Draw the influence line for RA, RB, shear @1-1, moment @1-1, shear @2-2, and moment@2-22822'30

Apply a 1 k unit moving load at a distance of x from end A.Use Equilibrium equations.

Answered: Draw the influence line for RA, RB,…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Draw the influence line for LH and LM
Draw the Influence Line Diagram for involving a moving unit load 1 unit. VD = f (x)AV = f (x)RB = f (x)
Construct the reaction influence lines .
Determine the moments at all supports. Answer key: MBA = 2 kN-m; MBC = -2 kN-m; MCB = 4.46 kN-m; MCD = -4.46 kN-m; MDC = 0.66 kN-m; MDE = -0.66 kN-m; MED = 3.27 kN-m
Draw the influence lines, a) the shear at section 1-1, b) the moment at section 1-1. Please show complete solutions.
1. The boom of the wall crane 4m long is held at right angles to the wall by a wire that is attached to the wall 3m above the foot of the boom. If the load lifted is 45000N, find the tension in the wire and the compression force in the boom Neglect the weight of the boom. Draw the FBD
Draw the influence line for member CG and interpret the diagram.
Required: Maximum positive And negative moment for 2nd-floor BEAMS DISTRIBUTION METHOD 5 cycles.
Draw the influence line for member BC and interpret the diagram.
6.D1 A large tower is to be supported by a series of steel wires; it is estimated that the load on each wire will be 13,300 N (3000 Ib). Determine the minimum required wire diameter,assuming a factor of safety of 2 and a yield strength of 860 MPa (125,000 psi) for the steel.
A vertical rectangular gate 2m wide and3 m high is submerged in water with its top edge flushedWith the water surface. Find thefollowing: 1. The value of the maximum force, F acting oncenter of pressure2. The value of the eccentricity3. The location of Force. F below the watersurface4. The magnitude of the maximum pressure
Determine the influence line for member IH and the maximum shear of member IH when a series of three concentrated loads from the truck are moving from right to left Thank you in advanced for your clear explaination :D

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Draw the influence line for RA, RB, shear @1-1, moment @1-1, shear @2-2, and moment @2-2 2 8 22' 30