For water flowing in a pipe of 8 inches diameter at 65 oC and 0.01 ft3/s, what will be the entry length (Le) needed for water flow to be described as fully developed flow? What does that tell you about the length of the tube you should select in your design?

For water flowing in a pipe of 8 inches diameter at 65 oC and 0.01 ft3/s, what will be the entry length (Le) needed for water flow to be described as fully developed flow? What does that tell you about the length of the tube you should select in your design?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.4P: 5.4 Evaluate the Stanton number for flow over a tube from the following data: , , , , .

See similar textbooks

Related questions

Q: Determine the average velocity for water flow in a 2 in diameter pipe, Schedule 40 chlorinated…

A: Given data, Schedule 40 chlorinated polyvinyl chloride pipe D = outside diameter = 2.375 in d =…

Q: Water at 20°C flows steadily through the piping junction in Fig. P3.32, entering section 1 at 20…

A: Given data: Consider the diagram shown below for the different sections taken,

Q: A horizontal pipe, originally smooth but due to constant use, was found to be scaling through…

Q: 5. Water at 50C flows in a 150-mm diameter pipe with a velocity of 6.5 m/s. The surface roughness of…

Q: Castor oil flows through 100 m of 4-nominal, schedule 40 cast-iron pipe. Determine the pressure drop…

Q: Determine the size of clean wrought-iron pipe (e=0.046 mm) required to convey 250 L/s of oil,…

Q: The parabolic velocity profile in a fully developed laminar flow in a pipe is given by the following…

A: Given: The velocity profile in a fully developed laminar flow is given as : u(r)=-R24μdPdx1-r2R2

Q: oF 10 Hot water at 80°C is flowing to a dishwasher at a rate of a 15.0 1/min through a standard…

Q: A pond located at 60 m height is requiring a pump to deliver water at a capacity of 0.05 m³/s from…

A: The losses which becomes 0.95 part of total head loss through pipe flow is termed as major losses.…

Q: Examples: Example 1: Water (p= 62.36 lbm/ft° and µ= 7.536×10* lbm/ft-s) is flowing steadily in a 2…

A: Given, Density , ρ = 62.36 lbm/ft3 Viscosity , μ= 7.536*10-4 lbm/ft.s Diameter of the pipe , D =2…

Q: Determine the Reynold's Number and flow regime of an bil flowing through a 450-mm diameter pipe, if…

Q: A piping system involves two pipes of different diameters (but of identical length, material, and…

A: There are two different types of pipes and have different diameters and the same length, the same…

Q: A long 1.5 km pipeline with size of 300 mm laid between two reservouirs having difference in surface…

A: From the Darcy Weisbach equation hf=fLQ212.1 d5

Q: A cast iron pipe of equilateral triangular cross sectión with side length of 20.75" has water…

A: Given Data : Sides of equilateral triangle = 20.75 inch Flowrate = 6000 gallon per minute…

Q: a) Determine the radial positions of a pitot tube for a 6-point traverse in a 0.3 m inner diameter…

A: Solution: Given Data: D=0.3 m Note: Dear User! As per our guidelines, we are only allowed to…

Q: (Hardy Cross Method (2 iterations) and EPANET) For the same system, determine the pressures and…

A: applying the bernoullis equation we get P1ρg+V122g+z1=P2ρg+V222g+z20.8 x 14462.4 x 39.17+d22 x…

Q: Q.Y water is trans por (1.5)in - dianeker wroughtiron horizontal pipe with flow rate of (01 H/9).…

Q: A 30-cm by 15-cm Venturi meter is mounted on a vertical pipe with the flow upward. One hundred…

Q: 14–2C Consider laminar flow in a circular pipe. Is the wall shear stress T,, higher near the inlet…

Q: 1. Given that the transition Reynold's number for flow in a duct is 2300, the smallest pipe for…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: For oil (SG = 0.86. u = 0.025 N-s/m? ) flow of 0.24 m/s through a round pipe with diameter of 521…

Q: For a commercial steel pipe, the value of the Resistance Coefficient = 0.25 and the Flow Rate = 3.3…

Q: 9.42. In an established flow in a pipe of 0.3 m diameter the centerline velocity is 3.05 m/s and the…

A: Given: d = 0.3 m u=2.73 m/s u=3.05 m/s y= 75 mm = 0.075 m

Q: Q2) For laminar flow conditions. Calculate the pipe diameter should be installed to carry 0.022m/s…

A: Given, Flow rate , Q = 0.022 m3/s Kinematic viscosity of oil , v = 0.00021m2/s Specific gravity =…

Q: 8.20 For a turbulent flow of a fluid in 0.6 m diameter pipe, the velocity 0.15 m from the wall is…

Q: 3. A 100 m length of smooth horizontal pipe is attached to a large reservoir. What depth d, must be…

Q: Use Poiseuille's Law to select the diameter of a 10-m long plastic pipe that is to transport room…

A: Given Properties of water at room temperature

Q: Derive the relation (Hagen-Poiseulle Law) for the head loss due to friction in Laminar flow case in…

Q: lost in (30m) of this pipe is measured experimentally and found to be (533m). Calcne Water flow in…

Q: Water at 59 F flows through a straight section of a 6-in-ID cast-iron pipe with an average velocity…

Q: Water flows down an inclined tapered pipe 45 m long at a slope of 1:10. The areas at upper and lower…

A: GIVEN DATA- TAPER PIPE WITH SLOPE 1:10 PRESSURE AT UPPER END =100KPa AREA 8m2 AND 3m2 VELOCITY AT…

Q: What is the Reynolds number for a straight and perfectly smooth pipe of length 500 m and diameter…

A: Consider Q is the mass flow rate, ρ is the density of fluid, V is the velocity of the fluid and A is…

Q: Using the Moody diagram above, estimate the friction factor for a pipe flow with Reynolds number 2…

Q: ump has the following characteristic: Volume flow rate (m³/h) Head (m) 23 46 69 92 115 17 16 13.5…

A: A curve is plotted using the above data sets. Since we have two reservoirs and there is a difference…

Q: A 0.5-inch diameter water pipe is 18 m long and delivers 19 L/min. What fraction of this pipe is…

A: Given: Diameter of the pipe (D)=0.5in or 0.0127m Flowrate Q=19L/min Length of the pipe (L)=18m

Q: determine total head loss of the system and gauge pressure p2 in order to deliver water at 2…

A: For solution refer below images.

Q: Three cast iron pipes are laid in parallel with thesedimensions: The total flow rate is 200 m3/h of…

A: The flow rate of water is Q=200 m3/h. The temperature is T=20°C. The length of pipe 1 is L1=800 m.…

Q: Determine the Reynolds number for a flow of 25 ° C water in a 2 in diameter sanitary pipe at a rate…

A: Givenm˙=0.15kg/sv=m˙ρA=0.151000×π4D2=0.076m/sρwater=1000 kg/m3μwater=8.9×10-4 PaD=2 in=0.05…

Q: Water with a dynamic viscosity of 0.892 cP flows in a smooth pipe of diameter, D = 50 mm and length,…

A: Given, μ=0.892 cP=0.892×10-3 Pa.sD=50 mm=0.05 mL=10 mvm=1.5 m/s Let the density of the water be…

Q: Explain how flow rate is measured with a Pitot-static tube, and discuss its advantages and…

A: A pitot tube is a simple round cylinder with one end opened with a small hole and the other…

Q: In a commercial steel pipe of diameter 0.01906 (in meters), industrial waste water (approximate as…

A: Given Data: The diameter of the pipe is, D=0.01906 m. The average velocity of water is, V=30 m/s.

Q: 1 Kerosene (20°C) flows at a rate of 0.04 m3 s in a 25 cm diameter pipe. Would you expect the flow…

A: GivenDiameter of the pipe =25 cmQ=0.04 m3

Q: Water flows at 7.2 m'/h through the depicted horizontal diffuser which gradually enlarges from a d,-…

Q: e diameter of an open-topped tank 1.5 m high increases uniformly from 4.2 m at th se to 6 m at the…

A: As per guidelines we need to answer only first question

Q: Question 9 The Nusselt number for fully developed laminar flow in a pipe first increases and then…

A: The Nusselt number for fully developed laminar flow in a pipe is a fixed number and remains constant…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the Reynolds number for a straight and perfectly smooth pipe of length 500 m and diameter 0.2 m, transporting oil (density 900 kg/m3 and viscosity 0.5 Pa-s) at a flow rate of 100 kg/s from sea level to an elevated height 10 m above sea level? What is the viscous pressure drop along the pipe?
Considering pipe loss only, how much head is required to deliver 0.222 m³/s of heavy fuel oil at 38°C through 914 m of new cast iron pipe, 300 mm inside diameter? Use ε=0.00024 m. (ANSWER MUST BE = 41 m)
I6 a) Determine the radial positions of a pitot tube for a 6-point traverse in a 0.3 m inner diameter pipe. Show your calculations. b) If the fluid velocity measured at the pipe center is 0.3 m/s and yields a Reynolds number based on local velocity of 4000, what is the fluid cross-sectional average velocity in the pipe? c) At what value of Re is the discharge coefficient of an orifice meter approximately independent of geometry and flow rate?
Water at 75°C 3.83 x10-7m²&9.56 kN) (v= is Sm3. flowing in a standard hydraulic copper tube, 13.4mm diameter, at a rate of 12.9 L/min.Calculate the pressure difference between two points 45mapart if the tube is horizontal with friction factor 0.0205.
Water flows in a 3.5-cm-diameter pipe so that the Reynolds number based on diameter is 2000 (laminar flow is assumed). The average bulk temperature is 10°C. Calculate the maximum water velocity in the tube in m/s. (Recall that um = 0.5ug)
A horizontal pipe, originally smooth but due to constant use, was found to be scaling through corrosion where the effective surface roughness rises. This resulted for the fanning friction factor to be twice the original value. Determine the percent increase in the pipe diameter if the volumetric flowrate and pressure difference remains the same when it was new and old. Blank 1 %
Determine the average velocity for water flow in a 2 in diameter pipe, Schedule 40 chlorinated polyvinyl chloride (CPVC) pipe (2.375 in outside diameter and 2.047 in inside diameter) carrying cold water at a volumetric flow rate of 40 gpm.
Determine the size of clean wrought-iron pipe (e=0.046 mm) required to convey 250 L/s of oil, =1x10-5 m2 /s), 3000 m long with a head loss of 25 m.N/N. [ Hint: Use Colebrook equation for transitionally rough pipe (whatever is the calculated f, that is final and no need to check if the pipe is smooth or rough).
Explain how flow rate is measured with a Pitot-static tube, and discuss its advantages and disadvantages with respect to cost, pressure drop, reliability, and accuracy.
In cases that there is a desired flowrate, what design considerations must be specified in the piping system if the mechanical energy losses are to be minimum? Explain briefly.
A 1/4” inside diameter pipe is used to transport SAE 30 motor oil (µ = 0.006266 slug/ft-s and ρ =1.7267 slug/ft3) over a distance of 100 ft. Assuming that the pipe is horizontal and the flow throughit is steady, laminar, and fully-developed, what gauge pressure must a pump develop at the head ofthe pipe to provide a flow rate of sufficient to fill a quart bottle every 5 seconds? [6291 psi] Whatis the Reynolds number (based on diameter) for this flow? [112.5] Is the assumption of laminar flowreasonable?
If the two pipes in Fig. are instead laid in serieswith the same total pressure drop of 3 lbf/in2, what will theflow rate be? The fluid is SAE 10 oil at 20°C.