For a given short transmission line of impedance R+jX ohms/phase, the sending end and receiving end voltages Vs and Vr are fixed. Derive the expression for the maximum power that can be transmitted over the line

For a given short transmission line of impedance R+jX ohms/phase, the sending end and receiving end voltages Vs and Vr are fixed. Derive the expression for the maximum power that can be transmitted over the line

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.36P

See similar textbooks

Related questions

Q: A lossless transmission line having 50 Q characteristic impedance and length 4 is open circuited at…

A: It is given that: Zccharacterstic impedance=50ΩVgLoad voltage=3VZgLoad impedance=20Ω

Q: A 230-kV, three-phase transmission line has a per phase series impedance of z = 0.05 + j0.45 Ω per…

A: Given 230-kV z = 0.05 + j0.45 Ω per Km y = j3/4 × 10−6 siemens per km. It delivers 200 MVA, 0.8…

Q: A single-phase, 50 Hz, 120 km transmission line delivers 50 MVA at 0.86 lagging power factor at 132…

A: Nominal T- Network of a medium transmission line: Given: To find:

Q: The sending-end and receiving-end voltages of a three-phase transmission line at a 200 MW load are…

A: According to the question we have to find the value of the maximum steady-state power that can be…

Q: A 3-0, three wire CBA system, with an effective line voltage 200 V, has a balanced A. Connected load…

A: In this question we need to find a line and phase current of given three phase system.

Q: Open and short cirauit termination measurements on a telephone cable 50 Km long, at an angular…

Q: 2. A balanced load of 30 MW is supplied at 132 kV, 50 Hz and 0-85 p.f. lagging by means of a…

A: Balance 3 phase system. Load is 30MW, 132kV at 0.85 PF lagging. Impedance of transmission line =…

Q: 2. A balanced load of 30 MW is supplied at 132 kV, 50 Hz and 0-85 p.f. lagging by means of a…

Q: transmission

Q: Three-phase transmission line 90 km long Line impedance z=(0.4+j0.9) ohm/km, If the power Pr=60 MW…

Q: line

Q: C- Find the formulas of the ABCD constants considering the model of a medium length transmission…

Q: In relation to AC transmission system, (a) Assuming a lossless short line has a reactance of X,…

Q: A 3 phase line having an impedance of (5+j20)ohm per phase delivers a load of 30MW at a power…

A: It is given that: Z=5+j20 Ω =20.61∠75.96° Ωso, R=5 Ω and X=20j Ωcosϕ=0.3Y=0 (neglected)V=33 KVSo,…

Q: For a transmission line, the value of the open circuit and short circuit impedance are 100 ohm and…

A: If ZOC is the open circuit input impedance and ZSC is the short circuit input impedance of a…

Q: 3. If a transmission line with an impedance characteristic of 50 ohm is connected to a load with an…

Q: 2. A balanced load of 30 MW is supplied at 132 kV, 50 Hz and 0-85 p.f. lagging by means of a…

A: The answer value given with the question is incorrect. The solution can be achieved as follows.

Q: A load of 145 MW at a power factor of 0.9 lagging can be delivered by a 3-phase transmission line.…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: The ABCD constants of a lossless three-phase, 500-kV transmission line are A = D = 0.86 + j0 B = 0 +…

A: Solution (a) 3 Vr Ir =1000x106Ir = 1000 x106 x1033x500x103 =1154. 7 A (0.8-j0.6)Vs = AVr+BIr…

Q: A single phase short-transmission line is feeding a load of 12 kW at a 0.8 lagging power factor. The…

A: Given values are - PL=12kWcosϕ=0.8R=5ohmX=10ohmVL=440∠0oV

Q: A 230-kV, three-phase transmission line has a per phase series impedance of .... (please see…

A: We only answer the first three parts of a question on this platform, unless specified otherwise.…

Q: A 60 Hz, single-circuit, three-phase transmission line is 150 mi long. The line is connected to a…

Q: 13] A transmission line circuit consists of an air transmission line of length 175.752 and…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: The magnitudes of the open circuit and short circuit input impedances of transmission line are 100…

A: Characteristic impedance (Z0) of a transmission line is defined as the impedance of the transmission…

Q: The per-phase constants of a 345-kV, three-phase, 150-km-long transmission line are resistance = 0.1…

A: we need to determine the sending-end voltage.

Q: A three phase transmission line is 390 km long. The series impedance of the line is (0.315+ j0.653)…

A: Given: A three-phase transmission line is 390 km long. The series impedance of the line is Z=(0.315+…

Q: has V, = 15/0° Vm Z, = A 40-m-long transmission line shown in Figure 30 + j60 N, and V, 5/-48° Vms…

Q: A 60-Hz, 230-km, three-phase overhead transmission line has a series impedance z = 0.8431/79.04°…

A: Overhead Power Line: An overhead power line is a structure that transmits electrical energy across…

Q: In a mismatched transmission line with intrinsic impedance of Z, and with a load of impedance of Z,,…

A: A quarter-wave transformer is a basic impedance transformer used in impedance matching to reduce…

Q: A 40-km, 220-kV, 60-Hz three-phase overhead transmission line has a per-phase resistance of 0.15…

Q: A lossless transmission line with characteristic impedance of 500 is an unknown load is terminated…

A: According to the question we need to calculate the value of load impedance.

Q: The char. impedance of the trans. line is 50-Ohm and the resistance of it is 0.1Ohm/meter. What will…

A: For the distortion less transmission line the attenuation constant is independent of the frequency.…

Q: A short 3- line with an impedance of (6 + j8) N per line has sending and receiving end line voltages…

A: Given a short 3-φ line with, Impedance per line, Z = (6 + j8) Ω Resistance, R = 6 Ω Reactance, X = 8…

Q: A single-phase transmission line has a resistance of 0.22 ohm and inductive reactance of 0.36 ohm.…

A: Write the given values. R=0.22 ΩXL=0.36 ΩSR=500 kVAVR=2000 Vpf=0.707 lagging

Q: The RL (Resistive and Inductive) Load in the Load Side Section of the Transmission Line Simulator is…

A: For loading, generally resistor and inductor are connected in series.

Q: A lossless transmission line has a capacitance per unit length of 64pF/m and an inductance per unit…

Q: (b) A 3-phase transmission line has a resistance per phase of 50 and an inductive reactance of 150…

A: Given 3-phase transmission line Resistance per phase R=5 ΩInductive reactance per phase XL=15…

Q: km, and C=8.86nF/km. At full load, the line delivers 250MW at 0.9 pf lagging and 230 kV. Using the z…

A: All the values of R,L and C are given in per unit length. We will multiply them with total length…

Q: 3.) Identical series capacitors are installed in each phase at both ends of the line in #1 and…

A: Series compensation is used to improve the power transmitted through transmission lines. it…

Q: A load of 1000 kW at 0·8 p.f. lagging is received at the end of a 3-phase line 20 km long. The…

Q: Vs 3Ω j4 N Vc 3Ω j4 N VR Is Ic IR 80 Ω j 5-106 siemens j60 N

A: Given that the receiving end end voltage is 154 kV. Therefore, the two port network parameters A and…

Q: The voltage regulation of a short transmission line is estimated: O a. Only on Line Inductance O b.…

A: At the point when a transmission line is conveying current, there is a voltage drop in the line…

Q: power of 90+j70 MVA is drawn from the end of a 220 km three-phase transmission line with a voltage…

Q: 2. A balanced load of 30 MW is supplied at 132 kV, 50 Hz and 0-85 p.f. lagging by means of a…

A: As per our guidelines we are supposed to answer only one question. Kindly repost other questions as…

Q: A load of 120 MW at a power factor of 0.6 lagging can be delivered by a 3-phase transmission line.…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: Using a test equipment, Vmax was found to be 5V while Vmin is 1V. The distance between voltage…

A: Given : Note : Please note that for the proper understanding here we have used two methods to…

Q: P 8.5 A single circuit three phase 220kV line runs at no load. Voltage at the receiving end of the…

Q: A short three phase transmission line of parameters R-0.4Ω and X=0.4Ω is delivering 2000kVA to a…

A: The transmission line performance can be determined by using four parameters namely series…

Q: Question 4 If the phase parameters for this 50HZ, 40km transmission line are R=20, L=10mH, and…

A: R= 2 ohms L = 10 mH and C = 8000 μF, f = 50 Hz XL = 2πfL = 2 x 3.14 x 50 x 10 x 10 -3 = 3.14j ohms…

Q: Three-phase transmission line has ABCD constants as shown below. The line is 80 km long. A =…

A: The transmission line problem can be solved easily.

Concept explainers

Distribution System

The final stage in the delivery of the electric power is the electric power distribution system. From the transmission system to the individual customers it carries electricity. The distribution system is connected with the transmission system and is used to lower the voltage of the transmission to medium voltage in the range of 2 kV to 35 kV with the help of transformers. This medium voltage to the distribution transformers located near the customer's premises is carried by the primary distribution system lines. These distribution transformers in turn lower the voltage to utilization voltage used in lightings, household appliances, industrial equipments etc. Through secondary distribution lines often several customers are supplied from one transformer. It is through service drops, the commercial and residential customers are connected to the secondary distribution system lines. Customers who demand a larger amount of power can be connected directly to the primary distribution system level or the sub-transmission level.

Question

100%

For a given short transmission line of impedance R+jX ohms/phase, the sending
end and receiving end voltages Vs and Vr are fixed. Derive the expression for the
maximum power that can be transmitted over the line.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 40-km, 220-kV, 60-Hz, three-phase overhead transmission line has a per-phase resistance of 0.15/km, a per-phase inductance of 1.3263 mH/km, and negligible shunt capacitance. Using the short line model, find the sending-end voltage, voltage regulation, sending-end power, and transmission line efficiency when the line is supplying a three-phase load of (a) 381 MVA at 0.8 power factor lagging and at 220 kV and (b) 381 MVA at 0.8 power factor leading and at 220 kV.
A small manufacturing plant is located 2 km down a transmission line, which has a series reactance of 0.5/km. The line resistance is negligible. The line voltage at the plant is 4800V(rms). and the plant consumes 120kW at 0.85 power factor lagging. Determine the voltage and power factor at the sending end of the transmission line by using (a) a complex power approach and (b) a circuit analysis approach.
A short three phase transmission line of parameters R-0.4Ω and X=0.4Ω is delivering 2000kVA to a load at a pf of 0.8 lagging at the receiving enf=d of the line.if the load voltage is 3000 V, determine the voltage regulation and efficiency of the line.
(Q) A 10 mile transmission line with an impedance of (0.122+j0.849) Ω per mile is delivering 230A at 230kV and 0.8 power factor lagging. Determine: the sending end voltage the line efficiency and regulation
transmission line with an impedance of 35 Ω is connected to a load of impedance of 300 Ω, then the value of VSWR assuming that the line impedance is decreased by 30 % and load impedance is increased by 40%.
A short 3 phase transmission line, connected to a 33kV, 50 Hz generating station at the sending end is required to supply a load of 10Megawatts at 0.8 power factor lagging, 30kV at the receiving end. If the minimum transmission line efficiency is to be limited to 96%, estimate the per phase values of resistance and inductance of the line.
Give the physical significance of the generalized circuit constant A,B,C and D of a transmission line. Find the values of A, B, C, D in the following approximate methods in terms of Z and Y (i)simple series impedance method (ii) nominal π method (iii) nominal T method
A 50ohm transmission line powered by a 3GHz source and terminated with a load impedance ZL=25-j60 ohms will be matched with the shorted parallel side. What should be the length, in m, of the parallel lateral line calculated using the Smith diagram ?
A short 3-phase transmission line connected to a 33kV, 50 Hz generating station at the sending end is required to supply a load of 10 MW at 0.8 lagging power factor at 30 kV at the receiving end. If the minimum transmission efficiency is to be limited to 96%, estimate the per phase value of resistance and inductance of the line.
Question-2) The parameters of a three-phase transmission line are given as Z = (12.84 + j72, 76)Ω and y = j5, 83x10^-4 mho. At the end of the line, a power of 55 MVA with a power factor of 0.8 is drawn under 132 kV voltage. Accordingly, calculate the line head voltage, active and reactive power values per line, and voltage regulation of the line using the nominal π circuit.7-) Since 55 MVA power is drawn from the end of the line under the conditions mentioned above, calculate the line head voltage (phase-phase voltage) and enter it in the box below. (The value will be entered in kiloVolts. Only the amplitude value of the voltage will be entered. The phase value will NOT be entered!!! Two digits after the comma will be sufficient. )8-) Since 55 MVA power is drawn from the end of the line under the conditions mentioned above, calculate the active power value per line and enter it in the box below. (The value will be entered in MegaWatt. It will be sufficient to take two digits after…
A load impedance of 30<70° fl ohm connected to a 50-oh line Vs is determined as 6 V, andthis is used as the reference voltage. Given that the line is lossless andLamda/4 long, calculate (a) Vm (b) VRs, (c) V1L, and (d) VRL
Calculate the impedance looking into a 50 Ω line 1 m long, terminated in a load impedance of 100 Ω, if the line has velocity factor of 0.8 and operates at a frequency of 30 MHz.