Answered: Find the reading of the device for…

Find the reading of the device for tensile testing of cement mortar in the unit KN if the cement mortar's tensile strength is 1.5Mpa and the dimensions of the failure section are (2 * 2.3) cm?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.6.7P: A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The...

See similar textbooks

Related questions

Q: A hollow cylindrical rod with a diameter of 100mm and a thickness of x tensile load of 12.5 kN. Find…

A: Given data:

Q: An aluminum alloy has a modulus of elasticity of 70 kN/mm^2 and yield strength of 275 N/mm^2…

Q: Find stress of a aluminum cylinder of diameter 12.8mm and gauge length 50.8mm. The force applied is…

Q: 1. A tensile test is carried out on a specimen of mild steel of gauge length 40 mm and diameter 7.42…

A: Given: To find various properties of metal using test data.

Q: When a circular hole of diameter 40 mm is punched out of a 1.5 mm thick metal plate, the shear…

Q: Find the final length of the bar of an aluminum alloy with a modulus of elasticity of 68.8 GPa,…

Q: A high-density polyethylene [E = 128 ksi; a = 88 x 10-6/°F] bar is positioned between two rigid…

Q: If the ultimate strength of a steel rotating-beam test specimen was around 1600 MPa. Estimate the…

Q: A copper specimen of Young's Modulus 129 GPa is subjected to a tensile test in a laboratory and the…

A: Given data The initial length of specimen (Li) = 396 mm The initial diameter of the specimen (Di) =…

Q: The data shown in the accompanying table are From a tensile test of high-strength steel. The test…

Q: A Copper specimen of circular cross-section is subjected to a tensile test. The data obtained are:…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: the 62 MPa stress level what would be the total creep after 500 hours? Consider that t cerial is…

Q: A steel rotating-beam test specimen has an ultimate strength of 1600 MPa. Estimate the life of the…

A: Given data: Ultimate strength Sut = 1600 MPa Stress amplitude σa = 900 MPa First we calculate the…

Q: Stress strain behavior of a cast iron with a diameter of 15.8mm and gauge length of 60.80mm is shown…

A: Given Stress strain graph L =60.8 mm Diameter 15.8 mm to find Percentage elongation

Q: A cylindrical bar of metal having a diameter of 18.8 mm (A=278 mm^2) and a length of 198 mm is…

A: Bar diameter, d=18.8mm=0.0188m Cross sectional area of the bar, A=278mm2=0.000278 m2 Length of the…

Q: A 0.013 m diameter, 0.5 m long cylindrical metal bar is subjected to a compressive force of 8,500 N.…

Q: Tensile stress-strain diag 450 400 350 300 250 200 150 100

A: given:

Q: See the set of bars for made of a material that has a yield strength of 350 MPa, determine the…

Q: Q3) The figure below simplified a load-elongation diagram of a tensile test for low carbon steel…

A: Solution: Yield point is the point on the stress vs strain or the load vs elongation curve where a…

Q: 2. Ten point load tests are carried out on cylindrical specimens of a sedimentary rock with 30 mm…

A: The given values are as follows, If P =200kN Cross sectional Area=6000mm2 To Determine The stress…

Q: A 8mm diameter rod, of unknown material, is subjected to 50kN tensile load. In the process, its…

A: GIVEN DATA Diameter d=8mm Load P=50KN Initial length =300mm final length = 303mm

Q: A cylindrical specimen of steel having an original diameter of 12.8 mm (0.505 in.) is tensile tested…

A: Consider a specimen having initial cross-sectional and final cross-sectional area be A0 and Af…

Q: when the applied tensile stress is 150 MPa , and the affected force is 7540 N, find the .diameter of…

A: Write the formula for tensile stress on the specimen with a circular cross-section in terms of the…

Q: Find the equivalent stresses at Points 1 and 2 of the element with given geometry and loading…

A: Given, Shaft diameter, d=20 mm=0.020 m Shaft length, L=120 mm=0.12 m F1=750 N F2=3000 N Torsion,…

Q: strain scale of 1 in.=0.001 in./in. stress. Use a scale of 1 in. = 20 ksi and 1 in. = 0.05 in./in.…

Q: 3.33 The following data are obtained from a tensile test of a 12.7-mm-diametler aluminum specimen…

A: Given Specimen length = 50 mm Specimen diameter = 12.7 mm Specimen final diameter = 8.8 mm To find…

Q: 1.4-7 The data shown in the table below were obtained from a tensile test of high-strength steel.…

A: Only one question can be answered according to the rules. Kindly upload the other question to be…

Q: 1. Draw the graph of stress against strain 2. Discusses the obtained results 3. From the graph find.…

Q: A spherical pressure vessel 400-mm in diameter has a uniform thickness of 6 mm. The vessel contain…

A: To Find : The Factor of safety with respect to tensile failure . Given : The diameter is D=400 mm.…

Q: Stress-Strain curve of a steel with an initial diameter of 8 mm and initial length of 35 mm.…

Q: Question 1. A rod is 3 m long at a temperature of 15°C. Find the expansion of the rod, when the…

Q: Given: Stress-Strain curve of a steel with an initial diameter of 8 mm and initial length of 35 mm.…

Q: A circular rod of diameter 16 mm and 500 mm long is subjected to a tensile force 40kN. The modulus…

A: Given, The diameter of the rod, d=16 mm The length of the rod, L=500 mm The load, P=40 kN=40000 N…

Q: A specimen of steel 20 mm diameter with a gauge length of 200 mm is tested to destruction. It has an…

Q: Q.1: Ifa material is cast iron (ultimate tensile strength = 300 Mpa, ultimate compressive strength -…

A: Data given- Ultimate tensile strength = 300 MPa Ultimate compressive strength = 900 Mpa

Q: The yield stress for mild steel is 207MP.. A specimen with diameter of 0.01lm and length of 0.1m is…

Q: A single ply of a certain graphite-epoxy composite with fiber oriented at 60° is in a planer state…

A: INTRODUCTION: The principal place is considered where the principal stress is acting and the…

Q: A tensile test is peformed on a brass specimen 10 mm in diameter using a gage length of 50 mm (see…

A: Data given- P = 20 kN ∆L = 0.122 mm L = 50 mm

Q: A tensile test is conducted on a mild steel bar. The following data was obtained from the test :…

A: Given that, Diameter of steel bar, d=3 cm,Gauge length of the bare, L=20 cm,Load at elastic limit,…

Q: Suppose that an axle component of an automobile is fabricated from steel alloy with a plane strain…

A: It is given that Suppose that an axle component of an automobile is fabricated from steel alloy…

Q: A circular rod of diameter 8 mm and 300 mm long is subjected to a tensile force 20 kN. Take E =…

A: Given data:

Q: 200 stress 150 (MPa) 100 50 0.1 0-2 strain From the tensile stress-strain behavior for the brass…

Q: At a temperature of 80°C, a steel tire 12 mm thick and 90 mm wide that is to be shrunk onto a…

A: Given Data: Initial temperature, T1=80 C Final temperature, T2=25 C

Q: De ter mia the tensile and Compresnu stress for the bea shown in fig 160 lo wlm 2. m 20 mm 120 I =…

Q: From the tensile stress-strain behavior for the brass specimen ,P the diamcter is 12-8 mm Calculate…

Concept explainers

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.

Question

Find the reading of the device for tensile testing of
cement mortar in the unit KN if the cement mortar's
tensile strength is 1.5Mpa and the dimensions of the
failure section are (2 * 2.3) cm?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Types of Properties of Engineering Materials

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
A specimen of titanium alloy is tested in torsion and the shear stress–strain diagram is shown in Fig.a. Determine the shear modulus G, the proportional limit, and the ultimate shear stress. Also, determine the maximum distance d that the top of a block of this material, shown in Fig. b, could be displaced horizontally if the material behaves elastically when acted upon by a shear force V. What is the magnitude of V necessary to cause this displacement?
Find the final length of the bar of an aluminum alloy with a modulus of elasticity of 68.8 GPa, whose initial length l0 is 1.9 m when a tensile stress of 208.0 MPa is applied.
While testing on a metallic rod, it is observed that the fiamedia of rod is reduced by 0.0025mm under the axial pull of 20KN. the original diameter of is15mm.if modulus of rigidity of rod metal is 50KN/mm.find the young's modulus and bulk mofumod
A 200 x 100 x 50 mm steel block is subjected to a hydrostatic pressure of 15 MPa. The Young's modulus and Poisson's ratio of the material are 200 GPa and 0.3 respectively. What is the change in the volume of the block?
When an object is placed underwater, the pressure on the object is subjected to uniform stress on all sides. a) define volume strain, the bulk modulus, compressibility, and the relationship between the bulk modulus and compressibility. b) A 100 litre volume of liquid is subjected to a 2000 psi increase. If the compressibility of the liquid is 5 x 10-5 per atm, find the bulk strain and absolute decrease in the volume of the liquid c) explain the concepts of shear stress and shear strain? could these concepts be applied to the fluid problem above?
Data taken from a stress-strain test for a ceramic are given in the table. The curve is linear between the origin and the first point. Plot the diagram, and determine the modulus of elasticity and the modulus of resilience.
Find the Young’s modulus (Y) of the steel rod of 1 m long and a cross sectional area of 0.05 cm2, elongates 2% when supported by a 120 kg load, hung from the other end.
Experiments were conducted in a tension testing machine to evaluate the material properties of two metallic rods both having diameter equal to 10 mm. First rod having modulus of rigidity of the material equal to 400 tonnes/cm2 when subjected to an axial tensile force of 6 kN, the change in its diameter was observed to be 0.0018 cm. The value for the bulk modulus of the second metallic rod is same as that of the first one but modulus of elasticity 18% more. Based on the material properties calculate and compare the values of different moduli as well as Poisson’s ratio for both metallic rods. Justify your answer with reasons.
The femur, the long bone in the thigh, can be modeled as a tube of compact bone for most of its length. The cross-section area of the compact bone in the femur of a 70 kg person is 4.8 x 10-4 m2, a typical value.a. If this person supports his entire weight on one leg, what fraction of the tensile strength of the bone does this stress represent?b. By what fraction of its length does the femur shorten?
The ply stress σα was calculated for AS1/3501-6 Graphite/Epoxy laminates [0/+-45]s under load with N1=10,000 N/m and N2=N6=0. When the strength of this material is as follows, determine the stability of the laminate according to the maximum stress theory.
The deformation response of a certain polymer canbe described by the Voigt model. If E = 400 MPa and η = 2 x 1012 MPa-s, compute the relaxation time. Compute e(t)for times to 5T when the steady stress is 10 MPa. How muchcreep strain takes place when t = T and when t = ∞?