Determine the shear and moment equations and the draw the shear and moment diagrams for the beam. 1.5 kN/m

Q: 1. GIVEN: NACA 2421 AND chord is 115 cm Determine:  a) Maximum Camber  b.) Position of Max.…

A: a) Maximum Camber  b.) Position of Max. Camber,  c.) thickness

Q: The framework of an under construction balcony is subjected to a distributed wind load of 600 N/m as…

A:

Q: The free-rolling ramp has a mass of 40 kg. A 10-kg crate is released from rest at A and slides down…

A: The mass of the crate is m=10 kg The mass of ramp is M=40 kg The system is at rest at point A.

Q: Q4/ Determine the parameters for an equivalent system model of the system of Figure (E) when , the…

A:

Q: 4s+1 3- Nise (4.4) A unity feedback control system has the following open-loop transfer function:…

A: The expression for the time response. Given: The open loop transfer function is G(s)=4s+14s2.

Q: allowable force for the rivet joint shown in the figure, if the allowable shear stress is MPa 110,…

A:

Q: For the beam and loading shown, a. Compute the support reactions with the help of a free-body…

A:

Q: determine the magnitude of the reactions at A and B that act normal to the gate.

A: Width of the Gate = 0.2 m Density of the seawater  ρ = 1019 Kg/m3 Depth of the water hA = 2.6 m The…

Q: A door in the side of a tank is 20cm wide and 30cm high. If the tank is filled with oil r.d. 0.82 to…

A:

Q: Q4.10) Figure 4.10 shows a flow-obstruction flowmeter with circular cross sections. The fluid is…

A: Note: As per the policy, we can solve the first three subparts. Please resubmit the remaining part.…

Q: The man in the figure below is pulling a drum over a circular hill. All surfaces are smooth (no…

A: W=60 N   To find: The tension ,T on the rope for the drum

Q: ꜱᴛᴇᴀᴍ ᴇɴᴛᴇʀꜱ ᴛʜᴇ ᴛᴜʀʙɪɴᴇ ᴀᴛ 2.2 ᴍᴘᴀ ᴀɴᴅ 250°ᴄ. ꜰᴇᴇᴅᴡᴀᴛᴇʀ ᴇɴᴛᴇʀꜱ ᴛʜᴇ ꜱᴛᴇᴀᴍ ɢᴇɴᴇʀᴀᴛɪɴɢ ᴜɴɪᴛ ᴀꜱ…

A: Steam enter turbine at 2.2MPa and 250'C Saturated liquid 30'C

Q: A steam power plants operates between a boiler pressure of 40 bar and a condenser pressure of 0.04…

A:

Q: Q3/ Consider a point in a structural member that is subjected to plane stress. Normal and shear…

A:

Q: @ | 1/3 3-੧x d

A: The integral. Given: The integral is ∫01/331-9x2 dx.

Q: The framework of an under construction balcony is subjected to a distributed wind load of 600 N/m as…

A:

Q: Q2/ If the turbine extracts 400 kW from the flow, what flowrate must be passing through the system?…

A:

Q: 4. If the bearing pads at A and B support only vertical forces, determine the greatest magnitude of…

A: The bending stress allowable is σallo=15 MPa The shear stress allowable is τallow=1.5 MPa

Q: Q1/A) A thermometer having a time constant of (90sec) is initially at (300°F), it is suddenly placed…

A: The thermal time constant of the thermometer→τ=90 sec Initial temperature of the…

Q: ꜱᴛᴇᴀᴍ ᴇɴᴛᴇʀꜱ ᴛʜᴇ ᴛᴜʀʙɪɴᴇ ᴡɪᴛʜ ᴀɴ ᴇɴᴛʜᴀʟᴘʏ ᴏꜰ 2923.3 ᴋᴊ/ᴋɢ. ꜰᴇᴇᴅᴡᴀᴛᴇʀ ʟᴇᴀᴠᴇꜱ ᴀꜱ ꜱᴀᴛᴜʀᴀᴛᴇᴅ ʟɪQᴜɪᴅ ᴀᴛ ᴀ…

A:

Q: Q1/A) A thermometer having a time constant of (90sec) is initially at (300°F), it is suddenly placed…

A:

Q: Water flows from a large tank into a 6" diameter pipe through an entrance condition of a square…

A: Given:Pipe diameter, D2=6 inchRadius of the rounded inlet, r=0.12 inchFind:The head loss reduced at…

Q: An incompressible fluid (density 1000kg/m3) is flowing through a pipe with a constriction. The pipe…

A:

Q: 1.+Liquid-liquid extraction of acetic acid from water by isopropyl ether. Isopropyl ether (E) is…

A: a)  As per the given data, the feed and the solvent is represented by point F1 and S respectively.…

Q: When employing solid modelling, a designer may make an item by sculpting and moulding it rather than…

A: To explain

Q: Consider the simple diffusion equation with a source term: ft-Dfxx = kf Use the central-space,…

A: In order apply the central-space, forward-time difference method, we approximate the derivatives as…

Q: Hello, could I get some help with a Differential Equations problem that involves Eigenvalues and…

A:

Q: An amount of gas inside an insulated vessel contained 45000J of internal energy. The gas expands…

A:

Q: The turnbuckle is tightened until the tension in the cable AB equals 2.9 kN. Determine the vector…

A:

Q: QUESTION 2 The shaft carries four masses A, B C and D respectively. Magnitude of masses A and D…

A: To Find- The magnitude and position of the masses B and C relative to the masses A in order to…

Q: Find the Freudeinstein for the four rod mechanism in the figure. 02 a R2₂ 0₂ 03 Equation to find the…

A: The vector loop closure equation can be written as : R2+R3-R4-R1=0  ...... (1) Now writing the…

Q: A 140 m long pipeline runs between two reservoirs, both ends being under water, and the intake end…

A: Given:Length of the pipe, L=140 mDifference between the water levels in the two reservoirs, H=40 ma…

Q: the pressure and temperature at the end of the heat-addition process, (b) the net work output, (c)…

A: From the temperature, the relative specific volume and internal energy at inlet conditions can be…

Q: Thin wire bent into a three-sided "u" shape in the form of a block with pieces of equal length "b"…

A:

Q: A shell-and-tube heat exchanger must heat 2.8 kg/s of a solution with a specific heat of 3.25…

A: Mass flow rate of the solution→m=2.8 Kg/s Specific heat of the solution→Cp=3.25 KJ/KgK Initial…

Q: The base of a damped spring-mass system, with m=25 kg and k = 2500 N/m, is subjected to a harmonic…

A:

Q: Looking for correct handwritten solution. 1)An industrial water shutoff valve is designed to operate…

A: Given Effort Force =Fe= 10 N Resistance Force =Fr = 30 NDiameter of axle =Da=.35 m To Find Diameter…

Q: If El= 2x10¹0 N.cm² and if each element of the beam is 300 cm long: a. Construct one-dimensional…

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: An ideal refrigeration cycle is used as an air conditioning system. The interior of the room must be…

A:

Q: Replace the axle shaft with the rotating shaft, show your idea through the neat sketch only. 3 10

A: The axle shaft is used to provide the wheel support and it can not rotate or transmits the power…

Q: Design a six-horsepower engine for a snowblower. Decide on the operating speed, number of strokes in…

A:

Q: 4. A student followed strictly correct procedure in the lab during the experiment of moment of…

A:

Q: 1. Determine the value of A, B and C in the bending moment diagram. [A=1148, B=1188, C=-432] V (N)…

A:

Q: 2. [Relative Motion Analysis using Rotating Axes] At the instant shown the truck is moving toward…

A: The speed of the truck is vtruck=1.5i⇀ m/s. The acceleration of the truck is atruck =0.5i⇀ m/s2 The…

Q: 5. Calculate the brake thermal efficiency of a supercharged 4-cylinder, four stroke with a bore and…

A: Given data Dynamometer reading =143.3 lbArm length = 13.8" = 1.15 ftSpeed = 440 rpmTime of test = 14…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: Load at fixed point of beam F1=1200N/m Length of beam = 6m Load at free end of beam =1600N/m To find…

Q: A trailer has 1000 kg mass when it is fully loaded and 250 kg when it is empty. The spring stiffness…

A: given

Q: Heat is transferred to a heat engine from a fumace at a rate of 120KW. If the rate of waste heat…

A:

Q: If the composite wall in the figure has a width of 120 cm, determine the heat flux in [kW],…

A:

Q: Water is pumped from a lake to a storage tank 30 m above at a rate of 75 L/s while consuming 21.8 kW…

A: Given:Elevation difference between the lake and storage tank, ∆z=30 mWater flow rate, Q=75…

Bending Moment

In general, we can define the bending moment as the reaction induced when a certain amount of load or force is applied to an element which makes it bend.