Covernt from English to Metric Units. Your final answer should be in Metric Units. Write your step by step solutions. F4-1. Determine the internal normal force, shear force,and bending moment acting at point C in the beam.10 kN20 kN-m-2 m-F4-1

Answered: Image /qna-images/answer/56b078b8-56c4-42eb-a15e-a3eb57f3ed36.jpg

Answered: F4-1. Determine the internal normal…

Engineering

Civil Engineering

F4-1. Determine the internal normal force, shear force, and bending moment acting at point Cin the beam.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. The strongback or lifting beam is used for materials handling. If the suspended load has a weight of 2 kN and a center of gravity of G , determine the placement d of the pad eyes on the top of the beam so that there is no moment developed within the length AB of the beam. The lifting bridle has two legs that are positioned at 45°, as shown.
The strongback or lifting beam is used for materials handling. If the suspended load has a weight of 2 kN and a center of gravity of G, determine the placement d of the padeyes on the top of the beam so that there is no moment developed within the length AB of the beam. The lifting bridle has two legs that are positioned at 45°, as shown.
Draw the envelopes for maximum shear and moment in a 24-ft-long simply supported beam produced by a live load that consists of both a uniformly distributed load of 0.4 kip/ft of variable length and a concentrated load of 10 kips (Figure P12.42). The 10-kip load can act at any point. Compute values of the envelope at the sup- ports, quarter points, and midspan.
Determine the Moment Capacity of the section if fb≤280MPa.
For the beam and loading shown, specify (a) the absolute value of the reaction force in B in units |RB| kN, (b) the absolute value of the displacement at the midpoint D of the BC part of the beam in units |yD| mm. Take the P value in the question 15 kN and the W value 34 kN/m. E = 200 GPa and I = 34.4 x 10-6 M4.
Determine: a)Maximum Moment and b)Maximum Shear on the 20 meters long simple beam due to the wheel loads of a moving HS15-44 truck. Calculate and round-off to 2 decimal places.
A 9 − meter simply supported T-beam carries a concentrated load of 10 kN at3 meters from the left support and 16 kN at 3 meters from the right support. Overall depth ofbeam is 400 mm and the location of the neutral axis is 116.542 mm from the top of the beam.Moment of inertia is equal to 210.358 × 106 mm4 A. Determine the maximum moment using shear and moment diagram.B. Determine the locations of 40 kN. m from the left support.C. Calculate the flexural stress.
The overhanging beam shown supports the given ultimate load Wu= 5okN/m. The section is 300mm by 500mm rectangular beam having f'c=35MPa, fy=420 MPa, stirrups diameter = 10mm and concrete cover 40mm. a.) the area of steel reinforcement corresponding to rho max in mm2.b.) the location of the point of zero shear in the beam measured from the left support B in mm.c.) Calculate the maximum positive moment in the beam in kN.m.d.) Calculate the required reinforcement Asreqd corresponding to the maximum positive moment in mm2.e.) Calculate the depth of the compression block of the final positive moment section in mm.f.) Calculate the depth of the neutral axis of the final positive moment section in mm.g.) What is the ultimate moment capacity of the final positive moment section in kN.m.h.) Calculate the additional positive moment that can be imposed to the beam without exceeding the moment capacity of the final positive moment section in kN.m.
Find the deflection at the center and slope at the ends for a beam 8m long simply supported at ends and carrying a U.D.L of 4 kN/m over whole of its span and a central concentrated load of 8 kN. Take E = 200GN/m² and I = (10^-4) m^4.
A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall transverse to the given beam. Answer the following questions given the sections of the beam. Calculate the depth of the neutral axis of the section in PART A in mm.0 Calculate the ultimate moment capacity of the section in PART A in kN.m.0 Calculate the effective depth of the section in PART B in mm.0
5.13. A beam of 11 in. width and effective depth of 16 in. carries a factored uniformly distributed load of 5.3 kipsyft, including its own weight, in addition to a central, concentrated factored load of 12 kips. It spans 18 ft, and restraining end moments at full factored load are 137 ft-kips at each support. It is reinforced with three No. 9 (No. 29) bars for both positive and negative bending. If f c = 4000 psi, through what part of the beam is web reinforcement theoretically required ( a ) if Eq. (5.12 d ) is used and ( b ) if Eqs. (5.12 a ) through (5.12 c ) are used? Comment. 5.14. What effect would an additional clockwise moment of 176 ft-kips at the right support have on the requirement for shear reinforcement determined in part ( a ) of Problem 5.13? 5.15. Design the web reinforcement for the beam of Problem 5.13, with V c determined by the more approximate ACI equation, using No. 3 (No. 10) vertical stirrups with f y = 60,000 psi.
Determine shear and moment equations of the beam shown. Neglect horizontal reactions since there are no axial forces. Summarize the equations solved.Example: Section 1: V1:M1: