Example 7: Rocket sleds were used to test aircraft and its effects on human subjects at high speeds. It is consisted of four rockets; each rocket creates an identical thrust T. Calculate the magnitude of force exerted by each rocket (T) for the four-rocket propulsion system shown in the Figure. The sled's initial acceleration is 49 m/s, the mass of the system is 2100 kg, and the force of friction opposing the motion is known to be 650 N. Solution: H.W Free-body diagram

Example 7: Rocket sleds were used to test aircraft and its effects on human subjects at high speeds. It is consisted of four rockets; each rocket creates an identical thrust T. Calculate the magnitude of force exerted by each rocket (T) for the four-rocket propulsion system shown in the Figure. The sled's initial acceleration is 49 m/s, the mass of the system is 2100 kg, and the force of friction opposing the motion is known to be 650 N. Solution: H.W Free-body diagram

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

You construct a version of the cart and bucket, but with a slope whose angle can be adjusted. You use a cart of mass 167 kg and a bucket of mass 57.0 kg. The cable has negligible mass, and there is no friction. What must be the angle of the slope so that the cart moves downhill at a constant speed and the bucket moves upward at the same constant speed? With this choice of angle, what will be the tension in the cable?
In Fig. P3.55 the jet strikes a vane that moves to the right atconstant velocity V c on a frictionless cart. Compute ( a ) theforce F x required to restrain the cart and ( b ) the power Pdelivered to the cart. Also fi nd the cart velocity for which( c ) the force F x is a maximum and ( d ) the power P is amaximum.
The cylinder bore diameter of a double-acting reciprocating pump is 160 mm and its stroke is 340 mm. The pump runs at 53 rpm and lifts water through a height of 29 m. The delivery pipe is 22 m long and 100 mm in diameter. Find (i) the theoretical discharge in liters/s,(ii) the theoretical power required to run the pump in kW, (iii) the percentage of slip, and (iv) the coefficient of discharge., if the actual discharge is 10 liters/s. Assume the weight density of water is 9810 N/m3
A wind turbine rotates at speed of 300 rpm. What is the circumferential velocity at the tip of the blade if TSR is 2? If wind is at velocity of 7 m/s, what is the rotor radius to meet the required rpm?
A small model of a water pump with an impeller diameter of 8 in is able to develop a head of 15 ft and flow of 100 GPM when spun at 1200 RPM with a power input of 0.4 hp. If a larger model of the same pump with an impeller diameter of 24 in is to be used for another application where the required head is 80ft, at what speed (in RPM) should this larger model be ran, and at what capacity (in GPM) can it deliver water?
A cylinder with a simple spring return effect is performing compression work connected to an air network of 1.1 MPa pressure. If the diameter of the plunger is 12 cm, its stroke 4 cm and the friction force can be considered 15% of the theoretical, it is requested: a) What will be the force exerted by the stem at the beginning of the work cycle (the spring is in its natural length)? b) What will be the force at the end of the race, if the spring constant is 120 N/cm? c) What will be the air consumption under normal conditions, if you perform 10 cycles per minute?
An electric motor is accelerating a 250 kg load with acceleration of 1.2 m/s? througha gear box as shown Figure Q1(b). The rope that carries the load and spiral spring are encircled on a pulley with diameter 1.2m. Gear box ratio is 0. 1 and gear box efficiency is 100%, while gear box equivalent moment inertia is 5.55 km?. Neglect friction effect in this drive system and assume spiral spring force is X newtonCalculate the torque of the motor needed to bring up the load with acceleration1.2 m/s?.
Find an expression for the centrifugal force Fc if it depends on the mass m,the angular velocity w, and the radius R of an impeller.
A vertical circular cross-sectional jet of air strikes a conical deflector as shown in Figure G. A vertical anchoring force of 0.1N is required to hold the deflector in place. Determine the mass [kg] of the deflector. The magnitude of velocity of the air remains constant. Neglect gravity of air as well as pressure differences.
Consider an automobile with a mass of 5500 lbm braking to a stop from a speed of 55 miles/h.(a) How much energy (Btu) is dissipated as heat by the friction of the braking process?(b) Suppose that throughout the United States, 300,000,000 such braking processes occur in the course of a given day. Calculate the average rate (megawatts) at which energy is being dissipated by the resulting friction.(c) Find a source of information on the average per-capita consumption of electricity (kW) in the United States, France, and India. Roughly how many people in each country would have their electricity needs met if the braking energy calculated in Part (b) could be recovered and used to provide electricity? Show your calculations and identify your information source.
A multi-rotor propeller has a geometric pitch angle of 9 degrees at a point 0.11 m from the shaft. If the inflow velocity at this point is 3 m/s and the propeller is spinning at 2,000 RPM, what is the local angle of attack?
7. A steel pulley with a mean rim radius of 120 mm is rotated at a speed of 1100 rpm. If the mass of the rim is 5 kgs, What is the centrifugal force?