Hello Sir.Good NightI have a question related Machine Vibration Lesson. The following below is my question.Please advise, Thank you so much. C2/3 €+cgXe/3|J=1/12 ml²for example is a bridge that is supported on the left by a spring and damping while the rightis only supported by a spring, determine :1. Free body diagram of the system2. What is the personal frequency3. Determine the shape mode that occurs

Given:To find:Free body diagramNatural frequencyMode shape

Answered: for example is a bridge that is…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 0.600kg mass oscillates at the end of spring that has a spring constant of 300N/m. the initial amplitude is 0.500m . the damping force is proportional to the velocity, -av. If the amplitude decreases from .50m to 350m in 2.50s . What is the damping constant ?Is the system underdamped, critically damped or overdamped?
A 0.600kg mass oscillates at the end of spring that has a spring constant of 300N/m. theinitial amplitude is 0.500m . the damping force is proportional to the velocity, -av. If theamplitude decreases from .50m to 350m in 2.50s . What is the damping constant ?Is thesystem underdamped, critically damped or overdamped?
A 35 K G block is connected to a support through a spring (k=1.4 * 10^6 N/m) and a damper (c=1.8 * 10^3). The support is given a harmonic displacement of 10 mm at a frequency of 35 Hz. What is the steady state amplitude of the block?
1_What value of w results in steady state oscillation with maximum amplitude Under this condition? 2- The value of the quality factor is equal to 3_Damping type. 4_What is the maximum amplitude 5_The phase shift is about
One of the tail rotor blades of a helicopter was damaged, and due to the repair, there is an extra 2 kg mass 0.40 m from the axis of rotation. The equivalent system before the repair had a mass of 102 kg and stiffness of 93.8 kN/m. Assume the rotor was well-balanced before the damage. The repaired helicopter tail has a damping ratio of 0.15. Find the steady-state response of the tail when the blades rotate at 1500 rpm.
It is observed from the magnitude plot of a compliance transfer function of a mass spring damper that the value at a very small frequency 0.0001 is 3.71 meters and at resonance 1.10 rad/s is 7.10 meters. What is the natural frequency, damping coefficient, stiffness, and mass of the system?
A two degree of freedom damped system has natural frequencies 2 rad/s and 3 rad/s and corresponding mode shapes {21}{ 2 1 } and {1−1}{ 1 − 1 } . A damping ratio of 2% is assumed for both modes. The initial displacement is {10}{ 1 0 }mm and initial velocity is {21}{ 2 1 }mm/s. The displacement of the first degree of freedom in mm at time t=3 s is
1. Determine the driven response for: Bi k B2 k mi m2 Given: ID k spring constant, mě – mass, B: - damping coefficient, F(t) Initial data: ID = 500351 ID % 4 = 1
Vibrations Question It is observed from the magnitude plot of a compliance transfer function of a mass spring damper that the value at a very small frequency 0.0001 is 3.71 meters and at resonance 1.10 rad/s is 7.10 meters. What is the natural frequency, damping coefficient, stiffness, and mass of the system?
The equation of motion of a certain mass-spring-damper system is 5x'' + cx' +10x = f(t). How large must the damping constant c be so that the maximum steady-state amplitude of x is no greater than 3, if the input is f(t) = 22sin(wt), for an arbitrary value of w?
(b) Consider a vertical spring mass-damper-system with mass m = 2 kg, damping coefficient c = 5 N.s/m and stiffness k = 10 N/m. An external force f(t) = sin3t N is applied to the mass. (i) Find the static equilibrium position as measured from the un-stretched length of the spring (ii) Write the equation of motion. (iii) Find the natural and damped frequencies. (iv) In steady state, find the time delay in seconds between the mass position and f(t). (v) Find the steady state maximum acceleration.
An industrial sewing machine of 65 kg has an unbalance value of 0.15 kgm per rotation. The machine operates at 125 Hz and is located on the ground with a spring coefficient of 2 x 106N / m and a dimensionless damping coefficient of 0.12. Find the uniform regime amplitude of the machine.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

for example is a bridge that is supported on the left by a spring and damping while the right is only supported by a spring, determine : 1. Free body diagram of the system 2. What is the personal frequency 3. Determine the shape mode that occurs