Figure (a) shows the Full-bridge rectifier that supplying the highly inductive load and figure (b) show the input current of rectifier. Input voltage and Load current as follow: Id=80 A v, = v7 220 sin wt V If the delay angle a=80 and Ls=1.2 mH ,Calculate The X1 and X2 in degree ,(1) さ。 1,(0) 1,() v,(1) のさ。 X2 X1 O X1=80,X2=85 O X1=36,X2=80 O X1=36,X2=75 O X1=60,X2=80

Figure (a) shows the Full-bridge rectifier that supplying the highly inductive load and figure (b) show the input current of rectifier. Input voltage and Load current as follow: Id=80 A v, = v7 220 sin wt V If the delay angle a=80 and Ls=1.2 mH ,Calculate The X1 and X2 in degree ,(1) さ。 1,(0) 1,() v,(1) のさ。 X2 X1 O X1=80,X2=85 O X1=36,X2=80 O X1=36,X2=75 O X1=60,X2=80

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 1PA: You are working as an electrician in a large steel manufacturing plant, and you are in the process...

See similar textbooks

Similar questions

For residential water heaters, the Consumer Product Safety Commission suggests a maximum temperature setting of ___________ F (_____________ C). Some states have laws stating a maximum temperature setting of ____________ F (________________ C).
An office building uses a bank of 63 lead-acid cells connected in series with a capacity of 80 amp-hours each to provide battery backup for their computers. The lead-acid cells are to be replaced with nickel-metal hydride cells with a capacity of 40 amp-hours each. How many nickel-metal hydride cells will be required to replace the lead-acid cells and how should they be connected?
You are working as an electrician in a large steel manufacturing plant, and you are in the process of doing preventive maintenance on a large DC generator. You have megged both the series and shunt field windings and found that each has over 10 M to ground. Your ohmmeter, however, indicates a resistance of 1.5 across terminals S1andS2. The ohmmeter indicates a resistance of 225 between terminals F1andF2. Are these readings normal for this type machine, or is there a likely problem? Explain your answer.
power electronics A fully-controlled three-phase bridge rectifier is supplied at 415 V ,50 Hz, the supply source inductance being 0.9mH. Neglecting resistance and thyristor volt-drops. Determine the mean load voltage at firing delay angle of 30∘
Calculate the percent ripple for the voltage developed across a 120-microFarad filter capacitor when providing a load current of 80 mA. The full-wave rectifier operating from the 60-Hz supply develops a peak rectified voltage of 25 V.
2. Connecting a capacitor at the output of a rectifier will serve as a a) Filter b) Charge storage device c) Bypass capacitor d) non of the above 3. In a half-wave rectifier , peak value of the output waveform is always a) Equal to the input wave b) Higher than the input wave c) Less than the input wave d) it depends upon diode 4. RMS value calculation involves which of the foolowing steps. a) Square root of all the values, taking mean, and then squaring b) Squaring all the values, taking means and then square root c) Squaring all the values, sqauare root them,and then taking means d) none of these 5. In full-wave rectifier, peak value of the output wave is always. a) Equal to the input wave b) Higher than the input wave c) Less than the input wave d) it depends upon the diodes
Choose the correct answer 1. Increasing the value of a resistor in an RC circuit at the output of a rectifier will result in a)Smooth DC output b)Distorted DC output c)Output will not be a pure DC d)No effect 2. Connecting a capacitor at the output of a rectifier will serve as a a) Filter b)Charge storage device c)Bypass capacitor d)None of the above 3. In a half-wave rectifier, peak value of the output waveform is always a) Equal to the input wave b) Higher than the input wave c) Less than the input wave d) It depends upon the diodes 4. RMS value calculation involves which of the following steps a) Square root of all values, taking mean, and then squaring b) Squaring all the values, taking mean, and then square root c) Squaring all the values, square root them, and then taking mean d) None of the above 5. In a full-wave rectifier, peak…
A three-phase bridge rectifier uses diodes rated at IdRMS = 145, VRRM =1000V and VD=0.7V. The rectifier isfed from a transformer with an inductance of 0,5mH per phase. Assume infinite inductive filtering and calculate, 1. the maximum DC output current;2. the maximum DC output voltage;3. the overlap angle.
A FW rectifier is required to deliver 48VDA with 10% ripple on a 7.5Ω resistor. a)Identify the capacitor providing these values (capacitance and ripple current - ripple current). b)Identify the necessary welding transformer for 120VAA 60Hz welding.c) Find the required serial inductance value for continuous current withdrawal from the source
1. A certain full-wave rectifier has a peak output voltage of 30V. A 50 mF capacitor filter is connected to the rectifier. Calculate the RMS ripple developed across a 600 W load resistance 2. It is a process of allowing electric current to flow only in one direction that is changing A.C in to D.C.
Design a 15 V Zener regulator for the following conditions: 1) The load current IL ranges from 200 mA to 300 mA.2) The source voltage ranges from 21 V to 25 V. Based on your design results,a) Draw the Zener regulator circuit.b) Calculate the power ratings for both Zener diode and resistor Ri
Provide a complete solution 1.) A full-wave rectifier (operating from a 60-Hz supply) drives a capacitor-filter circuit (C = 100 uF), which develops 12 V dc when connected to a 2.5-kiloOhms load. Calculate the output voltage ripple. (answer= 0.12 V rms) 2.)A full-wave rectifier operating from the 60-Hz ac supply produces a 20-V peak rectified voltage. If a 200-uF capacitor is used, calculate the ripple at a load of 120mA