given as, (1) Draw the vertical and horizontal coordinates. The…

Q: Draw the [1 1 0] and [10 1] directions on a cubic unit cel.

A:

Q: what is the diameter of this inner circle?

A: Solution:

Q: The X coordinate of an Isosceles triangle of base b and height h is?

A: In an isosceles triangle the x coordinate is always the one third to its height and the y coordinate…

Q: . Circle the correct section view out of the three possibilities. Would a half section been…

A: The section 2 is correct. The reason is mentioned below. First look at the cutting plane, it is…

Q: N =24 5- To calculate number of grains used

A:

Q: If you have a half circle made of steel and the other half of wood, is the center of the circle…

A:

Q: N*=24 5- To calculate number of grains used

A: Given: Grains are small size crystal that combines and formed a solid material.

Q: (ii) the orientations of the major and minor principal planes relative to the left vertical side of…

A:

Q: A hollow steel has an outside diameter of 5in. and it's inside diameter is 4in. What is the…

A: Outside diameter, do=5 inInside diameter, di=4 in

Q: A/ Draw (F.B.D) for the rod (200N) shown in Fig. (1-a).

A: F.B.D. consist all external force and reaction apllied on Rigid body. For solution refer below…

Q: What is a bending moment?

A: Bending moment: Bending moment is a moment which developed in any structure or body when a force or…

Q: This composite shape is composed of a square, a half-circle, a triangle and a circular hole.…

A:

Q: what is the angle in red?

A: Given Figure to find the angle marked in red color

Q: Activity 1. For the H - section shown, Find the value of h so that Ix = Iy. %3D 20mm 100mm |20mm…

A:

Q: How can I draw in mohr's circle?

A: Solution:

Q: In step 4, it should be the A and not the y right? So it should be FBD divided by 4.04 which is the…

A:

Q: What does the each point on Mohr’s circle represent?

A:

Q: This is a Flange. What does The number 3 Represent

A:

Q: Explain Why we use Mohtrs Circle, and What it is used for?

A: By the help of the Mohr circle, we calculate principle stress, maximum shear stress, and stresses on…

Q: sof mohr circle

A:

Q: minimum permissible basic circle radius.

A: Given; A cam with a translating flat-face follower is desired to have the follower motion:…

Q: This composite shape is composed of a square, a half-circle, a triangle and a circular hole.…

A: Find the moment of inertia of half circle about x axis.

Q: What is thé perimeter of the triangle? mm FRP | PRP

A: Here we have to find the perimeter of triangle FRP and PRB are the Geometric views FRP= Frontal…

Q: What steps are required to draw and use Mohr’s circle?

A: Given Data⇒Mohr circleProblem definition⇒What steps are required to draw and use Mohr’s circle?

Q: Which of the ff are methods to adjust the gaps in centerlines ¢er marks? A. Center B. Center2 C.…

A: Different types of lines used in AutoCAD are: Continues line Center Line Hidden Line

Q: e radius of the curve?

A: To determine Radius of curve