Discuss the effect of changing the number of bits in the output waveform. in PCM
Q: Q2: Assemble the binary bits of the "PCM" signal below into a DPSK waveform in the case of the…
A: Given, Binary bits = 10100011101 and the previous bit of the output is 1.
Q: 8086 microprocessor code for assembly language program for given requirement is carry with add two…
A: The following steps are used to write the program: 1) Store the lower order byte of both the numbers…
Q: A serial pulse train has a 70-μs bit time. What is the data rate in bits per second
A: In this question, A serial pulse train Bit time = 70-μs. What is the data rate in bits per second?…
Q: 1) Give the advantages and the disadvantages of P, PI, PD and PID controllers.
A: We are authorized to answer one question at a time, since you have not mentioned which question you…
Q: Design NOR base SR Flip flop in logic.ly website .Take screenshot of circuit and also create table…
A: For NOR gate: if the input at both the terminals is low i.e. 0 then only we get the output high i.e.…
Q: Define BPSK. How do we represent binary signals in BPSK?
A:
Q: 6) Write an 8086 assembly language program to multiply the contents of the registers CL & BL by…
A: Here, We have to multiply the contents of the register CL & BL using the repeated and then…
Q: An 8bit PCM uses mu law companding with mu=100. Calculate the signal to quantization noise ratio?
A: Pulse code modulation(PCM) is used to represent the sampled version of an analog signal in binary…
Q: In Assembely Language design the ALU that perform the following functionalities: using emu 8086.
A: The Answer :
Q: The output signal from a frequency inverter will appear on a scope screen as a: A. pure sine wave…
A: Introduction - Frequency inverter - A frequency inverter is an electrical device that accepts…
Q: Q| Write an 8086 assembly language program to multiply the contents of the registers CL & BL by…
A: Since content of register are given in register BL and register CL which are 8 bit in length so it…
Q: In a device that follows CMOS logic protocol, the power supply is +15 V. The state is considered…
A: A digital logic operates at two voltage levels. They are Logic '1' or high and Logic '0' or low.…
Q: Write an 8088/8086 assembly program that counts the length of a null terminated string that starts…
A: Microprocessor Programming : The "jargon" of directions which a specific microchip chip has is…
Q: 2.) To follow up on question 2, let's revisit an analysis you did way back in embedded systems.…
A:
Q: Q1/ If an 8-bit SAR ADC is used to digitize 8V full scale signal, what will be the digital olp for…
A:
Q: Using the concept of decoder and encoder construction, design a Programmed Logic Array (PLA) that…
A: The input-output relations are defined by the following k-maps,
Q: A 10-bit D/A converter has VFS = 5.12 V. What is the output voltage for a binary input code of…
A: Given: 10 bit D/A converter with VFS=5.12 VBinary input=1100010001
Q: Consider sampling (quantizing, digitizing) analog temperatures in the range from -17 to 17 °F. How…
A: Given, Sampling analog temperature in the range from -17 ° F to 17° F. The smallest difference…
Q: / Design and implement 3-bit binary to gray code converter using PLA
A: To design a 3-bit binary to gray code converter, Let the 3-bit binary inputs be B2, B1, and B0 and…
Q: Q5. Answer the following Design a logic circuit that detect the prime number in 4-bits binary input…
A:
Q: design 2 to 8 bit binary comparator and write it's summary?
A: 2 bit comparator A comparator used to compare two binary numbers each of two bits is called a 2-bit…
Q: When an analog signal with infinite amplitude possibilities is quantized and is given a 5-bit PCM…
A: Given, number of bits to represent each analog value (n) =5 (Since mentioned 5-bit PCM)
Q: Q4: (A)-Create an 8086 Assembly language program that subtracts two 8-bit ASCII numbers, the first…
A: First we will initialize the data segments. then move the data from the address 200 and 400 to AL…
Q: Determine at least three contemporary tools that may aid in the design of digital logic circuits.…
A: A digital circuit is often made up of logic gates, which are miniature electrical circuits that may…
Q: Briefly explain the process of generating a PCM signal
A: PCM is a digital data transmission technical but it is a wireless technique hence also know as…
Q: Q5. Design a code converter circuit that converts 2 bits binary number system to Gray code.
A:
Q: Q1: Assemble the binary bits of the "PCM" signal below into a QPSK waveform or draw the V1(t) ,…
A: According to the question, we need to draw a QPSK waveform for the given PCM code 010110111011 In…
Q: In digital design, how important are priority encoder, decoder, and multiplexer circuits? Give 3…
A: According to the question, we need to discuss the importance of the priority encoder, decoder, and…
Q: Design a 4-bit BCD to Gray Code Converter by using Programmable Array logic.
A: Programmable Array logic done by fixed OR gate and programmable AND gate.
Q: Design a logic circuit that detect the prime number in 4-bits binary input number
A: No. of inputs required four as ABCD No. of output is one as Y
Q: Derive the State table using binary numbers
A: Given state table in decimal form
Q: A system usės a 12-bit word to represent the input signal. If the maximum peak-to-peak voltage at…
A: A DAC circuit convert digital data in to equivalent analog data. A ADC circuit convert analog data…
Q: Design and implement sequential digital circuit, with following specifications: It has one input X,…
A: Given: It has one input X, two outputs Y1 and Y0. Whenever an active HIGH is observed at input X at…
Q: Q3/ Design binary adder that add three BCD numbers (1-digit) using CPAS.
A:
Q: The dynamic range of PCM is equivalent to the following; a. Number of levels -1 O b. Number of bits…
A: Dynamic range of pcm is equivalent to 2^n -1 The possible number of levels are 2^n n is no of…
Q: Q4) Starting from an initial value of R 11010101, determine the sequence of binary values in R after…
A: circular shift does not change the value of R . first we shift R logic left then in last logic right…
Q: iii) An analogue signal carries 64 bits per level. If 2000 levels are sent per second, find the bit…
A: Given: n=64 bits per level and 2000 levels per second
Q: discuss how the values of R, L , C will effect in the behavior of the output (Hint the behavior of…
A: The transfer function of standard second order system is given as: Hs=ωn2s2+2ξωns+ωn2 Where,…
Q: You are building an instrument and need to choose the ADC. The signal voltages range from –1 V to 1…
A:
Q: )Design Binary Ripple Counter using D-flipflop. ) Design asynchronous 4-bit UP-Down counter.
A: As there are two questions and it is not mentioned which question to do. So, please mention the…
Q: Design a 2-digit decade counter that counts from 00 to 59 and repeats. Use two cascaded synchronous…
A: According to guidelines we need to solve only the first question. According to the question we have…
Q: A8 bit ADC has generated a digital representation of 11001100 using the successive approximation…
A:
Q: Sketch a timing diagram of a 4-bit binary counter like the 74X163 showing the clock signal CLK and…
A: Sketch a timing diagram of a 4-bit binary counter like the 74X163 showing the clock signal CLK and…
Q: Design NOR base SR Flip flop. Take a screenshot of the circuit and also create a table of circuit…
A: S-R Flip-flop- S-K flip flop is known as a universal flip flop that is two inputs S and R. The S-R…
Q: Q2) Find the total time of execution an instruction with four machine cycle generated by 8086 MP, if…
A: The computer processes each instruction that is received. The number of steps to be followed for one…
Q: he output signal from a frequency inverter will appear on a scope screen as a: A. pure sine wave of…
A: Frequency inverter : Every inverter has a base frequency of 50 to 60 Hz a control method is used to…
Q: Give some applications for XOR, and NOR logic circuits.
A:
Q: one method of eliminating contact bounce wherein it triggers on the first contact bounce instead of…
A: To select proper answers from options.
Q: Write a preprocessor directive that sets "LEFTMOST" to be equal to the value of LEDS Would have with…
A: According to the question, we need to write a preprocessor directive that sets "LEFTMOST" to be…
Discuss the effect of changing the number of bits in the output waveform. in PCM
Step by step
Solved in 2 steps with 3 images
- Digital logic design question .An analog signal having a maximum frequency of 10 kHz is being transmitted through a PCM system with a uniform quantizer having 256 levels. What will be the minimum transmission bandwidth of the transmitted PCM signal?Logic circuit and design What is the output of Q and Q' respectively?
- Discuss the effect of changing the number of bits on the recovered analog waveformThe current output of a successive approximative type ADC is showing as 110011. If the reference voltage to the ADC is 5V, what is the corresponding analog signal voltage input to this ADC? If the ADC were of 10 bits, would the conversion time be reduced? Please answer ASAP I will like it please ASAP...An 8-Bit ADC is used to convert an audio signal ranging over 0 – 12 V. What is the RMS quantization noise associated with full-scale operation of this ADC?
- . Suggest a demodulator circuit to detect the data signal from the PSK modulated signal and design it.Write an assembly language program for 8085 microprocessor to add 2 digit BCD numbers stored in memory location C050H and C051H respectively and store the result in memory location C052H.Given a 5-bit ADC with the following reference values Vref= -2V and 12V, what is the voltage represented by the output sequence 01010?
- Q1: Design and implement an asynchronous counter that counts from 0000 up to 1100 (modulus 13). Use OR gate, and show in the drawing how the OR gate is connected to truncate the state 1101.USE DIGITAL LOGIC AND DESIGNConsider a 12 -bit ADC and full scale voltage measurement range of – 12V to + 12V. Find the resolution and % error.