Explain the improvement of transient stability by using single pole switching? 1) it is definition 2) important of it 3)examples 4 general information about this topics

Q: What is the function, operation, and application of switching regulator?

A: Due to advancement in power electronics, in today's scenario most of the electrical appliances uses…

Q: 3. What is harmonic restrain and startup characteristic for differential protection and in which…

A: This protection system is employed to protect alternator, transformer and high rating HT motor.…

Q: Unit 4 During turn-on and turn-off of a power transistor, the current-time and voltage-time…

A: “Since you have asked multiple questions, we will solve the first question for you. If youwant any…

Q: Using a circuit diagram, describe the operation of linear shunt regulators

A:

Q: Draw the Volt-ampere characteristic curve of the device and explain.

A: V-I characteristics is the Characteristics between voltage and current. Given diode is a simple P-N…

Q: Question 8 Calculate the expression of the peak-to-peak voltage ripple of the step-up converter in…

A: It is asked to derive the expression of the peak-to-peak voltage ripple of the step-up converter in…

Q: Differences between zero current switching (ZCS) and zero voltage switching (ZVS)?

A:

Q: During turn on and turn off of a power transistor, the current-time and voltage -time relationships…

A: A switching characteristics of a power transistor is shown in the question. We need to determine the…

Q: What should the K gain value be for the system to be stable?

A:

Q: principal of improvement of transient stability by using waveform relaxation method

A: principal of improvement of transient stability by using waveform relaxation method

Q: (ii) With neat sketch explain the closed loop operation of AC -DC switched mode power supply.

A: AC-DC Switched Mode Power Supply- In buck, boost and buck-boost converter only obtain a little bit…

Q: A) Highlight the main disadvantage of the ON-OFF control.

A:

Q: If given that the switching device of the DC Power Regulator System is a thyristor, suggest a…

A:

Q: Describe the effect the switching control signal frequency has on the output voltage and current of…

A: There is a reasonable effect of switching control signal frequency on the output voltage and current…

Q: the Starting Up the Power Station Simulator Give a n example of faults that require giving a signal…

A:

Q: When it comes to switching activity, what do the on and off states of a bipolar junction transistor…

A: When it comes to the switching activities of the bipolar junction transistor. When it is On state,…

Q: 3. Why the copper loss in the primary can be neglected, in the open circuit test?

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: What is the ripple factor and what causes it? Discuss and explain how this factor can be used as a…

A: When a sinusoidal voltage is converted into dc, the output voltage waveform inherently contains…

Q: Discuss about Power Thyristor's DC and Ac switching.(with Diagram)

A: Power Thyristor DC circuit is as follows: - This basic "on-off" thyristor terminating circuit…

Q: Explain the operation of the circuit by drawing the AC power control (regulation) circuit with the…

A: AC power control circuit:

Q: What are the main resion inside System verilog simulation in time step?

A: Verilog is Hardware Description language . The memory and array declaration in Verilog is static in…

Q: What is Adaptive control system? If the process characteristics are not well known then what type of…

A: Adaptive control system is the control method which is used by a controller and which must adapt to…

Q: Draw the Circuit diagram for Constant and continuous load current. Explain its working.

A: This question is from "POWER ELECTRIC DRIVES AND TECHNIQUES". We are going to study how to regulate…

Q: Explain the operating principle of power factor correction circuit that can shape the AC input…

A: Power factor correction circuit: In electrical system many loads are connected  some are highly…

Q: Discuss common mode rejection ratio. Common mode rejection is desirable or undesirable?

A: The objective is to determine common mode rejection ratio.

Q: Determine delay angle when system is most efficient.

A: Given R1=20 kΩ R2=0 to 120 kΩ C=0.22 μF Vs =220 V f=60 Hz diac breakdown voltage =18 V

Q: a.What is an ROC?

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: Choose the converter which is used for converting Fixed bi-directional voltage to Variable…

A: We need to tell which option is correct for the given statement.

Q: What are the different turn on methods of SCR?

A:

Q: ii. The generation voltage is in simulator is ...Volts.

A: In the simulator, the generation voltage and current source are showing on the display of the LED of…

Q: a) When does an E-MOSFET act as an open switch? b) When does an E-MOSFET act as a closed switch? c)…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: What is voltage stability?

A: According to question, we need to explain the voltage stability.

Q: c) When considering thyristor switching why is Isolated Gate Control needed ?

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: (i)What do you mean by DAC ? (ii)List out the types of ADC .Also mention about the type of ADC which…

A:

Q: Explain the meaning and give a practical significance of the unit step signal and ramp signal

A: Unit step signal  The unit signal is given by the mathematical expression as shown below:  f(t)=0 if…

Q: What is voltage regulator?

A: The electronic devices we use in our life have some power ratings, voltage rating and current…

Q: What isolated switching mode power supply should be used and what would ripple voltage and ripple…

A: SMPS-Switch mode power supply. It is a device which is used to switch at high frequency and works as…

Q: Q#3 : How transient stability limit can be increased?

A: Methods to improve transient stability : Using high speed circuit breaker :       It increase the…

Q: Which IC technology has the lowest power dissipation in general?

A:

Q: To demonstrate the operation, characteristics and design of a saturated bipolar transistor switch

A: The given circuit can be designed and analyzed using a Multisim workbench.

Q: In class C operation, the operating point is generally located above cut off point + of the DC load…

A: Bartleby has policy to solve only first question. For rest questions re-upload.

Q: Explain the various modes of operation of converter which is used in power electronics circuits to…

A: Static converters are electrical networks mainly composed of semiconductor devices operating in the…

Q: Is the computed average percent error more or less than the tolerance of the resistors? Explain why.

A: Note : the tolerance values of resistances are not given. We assume each resistance has 1 %…

Q: Write about fault tolerance.

A: We have given the following problem Write about fault tolerance.

Q: What is NEC and what is the purpose of it? Does it present the maximum standard or the minimum?

A: NEC stands for National Electrical Code and it provides some basic standards and requirements which…

Q: Write about computer simulation of ASSESSING THE TRANSIENT STABILITY.

A: Transient Stability- It is defined as the ability of the power system to return to its normal…

Q: State whether the following statement is true or false. “When an LDO is used as an auxiliary current…

A: LDO- low dropout regulator