for part a , b c only f= 250p=270x= 6a= 55A wooden beam is fixed at A. Four cables with forces "P" and "F" act on the beam as shown.a. Draw the free body diagram of the wooden beam.b. Determine the resultant force (FR) in Cartesian vector form.c. Determine the magnitude and direction angles 8,, 6y, and 0, of the resultant force (FR).d. Determine the horizontal and vertical components of the reactions at A.e. Determine the Moment at A.-2 ft-FBr2 ftFPX2 ft

Answered: Image /qna-images/answer/3b2ed12c-2f2c-46bc-bff7-aac5091a60ad.jpg

Answered: for part a , b c only

Engineering

Mechanical Engineering

for part a , b c only

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.6P: Find the internal force systems acting on sections 1 and 2.

See similar textbooks

Similar questions

An L-shaped bracket is supported by a frictionless pin at A and a cable between points B and D. If pin A is the origin, point C is at (-7, 0); and pin B is at (-7, -10). The cable is attached between point B and an anchor at point D, at (-2, -14). Units are in feet. Force F acts at point C at an angle of 60o from the positive x-axis. Determine the magnitude of the moment that the force F produces about point A. Determine the tension required to hold the bracket in position.
In the given figure below, a tube was supported at A and E by with a ball and socket and a wire at D connected to F. Determine the following given the Force F is equal to 656.46 N. X_b : 218.078 mm X_c : 451.531 mm Y_a : 215.719 mm Z_e : 163.433 mm Z_f : 463.933 mm 1. Determine the x, y and z-component of Vector DF 2. Determine the moment experienced by the system assuming that there is no wire support 3. Determine the x, y and z-component of the moment experienced by the system assuming that there is no wire support 4. Determine the Tension experienced by wire DF 5. Determine the x, y and z-component of the Tension experienced by wire DF.
In the assembly shown, member AB is rigidly attached to the wall while an L bar is pinned to AB at E. Two forces P and Q are acting on the assembly as shown. Force P lies on the x-axis while force Q is applied at point D along a plane parallel to the yz plane. 1. Which of the following quantities is/are zero? (Choices: A. Moment of P about the x-axis ; B. Moment of P about the y-axis ; C. Moment of P about the z-axis) 2. Which of the following best approximates the moment of force Q about point A? 3. Which of the following best approximates the equivalent force-couple set at point A of the applied forces P and Q? Note: F is the resultant force and Cis the resultant couple4. Considering the force diagram of member DE, which gives the complete set of reactions for the support at E? (Note difference of Force and couple reactions)
In the given figure below was supported at A and E by with a ball and socket and a wire at D connected to F. Determine the following given that force is equal to 687.4N: Determine the X-component of Vector DF Determine the Y-component of vector Df Determine the z- component of Vector Df Determine the moment experienced by the system assuming that there is no wire support. determine the x-component of the moment experienced by the system assuming there is no wire support Determine the y component of the moment experienced by the system assuming that there is no wire support Determine the z component of the moment experienced by the system assuming that there is no wire support determine the tension experienced by wire Df Determine the x component of the tension experienced by wire DF determine the y component of the tension experienced by wire DF Determine the z component of the tension experienced by wire DF Xb: 171. 995 xC : 477.445 Ya:200.266 ZE : 150.166 Zf : 492.252
In the given figure below, a tube was supported at A and E with a ball and socket and a wire at D connected to F. Determine the following give that Force F is equal to 690.86 N. Note: Express your answer in terms of the units. Observe 3 decimal places. 1.) Determine x-component of vector DF. 2.) Determine the y-component of Vector DF 3.) Determine the z-component of Vector DF. 4.) Determine the moment experienced by the system assuming that there is no wire support.
A force F1= 2i – 6k {kN) is applied at the position 3j + 5k {m}, meanwhile another force F2 = - i + 4j + 7k {kN) is applied at the position 8k {m}, on a structure. Evaluate the resultant moment by vector calculation
What are the magnitude (F) and the location measured from end A (d) of the equivalent resultant dorce of the triangular distributed load in the figure below.
Find the values of P and F so that the four forces shown in the figure will produce an upward resultant of 300lbs acting 4ft from the left end of the bar?
Please reply as soon as possible, static problem Determine the forces and internal moment at points 1 and 3 indicated in the figure. Consider the pins at A, B, and C. Points 1 and 2 are located just above and below pin C.
A tower shown in the figure above is powered by AB and AC cables. A worker of the tower A 12m long rigid rope ties to point A (| AE | = 12m) and applies a constant force of 120N to the rope. The angle between the tower and the AE rope is 30 °. The pull of cables and rope applied to point A Knowing that the sum (combination) of the forces is in the downward direction (along the y-axis) (point O is the origin); 1) type the until vector of the force on the AE rope in θ. 2) if the checks on the AB and AC cable required to be equal, what should be the angle ? 3) if the pull force on the AB cable desired to be maximum, 0 < θ < 180 angel calculate. 4) θ = 30 + 9x4= 66 a) find the severity of the force on the AB cable (TAB) b) find the severity of the force on the AC cable (TAC).
2. A ladder 12 m long leans against a vertical frictionless wall with its lower end 3 m from the wall. The ladder weighs 40 N. Find the magnitude and direction of the force exerted on the lower end of the ladder. 3. A uniform 25 N beam 6 m long is carried by two men A and B, one at each end of the beam. a) If A exerts a force of 20 N, where must a load of 45 N be placed on the beam? b) What force does B exert?
Three guy wires used in support system for television transmission tower that is 600 m tall. Wires A and B have tension as 60 kN whereas wire C has 30 kN as tension. What is the moment of wire forces about the base of the tower.