Electric power is to be generated in a hydroelectric power plant that receives water at a rate of 70 m3 /s from an elevation of 65 m using a turbine–generator with an efficiency of 85 percent. When frictional losses in piping are disregarded, the electric power output of this plant is (a) 3.9 MW (b) 38 MW (c) 45 MW (d) 53 MW (e) 65 MW

Q: Water is to be withdrawn from an 11.2-m-high water reservoir by drilling a 4.1-cm-diameter hole at…

A:

Q: Consider an underground water source whose free surface is 60 m below ground level. The water is to…

A: For solution refer below images.

Q: Water in a partially filled large tank is to be supplied to the roof top, which is 8 m above the…

A:

Q: Electric power is to be generated by installing a hydraulic turbine-generator at a site 70m below…

A: Given Data The height of the turbine is: h=70 m The mass flow rate of the water is: m˙=1500 kg/s…

Q: A hydroelectric plant has a head of 57 m and a water volumetric flow rate of 500 m/s. Determine the…

A:

Q: water from Agno River is pumped using a submerged pump at an efficiency of 78% that is discharged to…

A: η=78%=0.78P=5 kWZ2=30 md1=7 cm=7×10-2 md2=5 cm=5×10-2 m

Q: Water is pumped from a lake to a storage tank 18 m above at a rate of 70 L/s while consuming 20.4 kW…

A:

Q: Seawater is to be pumped into a large tank at a rate of 165 kg/min. The tank is opwn to atmostsphere…

A:

Q: In a hydroelectric power plant as shown in the figure, 100 m3/s of water flows froman elevation of…

A: Given Volumetric flow = 100 m3/s Elevation = 130 m Overall efficiency = 0.8 % To find Electric power…

Q: Electric power is to be generated by installing a hydraulic turbine–generator at a site 120 m below…

A: Given data :H= 120 mm.= 1500 kg/s

Q: Water is pumped from a lower reservoir to a higher reservoir by a pump that provides 20 kW of shaft…

A:

Q: A fireboat is to fight fires at coastal areas by drawing seawater with a density of 1030 kg/m^3…

A:

Q: A hydraulic turbine has 50 m of head available at a flow rate of 1.30 m3/s, and its overall…

A: Given: The available head of the turbine is H=50 m. The flow rate of the water in the turbine is…

Q: The compressed air requirements of a manufacturing facility are met by a 120-hp compressor that…

A: Given data as per question Length of pipe = 9m Diameter of pipe = 22 cm = 0.22 m Flow rate = 0.27…

Q: A river flowing steadily at a rate of 167 m3/s is considered for hydroelectric power generation.…

A:

Q: The water in a large lake is to be used to generate electricity by the installation of a hydraulic…

A: Given data as per question Depth of water =50 m Water flow rate = 5000kg/s Power generated = 1862 kw…

Q: 2. Electric power is to be generated in a hydroelectric power plant that receives water at a rate of…

A: Since the question containes multiple questions. I am answering one question only so, for remaining…

Q: Water flows at a rate of 20 L/s through a horizontal pipe whose diameter is constant at 3 cm. The…

A: The data given is, Discharge, Q=20 L/s = 0.02 m3/s Pressure drop, ∆P=2 kPa=2000 Pa Water density,…

Q: Water is pumped from a lower reservoir to a higher reservoir by a pump that provides 20 kW of shaft…

A: Step-1 Given: The power of the shaft is P=20 kW. The difference in the height of the reservoir is…

Q: Well water is pumped into a tank that is 25 meters high through a pipe with an inner diameter of…

A: Given, head , h = 25 m inner diameter, d = 3.75 flow rate, q = 45 litres per min = 0.00075 m3/s…

Q: 1. A water from Agno River is pumped at 13.3 L/s using a submerged pump at an efficiency of 78% that…

A: Given: The flow rate, Q = 13.3 L/s = 0.0133 m^3/s The efficiency of pump, η = 0.75 The height of…

Q: A hydraulic turbine is used to generate power by using water in a dam. The elevation difference…

A:

Q: A water jet that leaves a nozzle at 50 m/s at a flow rate of 100 kg/s is to be used to generate…

A: Data given-  m• = 100 kg / s  V = 50 m/s

Q: A hydraulic turbine is used to generate power by using water in a dam. The elevation difference…

A:

Q: A turbine is placed at the bottom of a 20-m-high water body. Water flows through the turbine at a…

A: Given: The height of the body is H=20 m. The rate of flow of the water is V=30 m3/s. The shaft power…

Q: Electric power is to be generated by installing a hydraulic turbine-generator at a site 120 m below…

A: Hydraulic Head  of Turbine, H=120mWater flow rate, m˙=930 kg/sMechanical power output,PM=850…

Q: Q4:- Water is pumped from a lower reservoir to a higher reservoir by a pump that provides 20 kW of…

A: Given Data P=20 kW H=45 m Q=0.03 m3/s

Q: Electric power is to be generated by installing a hydraulic turbine–generator at a site 100 m below…

A:

Q: Water is to be withdrawn from an 8-m-high water reservoir by drilling a 2.2-cm-diameter hole at the…

A: Using the energy equation,

Q: Underground water is being pumped into a pool whose cross section is 3 m × 4 m while water is…

A: Given: The length of the pool is l=3 m. The width of the pool is w=4 m. The average velocity of the…

Q: Underground water is being pumped into a pool whose cross section is 6 m × 9 m while water is…

A: Given: The length of the pool is l=6 m. The width of the pool is w=9 m. The average velocity of the…

Q: Seawater is to be pumped into a large tank at a rate of 165 kg/min. The tank is opwn to atmostsphere…

A:

Q: Underground water is to be pumped by a 78 percent efficient S-KW submerged pump to a pool whose free…

A: Given:Efficiency of the pump, η=78%Power of the pump, P=5 kWH=30 mDiameter of the pipe at intake,…

Q: The drinking water needs of an office are met by large water bottles.  One end of a 0.6-cm diameter…

A: Solution: d = 0.6 cm

Q: A fireboat is to fight fires at coastal areas by drawing seawater with a density of 1030 kg/m3…

A: To find the shaft power input to the pump and discharge velocity of water Firstly to find the…

Q: Q.3) Water is pumped from a lower reservoir to a higher reservoir by a pump that provides 20 kW of…

A: Givenpower provided by pump to water P=20kWZ=45mhL=23m

Q: Consider a pipe that branches out into two parallel pipes and then rejoins at a junction downstream.…

A: Given Data: The length of both pipes is the same L1=L2. The friction factors of both pipes are the…

Q: The water in a large lake is to be used to generate electricity by the installation of a hydraulic…

A:

Q: The water is to be pumped from the lower reservoir to the upper reservoir at a flow rate of 8 kg/s.…

A: Pump  Pump is a hydraulic device which is used to lift liquid from low height to the high elevation.…

Q: Water is pumped from a lower reservoir to a higher reservoir by a pump that provides 23 kW of useful…

A: Given; Mechanical power by a pump, Pm=23 kW Head difference between reservoirs, H=57 m The flow rate…

Q: Water is pumped from a lower reservoir to a higher reservoir by a pump that provides 20 kW of useful…

A: Pump power, P=20 kW Elevation difference between the two reservoir, ∆z=45 m Water flow rate, Q=0.03…

Q: A 3-m-high large tank is initially filled with water. The tank water surface is open to the…

A: From the given data, The static suction head of the pump, hs=-3m The static discharge head of the…

Q: A D0 = 10-m-diameter tank is initially filled with water 2 m above the center of a D =…

A: Given, The diameter of the tank, D0=10 m The diameter of the valve, D=10 cm=0.1 m The length of the…

Q: Electric power is to be generated by installing a hydraulic turbine–generator at a site 110 m below…

A: Given data The height of free surface water from the turbine is h=110 m. The mass flow rate is…

Q: Q1/ Electric power is to be generated by installing a hydraulic turbine- generator at a site 120 m…

A: Given data  Available Head (H) = 120 m  Mass flow rate (m˙) = 2400 kg/s   To determine  the power…

Q: Electric power is to be generated by installing a hydraulic turbine–generator at a site 70 m below…

A: Write the height of the hydraulic turbine generator from the free-surface of a large water…

Q: A fan is to be selected to ventilate a bathroom whose dimensions are 2 m × 3 m × 3 m. The air…

A: Volume of the bathroom is v=2 m×3 m×3 m=18 m3 Volumetric flow rate through the casing is…

Q: Water is to be withdrawn from a 9-m-high water reservoir by drilling a 2.3-cm-diameter hole at the…

A: Given data as per question Height of water reservoir = 9m  Drilling hole diameter=  2.3-cm

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.