Differentiate between Assembly Drawing and Assembly Chart?

Q: In this project, you have been asked to select the best joining and assembly process for a product…

A: Answer-1: It is always important to have the minimum number of parts and lightweight in an assembly…

Q: Describe the different manufacturing processes for Aircraft wing production

A: First of all I would like to tell you that material used in manufacturing of wings in aircraft…

Q: a) hourly production rate of the plant, (b) number of workers and workstations required

A: Given: Annual capacity=240000 plant will operate 50 wk/yr, 2 shifts/day, 5 days/wk, and 8.0 hr/shift…

Q: What is the working principle of shaper machine?

A: Shaper machine is type of machine tool which is used for material removal process by relative motion…

Q: I need answers to this part for a review activity.

A: Contour definition is used to describe the profiles of complicated shapes, whereas tube bending is a…

Q: product load

A: c. 0.74kW

Q: Solve problem 17.5 but assume that defects never jam the workstations.  Other data are the same…

A: Given data,

Q: Course: Computer Aided Manufacturing How to assign codes to any five parts with different…

A: In parts classification and coding, similarities among parts are identified, and these similarities…

Q: How to construct an assembly process chart for bolt and washer assembly.

A: Given :-  How to construct an assembly process chart for bolt and washer assembly.

Q: Why Cross-rail attachment is required in shaper?

A: Cross rail attachment is required beacuse

Q: Drawing is an example of __________________________________ primary shaping process surface…

A: Solution:

Q: During the operation of the product, does the part move relative to all other parts already…

A: "Design for Manufacture and Assembly(DFMA)"  optimises the manufacturing and assembly operations of…

Q: In which of the following layout type, materials are fed into the first machine and finished…

A: givenMaterials are fed into the first machine and finished products come out of the last machine.

Q: Course: Computer Aided Manufacturing How to explain about part classification and coding system?

A: Objective: To explain the part classification and coding system.

Q: 150* 6. The component above requires equally spaced slots 2-1/2" apart over a 150" span. How many…

A:

Q: Discuss what would likely happen if a needed sscrew or a working tool is missing from a traditional…

A: Given Mass production line To find Discussion about screw requirement

Q: A

A: ghghh

Q: Need to sketch initial design of automated hammering machine. Sketch should be in simple and proper…

A: Automated hammering machine can be used for forging operation and can be power driven combined with…

Q: Create a flowchart or process diagram for making a particleboard from sugarcane bagasse utilizing a…

A:

Q: of the assembly lin

A:

Q: In which of the following layout type raw materials are fed into the first machine and finished…

A: The layout is defined as the systematic arrangement of the machines, equipment, and other entities…

Q: the shaper machine work processes

A:

Q: Expound why we use CAD and its advantage to manual drawing.

A: Given CAD To find Advantage of CAD use Advantage of CAD over manual drawing

Q: Machine Design

A: Ry = 183.1 lbfRz = -861.5 lbf Speed =1200 rev/min Life-time = 15 kh = 15000 h Reliability, RD = 95%…

Q: Which one of the part definitions is right? O A part is an unit which is involved in the final…

A: Solution:

Q: With reference to the drawing callout in Figure 4 below, which part(s) would 'pass' or 'fail'…

A:

Q: The .. view is best suited for assembly drawings where both internal and external construction are…

A: The internal parts of the object are shown by the sectional views. There are various types of…

Q: Buffing is an example of _______________________________________ process. secondary machining…

A: It is required to fill the blank

Q: The first element in a feature control frame in Solidworks denotes what?

A: The products may vary slightly in terms of dimensions as compared to the initial designs because of…

Q: Describe three basic categories of material removal process.

A: given: Describe three basic categories of material removal process.

Q: What are the step-by-step procedures on the shaper machine work processes? On clean paper and…

A: Shaper Machine :- The shaper machine is a reciprocating type of machine basically used for…

Q: a) Define what is meant by "selective assembly" and briefly explain why it is used and give one…

A: (a) Selective assembly  Process capability = 4 ( desired tolerance )     For example 0.4  = 4 * 0.1…

Q: a) What is the difference between One and Two Points Perspective?

A: All lines in the image that are not vertical or horizontal disappear into one point in one…

Q: 7. What is the difference between a basic process and a secondary process? 8. What is a route sheet?

A:

Q: Hand drafting.

A: When an object features a slanted or inclined surface, it always isn't possible to point out the…

Q: What are two advantages of using a shrink-fit toolholder ?

A:

Q: Draw front and top view?

A: The Front view and Top view of the given object is drawn by third angle method of projection.

Q: oaching is an example of __________________________________. secondary machining process joining…

A: Broaching is an example of material removal secondary machining process.

Q: Q3. What is meant by joining and assembly process? Also list different types of joining and assembly…

A: Joining  and assembly process where we have to joint two material permanent or temporary on basis of…

Q: Pressing is an example of _______________________________________  process. secondary machining…

A: Pressing is an example for which process?

Q: Reduction ratio in the first and subsequent draws may not The minimum number of draws necessary will…

A:

Q: product load.

A: Determine the load produced.

Q: Manufacturing Processes How to observe various chip types formation by changing process parameters?

A: Type of chips formation in metal cutting

Q: The . view is best suited for assembly ........ drawings where both internal and external…

A: The full view is the best suited for assembly drawings where both internal and external construction…

Q: How shaper works please elaborate in 200 words

A: Shaper: It is a machine that is used to produce a horizontal, vertical, or inclined flat or plane…

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.