I need the answer as soon as possible Determine the maximum, minimum and average pressure in a plate clutch when thaxial force is 4kN. The inside radius of the contact surface is 50 mm and the outsidkradius is 100 mm. Assume uniform wear.

Answered: Image /qna-images/answer/fcb4ad38-ab00-497e-a94d-e9c798ec45b9.jpg

Determine the maximum, minimum and average pressure in a plate clutch when the axial force is 4kN. The inside radius of the contact surface is 50 mm and the outsid radius is 100 mm. Assume uniform wear.

Determine the maximum, minimum and average pressure in a plate clutch when the axial force is 4kN. The inside radius of the contact surface is 50 mm and the outsid radius is 100 mm. Assume uniform wear.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A steel shaft of 2.5 inch diameter rotates at 500 rev/min and transmits 120 hp through a gear.…

Q: An automobile single-plate clutch consists of a pair of contacting surfaces. The inner and outer…

Q: A flat belt drive used to transmit power from a motor running at 1600 m/min to a machine. The belt…

Q: A cone clutch is mounted on a shaft which transmits power at 200 rpm. The small diameter of the cone…

Q: 3.A multiple disc clutch has three discs on the driving shaft and two on the driven shaft, providing…

A: Answer: The maximum axial intensity of pressure between the discs: 0.12665 MPa.

Q: A plate clutch consists of one pair of contacting surfaces. The inner and outer diameters of the…

A: Given data di = 100 mm , ri = 50 mmd0 = 200 mm , r0 = 100 mmCoefficient of friction…

Q: (b) An automotive clutch driven plate is clamped between a fly- wheel and a sprung pressure plate.…

A: Friction Clutches : Friction clutches are mechanical devices which are used to transmit power from…

Q: Design a toggle jack to lift a load of 5 kN. The jack is to be so designed that the distance between…

A: Hi, I have worked very hard to provide you with this solution, please UPVOTE this answer, thanks!!…

Q: multi-disc clutch has three discs on the driving shaft and two on the driven shaft. The inner…

A: Given data: The number of driven plate is n1=2 The number of driving plate is n2=3 The inner…

Q: A multiplate friction clutch is required to transmit 72 kW at 3600 r.p.m. The plates are alternately…

A: Given data: - The power transmitted by the clutch is P = 72 kW. The speed of the clutch is N =…

Q: Consider a flat plate clutch with maximum pressure of 50 KPa, outside diameter of 30 cm and inside…

A: "Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: A cone clutch has an angle of 12 dgrees and coefficient of friction of 0.42. Find the axial force…

Q: A multi-disk clutch consists of two steel disks with one bronze disk. The inner and outer diameters…

A: Given data:

Q: Q1/ A plate clutch having a single driving plate with contact surfaces on each side is required to…

Q: Given: In a ring compression test, a specimen is 15mm in height with outside diameter of 35mm and…

A: Given Height= 15mm Outside Diameter= 35mm Inside Diameter= 10mm The Thickness is reduced by 50%…

Q: A multiplate clutch has three pairs of contact surfaces. The outer and inner radii of the contact…

A: Given:Number of pairs=3Speed,N=1500rpmOuter radius,r1=100mm=0.1mInner…

Q: An automobile single plate ciutch consists of a pair of contacting surtaces. The inneOr and outer…

Q: Q1/ A plate clutch having a single driving plate with contact surfaces on each side is required to…

Q: 3/ A multi plate clutches an included angle of 180º. A multi plate clutch, has 2 disc: on the…

A: Given:Total disc on driving shaft=2Disc on driven shaft=1Outer diameter=1000 mmOuter radius, r1=500…

Q: b) An automotive clutch driven plate is clamped between a fly- wheel and a sprung pressure plate.…

A: A clutch is a device that allows two parts with a shared axis of rotation to connect and disengage…

Q: A single disc clutch is used to transmit 12kW power at 1000rpm. The axial pressure is limited to…

Q: Design a compression coupling for a shaft to transmit 1300 N-m. The allowable shear stress for the…

Q: An engine running at 1100 rpm drives a line shaft by means of a belt. The engine pulley has a 9 in.…

A: Belt drives are a sort of frictional drive that transmits power from one shaft to the next. a system…

Q: A pulley is keyed to a 56.8mm diameter shaft by a 7/16 in x 3 in flat key. The shaft rotates at 697…

A: D = 56.8mm = 2.236 in h = 7/16 in L = 3 in N = 697 rpm τK= 66 ksiτh= 59 ksiτs= 72 ksi

Q: Question 01: Draw and label any screw thread and a fastener separately. Also, discuss the types of…

A: As per the Question Demand of Draw and label any Screw thread and fastener . SO, screw thread-Square…

Q: The nominal diameter of a triple- threaded square screw is 50 mm, while the pitch is 8 mm. It is…

A: (i) To find : The torque required to raise the load. Given : The nominal diameter of screw is d=50…

Q: An oil immersed multi-disk clutch, with moulded asbestos on one side and steel disks on the other,…

A: Given data as per question Torque transmitted by clutch =75Nm coefficient of friction =0.1…

Q: A single plate friction clutch with both sides of plate being effective is used to transmit power at…

Q: ) Consider a flat plate clutch with maximum pressure of 50 KPa, outside diameter of 30 cm and inside…

Q: Design a compression coupling for a shaft to transmit 1300 N-m. The allowable shear stress for the…

Q: A flange coupling is to connect two 57mm shafts. The hubs of the coupling are each 111m in diameter…

Q: Q4. Two plates have a length (L) and thickness (t), were welded together. Assume these plates have…

A: Q4: Weld joint: A weld joint is a joint which is used to join two or more plates by adding a fusion…

Q: 4. A multiple disc clutch running in oil is required for a touring motorcycle. The power demand is…

A: Given: P=75 kWN=9000 rpmd0=200 mm

Q: In a bolted joint two smooth members are connected with an axial tightening force of 2200 N. If the…

Q: The standard cross-section for a flat key, which is fitted on a 50 mm diameter shaft, is 16 x 10 mm.…

A: Given, Diameter of shaft = d = 50 mmWidth of key = b = 16 mmHeight of key = h = 10 mmYield Strength…

Q: A pulley is keyed to a 2.5 in diameter by means of a 5/8’’ x 7/16’’ x 3’’ flat key. The allowable…

Q: Describe the failure of a hollow torque tube. Calculate the forces creating the failure

A: It is asked to describe the failure in the hollow torque tube

Q: A clamp coupling is to transmit a power of 13 kW to a shaft rotating at a speed of 511 rpm.…

Q: A motor is to transmit 150 kW to a piece of mechanical equipment. The power is transmitted through a…

Q: The axial pressure on a single disc clutch (both sides of the disc is effective) is limited to 0.12…

Q: A single plate clutch is required to transmit 150 kW at 6000 r.p.m. The clutch facings available…

A: The answer is given below

Q: 1. A multiple friction clutch is required to transmit 89.52 kW at 3000 rpm. The plates are…

A: Given data as per question Power to be transmitted = 89.52 kw Speed = 3000 rpm coefficient of…

Q: Q3/ A multi plate clutches an included angle of 120°. A multi plate clutch, has 2 discs on the…

A: Given:Disc in driving shaft=2Disc in driven shaft=1Outer diameter=100 cm or 1000 mmouter radius,…

Q: A 8 mm thick leather open belt connects two flat pulleys. The smaller pulley is 300 mm diameter and…

Q: Determine the maximum, minimum and average pressure in a plate clutch when the axial force is 4kN.…

Q: Design a compression coupling for a shaft to transmit 1300 N-m. The allowable shear stress for the…

Q: Q1/ A plate chutch having a single driving plate with contact surfaces on each side is required to…

Q: An multi axial plate clutch used in injection molding machine consist of a three pairs of contact…

Q: ...A plate clutch with single driving plate with contact surfaces on each is required to transmit 35…

A: Answer: The inside radius of the frictional surface: 110.7582 mm

Question

I need the answer as soon as possible

Determine the maximum, minimum and average pressure in a plate clutch when th
axial force is 4kN. The inside radius of the contact surface is 50 mm and the outsidk
radius is 100 mm. Assume uniform wear.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

the power transmitted by a single plate clutch at a speed of 2000 rpm, if the outer and inner radii of Triction surfaces -are 150 mm and 100 mm respectively. The maximum intensity of pressure at any point of contact surface should-not exceed 0.8 x 105 N/m2. Take both sides of the plate as effective and coefficient of friction = 0.3. Assume uniCalculateform wear.
...A plate clutch with single driving plate with contact surfaces on each is required to transmit 35 kW at 2400 rpm. Given that μ = 0.29, R = 1.25r, Pmax = 0.2 MPa, determine the inside radius of the frictional surface in mm. Assume the uniform wear conditions.
The axial pressure on a single disc clutch (both sides of the disc is effective) is limited to 0.12 Mpa. This is designed for a vehicle with 13kW power at a speed of 700 rpm. Assume uniform wear conditions and a friction coefficient of 0.25. If the outer dimater of the disc is 1.25 times the internal diameter, determine the dimensions of the disc lining and the axial force exerted by the springs.
An automotive plate clutch consists of two pairs of contacting surfaces with asbestos friction lining. The maximum engine torque is 200 N-m. The coefficient of friction is 0.35. The inner and outer diameters of friction lining are 200 and 300 mm respectively. Clamping force is provided by nine springs, each compressed by 4 mm to give a force of 700 N, when the clutch is new.(i) What is the factor of safety with respect to slippage when the clutch is brand new?(ii) What is the factor of safety with respect to slippage after initial wear has occurred?(iii) How much wear of friction lining can take place before the clutch will slip?
A cone clutch is mounted on a shaft which transmits power at 200 rpm. The small diameter of the cone is 200 mm, the cone face is 50 mm and the cone face makes an angle of 12 degrees with the horizontal. Determine the axial force necessary to engage the clutch to transmit 7 kW if the coefficient of friction of the contact surfaces is 0.15. What is the maximum pressure on the contact surfaces assuming uniform wear?
The external and internal diameter of a single plate clutch are 125 mm and 100 mm, respectively. It is used to transmit power at limited (maximum) axial pressure of 0.2 MPa. Which of the following is the axial force exerted by the springs? Assume uniform wear conditions. Choices: 790N1960N 440N 980N
Determine the size of the clutch plate suitable for an Ambassador car employing asingle plate type friction clutch and developing 37.5 kW at 4282 rpm. The insidediameter of the clutch plate is 0.6 times its outside diameter and it is to be ensured thateven after a loss of 30% of the engine torque due to wear of the clutch facing, the clutchdoesn’t slip. The intensity of the pressure on the facing is not to exceed 70 kPa. Assumeµ = 0.3.
A multiplate clutch has three pairs of contact surfaces. The outer and inner radii of the contact surfaces are 100 mm and 50 mm respectively. The maximum axial spring force is limited to 1 kN. If the coefficient of friction is 0.35 and assuming uniform wear, find the power transmitted by the clutch at 1500 r.p.m.
An multi axial plate clutch used in injection molding machine consist of a three pairs of contact surfaces for engaging and disengaging power from the engine. The engine used for power has a maximum torque capacity of 120 N-m and is transmitted to machine without losses. The permissible intensity of pressure is 350 kPa and the coefficient of friction is 0.35 for the clutch system used in the machine. It was determined that the machine will operate on maximum capacity of torque if the ratio of inner diameter to outside diameter of the axial clutch is 0.577. Assuming uniform wear theory, calculate the inner and outer diameters of the friction lining.
A multiple friction clutch is required to transmit 89.52 kW at 3000 rpm. The plates are alternatively of steel and phosphor bronze and they run in oil. The coefficient of friction is 0.08. The internal radius of the friction surface is 0.8 times the radius of the external surface. The axial pressure is limited to 20 x 104 N/m2. If the maximum diameter of the frictional surface is not to exceed 250 mm, determine the number of plates required.
The factor of safety against slipping in the friction clutch = 1.3; coefficient of friction=0.3; working speed= 600 rpm; friction surface number= 2; If required clamping force = 2917 N, clutch outer diameter = 400 mm, clutch inner diameter = 160 mm, what is the transmitted power?
A local utility vehicle production company have considered using in one of its design a multi-disc clutch consisting of a 9 steel disc and 8-bronze discs with effective outside and inside diameter of 220mm and 160mm, respectively. If the shaft turns at 150rpm and an axial force of 600N is applied, find the horsepower capacity, considering a coefficient of friction of 0.25