Question

explain the working of CPI FFH instruction of 8085 microprocessor.

Expert Answer

Want to see the step-by-step answer?

Check out a sample Q&A here.

Want to see this answer and more?

Experts are waiting 24/7 to provide step-by-step solutions in as fast as 30 minutes!*

*Response times may vary by subject and question complexity. Median response time is 34 minutes for paid subscribers and may be longer for promotional offers.
Tagged in
Engineering
Electrical Engineering

Digital Electronics

Related Electrical Engineering Q&A

Find answers to questions asked by students like you.

Q: what do you call an equipment that changes the voltage higher or lower without changing the frequenc...

A: =>  Capacitor  bank :- It is used to improve the power factor of the system.  =>  Switchgear :...

Q: It has been estimated that a minimum run-off of approximately 94 m3/sec will be available at a hydra...

A: Given: Head, H=39 m Minimum run-off is approximately 94 m3/sec.  

Q: Transmission and Distribution of Electric Power Answer the Following Question Please: Q) Three-phase...

A: Click to see the answer

Q: • Solve for the value of constant(C) by obtaining the orthogonal trajectory of the given equation be...

A: Click to see the answer

Q: Question:5 The full wave rectifier with filter is given, calculate: Do Filtered output V. "Drip-p) R...

A: The peak to peak ripple voltage is the difference between the maximum voltage and the minimum voltag...

Q: The emitter current is always (a) greater than the base current (b) less than the collector current ...

A: The relation between emitter, collector and base current of a BJT is given as IE=IC+IB Where, IE is ...

Q: Consider the circuit in the given figure. Assume R1 = 130 Ω and R2 = 310 Ω.   Calculate current i in...

A: We can find current easily by using ohms law , i.e I=V/R

Q: I:06)

A: Click to see the answer

Q: Describe the different types of memories and their applications.

A: The following general types of memory module can be used in an embedded system. 1.Volatile Memory 2....

Q: 1. Compare the output waveform for Half-Wave Rectifier with and without capacitor. Compare the outp...

A: Note:  As per our honor code, we are authorized to answer only one question at the moment. If you wa...

Q: Find the transmission parameters for the two-port network shown in the figure below. I1 jin I2 V1 キ4...

A: Click to see the answer

Q: Question 3: Find the convolution of below signals. 2 1 -1 -2 -1 -0.5 0.5 1 1.5 2.5 3 t (sec)

A: Click to see the answer

Q: 4.12 Use the mesh-current method to find the power dissipated in the 1 N resistor in the cir- cuit s...

A: Click to see the answer

Q: State the equivalent transfer function of the system in Figure 2.

A: Click to see the answer

Q: what switch type and rating is required to control five 300 watt tugsten filament lamps on a 120 vol...

A: Click to see the answer

Q: Explain why voltage spikes and surges are high-frequency occurrences.

A: Voltage spikes and surges in a circuit occur when there is a sudden release of energy stored in vari...

Q: Q2 and Q3 were collect. Please please help me.

A: To find the current through R4 and capacitor 

Q: Specify the register contents and flag status as the following instructions are executed.   A ...

A: The MVI and MOV instruction does not affect any flags. It is a data transfer operation. The RRC inst...

Q: How can I find the solutions for this problem? (answers are given) Answers: a.i. Eth = 4 V, Rth = 3....

A: Click to see the answer

Q: A three-phase, two-pole, 60-Hz induction motor is observed to be operating at a speed of 3502 r/min ...

A: Given values are - Pin=15.7kWI=22.6AStator resistanceRs=0.2OhmP=2f=60HzNr=3502

Q: A  500kVA, three phase transformer has iron losses of  300W and full load copper losses of 600W. Cal...

A: The relation between the copper loss and the iron loss for the maximum efficiency of the three phase...

Q: three (3) incadescent lamps are connected to 220 V source. Each lamp draws 0.815 A. what is the amou...

A: Voltage across each incandescent lamp =220V  (assume that bulb are connected in parallel combination...

Q: Although current is blocked in reverse bias, (a) there is some current due to majority carriers (b) ...

A: When a pn junction diode is reverse biased, then the height of the junction potential barrier increa...

Q: Perform nodal analysis on the following circuit: (Equations only. You do not have to solve.) The nod...

A: Given Circuit,

Q: (1) A full adder in which:  SUM = C' (AB' + A'B) +C (AB + A'B')   (2) CY = AB + BC + AC

A: The truth table for the given full adder is given as  A B C Sum Carry 0 0 0 0 0 0 0 1 1 0 0...

Q: Find I and V in the given circuit. Assume A = 4 A, B = 11 A, and C = -5 A.   The current and voltage...

A: Click to see the answer

Q: a sine wave has a maximum value of 230 v. what is the voltage after 38° of rotation

A: Click to see the answer

Q: A hydroelectric power station is supplied from a reservoir having an area of 50 km2 and ahead of 50 ...

A: Click to see the answer

Q: What will be the output of the following circuit? (Assume 0.3v drop across the diode) 1BH62 V1 12 V

A: Given data, The value of voltage is V1 = 12 V. The value of diode voltage is VD = 0.3 V. Apply KVL...

Q: 50 KVA, 34.5 kV/380V of y/y-connected, three- phase transformer internal parameters R1= (16/10) 0/ph...

A: Click to see the answer

Q: We have already noted two sources of systematic error in the use of this method: not enough sample t...

A: Click to see the answer

Q: v Part 4: Complete Response of a 2nd Order Circuit X Incorrect. You will need to find the current th...

A: In the given circuit: Find v(t) for t>0 for the circuit  when v(0)=4 V and il(0)=0 A: Draw the ci...

Q: Find the Laplace transforms of the following time functions. using the Laplace transform definition ...

A: To find the Laplace transform using Integration method

Q: 3 A sequential circuit has three flip-flops A, B, C; one input Xin ; and one output Yout . The state...

A: We are authorized to answer one question at a time, since you have not mentioned which question you ...

Q: Power spectral density of a signal is given f Ogp(f) = e 20 W/Hz Accordingly, the power spectral den...

A: Click to see the answer