Question

I can't find i(o+)

For the circuit below, find:
(a) v(0+)
(b) i(0+)
(c) v(2ms)
1 = 0
500 Q
500 Q
-1 µF
2 kQ
50 V
i
(A) v(0+) = 40
(B) i(0+) =
mA
(C) v(2ms) = 17.96
Expand
Transcribed Image Text

For the circuit below, find: (a) v(0+) (b) i(0+) (c) v(2ms) 1 = 0 500 Q 500 Q -1 µF 2 kQ 50 V i (A) v(0+) = 40 (B) i(0+) = mA (C) v(2ms) = 17.96

Expert Answer

Want to see the step-by-step answer?

Check out a sample Q&A here.

Want to see this answer and more?

Experts are waiting 24/7 to provide step-by-step solutions in as fast as 30 minutes!*

*Response times may vary by subject and question complexity. Median response time is 34 minutes for paid subscribers and may be longer for promotional offers.
Tagged in
Engineering
Electrical Engineering

Related Electrical Engineering Q&A

Find answers to questions asked by students like you.

Q: What will be the time varying current i(t) flowing through a 10 mF capacitor if the time varying vol...

A: If v(t) V is the time varying voltage applied across a parallel plate capacitor of capacitance C F, ...

Q: The diode shown in the given diagram has 0.5 V voltage drop across it at all conditions and currents...

A: The voltage across the diode is given as 0.5-V at all conditions.Redrawing the circuit by marking cu...

Q: Determine the signal to quantization noise ratio for a 6 bit PCM.

A: Quantization Noise: The sampled signal with quantization error is the decoder output in a PCM receiv...

Q: Find |V2| , 82, and Sgifor the system shown in Pig 1. .In the transmission system all the shunt elem...

A: Calculate the shunt admittance,

Q: Please design a cyclic shift right register with D flip flops

A: In cyclic shift register the shift out is fed back to the shift-in. It is basically the cascade conn...

Q: I'm having trouble with this one. (P.S. this is an old exam, where I didn't answer the question and ...

A: Use Kirchhoff’s current law at node x in the circuit.

Q: Solve for V1 and V2 show step by step

A: Given equations are

Q: 2. Investigate the stability of GH(s)- of Ti and T2 K(1+T,) using Nyquist Stability Criteria for pos...

A: The given transfer function can be expressed as:-

Q: Find V in the circuit shown in Figure P272. 2.72 FIGURE P2.72 R, 4 kn 2 kl) R. Re 2 kfl 3 k2 R. Rg 2...

A: Given modified circuit is shown below.

Q: 10. Sketch the root locus and find the range of K for stability for the unity-feedback system shown ...

A: Steps to sketch the root locus:Root locus always starts from open loop pole and ends at zero of the ...

Q: The clock select register for channel A in an MC68681 DUART has bits 0 through 3 set to 0, 0, 0, and...

A: For the bits in clock register of the 0, 0, 0, 1 signal, the baud rate will be 2400.

Q: Please help!

A: The labeled circuit diagram is given as

Q: An analog signal having a maximum frequency of 10 kHz is being transmitted through a PCM system with...

A: If the maximum frequency component present in the analog signal if fm Hz, then the minimum transmiss...

Q: Intermittent wiper delay interval on late models vehicles is controlled by the BCM.  True or False

A: The intermittent wiper switch system is shown below:

Q: From your understanding, what is the differnece between a grounding wire and a grounded wire? I answ...

A: The name grounding and grounded are very similar to each other, which arises confusion in understand...

Q: Write down and explain Shockley equation for drain current for JFET.

A: The Shockley’s equation involving drain current ID for a Junction Field Effect Transistor (JFET) can...

Q: For a silicon pn junction under forward biased condition, the reverse saturation current is 10 nA. I...

A: Using Shockley’s equation, the value of the current flowing through a p-n junction diode can be expr...

Q: Find Fourier transform of x(t) and inverse Fourier transform of X(ω).

A: We’ll answer the first question since we answer only one question at a time. Please submit a new que...

Q: Given the following State Diagram, write the equations for the D-Flipflop A,D-Flipflop B, and Output...

A: Truth table for the given diagram:

Q: A transmission line has a characteristic impedance of 100 ohm and a resistance of 0.2 ohm/m. If the ...

A: A transmission line can be characterized by 4 parameters:1. Resistance per unit length (R)2. Conduct...

Q: blank sheets of BODE paper and, using straight line approximations,hand draw the Gain and Phase (Bod...

A: Calculate the gain of the system.

Q: Exercise: In Figure 4 the two-terminal network of Figure 3 with the parameters of Table 3 is placed ...

A: Redrawing the given circuit diagram, using the given points:

Q: The open circuit and short circuit impedance of a transmission line are 200 ohm and 50 ohm respectiv...

A: Given data:

Q: Problem 2: Provide a circuit inside the box such that there's maximum power transfer at f-1MHZ. LI=L...

A: Let the impedance of the box be ZL and redraw the circuit by short-circuiting the voltage source as ...

Q: The capacitance per unit length and the characteristic impedance of a lossless Transmission line are...

A: It is given that, the capacitance per unit length and the characteristic impedance of a lossless Tra...

Q: The Type K thermocouple has a sensitivity of about 41 micro-Volts/℃, i.e. for each degree difference...

A: The resolution of the 16 bit ADC is

Q: Explain briefly, why the form 3 Т. 2 xi LL 11 e of the torque equation is beneficial considering ind...

A: Given torque equation of induction motor –

Q: Figure 4, sketch the root locus as a is vatied. (Run a numerical simulation and verify your solution...

A: It is the case when the poles are varying other than the gain K. To draw the root locus, rewrite the...

Q: the question is have is  solve z1/z2 in polar form.  z1= 3-j2 and z2=-4+j2.  i solved that z1 polar ...

A: Dear student you are absolutely correct also the expression from the calc is also correct.  The give...

Q: From the following differential, find out the corresponding transfer function:

A: Transfer function is defined as the ratio of the Laplace transform of the output to the Laplace tran...

Q: Hi, for electric circuits with both current and voltage sources present what is the fastest way to d...

A: Hello,The fastest way to do the analysis with both current and voltage sources present,  depends on ...

Q: Find out the Laplace transform of the function x(t)=5u(t-10) where u(t) is the unit step function.

A: Write the expression for the Laplace transform,

Q: An opamp inverting amplifier has a gain of -1000 and the value of the input offset voltage is 1 mV. ...

A: Op-amp has two input terminals: the inverting input terminal and the non-inverting input terminal. T...

Q: What will be the maximum value of x until which sin x =x holds within 10% error range?

A: Using the series expansion formula, sin x can be expanded in a series form as

Q: Find inverse Z transform using partial fraction expansion: X(Z)=4Z2/(Z-3)(z+5), RoC: |Z|>3.

A: Inverse Z transform is used to convert a function from discrete frequency (Z) domain into discrete t...

Q: 4. Z-Transform: Consider the following three discrete-time LTI systems: 1 1 H1(2) 1 H2(2) H3(2) = 1 ...

A: Given discrete-time LTI systems are

Q: Two 3V batteries are connected in parallel to a 10 ohm resistor, where one of the batteries has doub...

A: Drawing the circuit diagram for the given points.The internal resistance of the battery is connected...

Q: For sinusoidal modulation in an AM system, what will be the value of the modulation index when the m...

A: For an amplitude modulated system under sinusoidal modulation, the modulation index (m) can be evalu...

Q: In an ungrounded electrical systems with conductors installed in grounded metal raceways and enclosu...

A: In an ungrounded system, the system has no direct connection with the grounding electrode. When the ...

Q: For an operation amplifier, the differential gain and the common mode gain are 105 and 102 respectiv...

A: Click to see the answer

Q: The propagation constant associated with a plane wave is (0.1 pi + j 0.2 pi)/m. What will be the wav...

A: For a plane propagating wave, the propagation constant can be expressed as

Q: Find and sketch both v and i in the circuit shown below for a period slightly before t = 0 until ste...

A: For t<0, the capacitor is open circuit and a steady-state circuit will be as follows.

Q: _______ connectors are intended for use only with cable employing corrugated copper tube.    A. Alum...

A: The connectors are selected depending on the size and types of cable. Connectors are designated acco...

Q: An analog voltage in the range 0 to 8 V is divided in 16 equal intervalsfor conversion to 4-bit digi...

A: Quantizer is essential to convert an analog signal into a digital signal. After the analog signal is...

Q: Please answer  17,18,19 & 20

A: (17)  Micro-stepping is used to move the stepper motor smoothly. In order to move the stepper motor ...

Q: hand solution and Matlab. if its possible can any one post a command list for matlab for control?

A: PART a: Given overshoot is 0.1 Write the expression for the peak overshoot, 

Q: Find vo(t) a) Using convolution integral 4 ww ร 45 2

A: As given in the question

Q: Hi, is my answer accurate?

A: The given Fourier transform can be found out using the property of shifting in Fourier transform.