Q 5 The compressor of a simple open cycle gas turbine plant raises the temperature of the airfrom 21°C to 150°C. The gases leave the combustion chamber at 680°C when the flow ofthe fuel used is 4.5 kg/min with a calorific value of 44 MJ/kg. find:Pressure ratio of the plant.b. Turbine exhaust temperature.a.C. Turbine power output.d. Power absorbed by the compressr.Cycle thermal efficiency.С.

Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Answered: from the fu

Engineering

Mechanical Engineering

from the fu

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A generator uses a gas turbine cycle. Air enters the compressor at a pressure of 1 bar and a temperature of 30°C with a compressor efficiency of 0.85. Hot gas exits the combustion chamber at a pressure of 9 bar and a temperature of 900°C. The power generated by the turbine is 2400 kW with a turbine efficiency of 0.82. a. Draw installation diagrams and T-s cycle process diagramd b. Determine the work of the compressor and turbine and the mass rate of the air requirement c. Cycle thermal efficiency (air: Cp=1,005 kJ/kg. K dan γ=1.4; Gas hot: cp=1,005 kJ/kg K and γ=1.4)
A 150 MW gas turbine power plant running on Ideal Brayton cycle has the following initial conditions; air at 22°C & 95 kPa. The compression ratio is 7 and the temperature at the turbine is 910°C. Draw the P-V and T-S diagrams and determine the following: d. Thermal Efficiency e. Mass flow rate, kg/min
A turboprop aircraft propulsion engine operates where the air is at 8 psia and −10°F, on an aircraft flying at a speed of 600 ft/s. The Brayton cycle pressure ratio is 10, and the air temperature at the turbine inlet is 940°F. The propeller diameter is 10 ft and the mass flow rate through the propeller is 20 times that through the compressor. Determine the thrust force generated by this propulsion system. Assume ideal operation for all components and constant specific heats at room temperature.
Air enters the compressor of an ideal air-standard Brayton cycle at 110 kPa, 289 K, with a volumetric flow rate of 5 m3/s. The compressor pressure ratio is 12:1. The turbine inlet temperature is 1567 K. Take the gas constant as 289 J/kg.K and Specific heat at constant pressure and constant volume for air as 1.004 kJ/kg K and 0.708 kJ/kg K respectively. Calculate the net power developed to two decimal places and include the correct SI unit symbol.
2.) A 150 MW gas turbine power plant running on Ideal Brayton cycle has the following initial conditions; air at 22°C & 95 kPa. The compression ratio is 7 and the temperature at the turbine is 910°C. Draw the P-V and T-S diagrams and determine the following: a. Pressure, volume & temperature at each state b. Pressure ratio c. Heat Added, per unit mass
Air enters the compressor of an ideal air standard Brayton cycle at 100 kPa, 290 K, with a mass flow rate of 6 kg/s. The compressor pressure ratio is 10. The turbine inlet temperature is 1500 K. If a regenerator with an effectiveness of 70% is incorporated in the cycle, determine (i)turbine work, (ii) compressor work, (iii) heat supplied, and (iv) the efficiency of the cycle. Draw a suitable block diagram and T-s diagram. Take Cp=1.005 kJ/kg K and ϒ= 1.4
A turbojet aircraft moving with a velocity of 790 ft/s at a runway where the pressure& temperature is found to be 14.7psi & 546R. The axial flow compressor provides apressure ratio of 14 to 1. Temperature at the turbine inlet is 2000R. The mass flowrate of airinside the engine is 133 lbm/s. Determine the following:a. T-S diagramb. Pressure & temperature at each statec. Thrust force (lbf)d. Propulsive power developed (BTU/min)e. Propulsive Efficiency
Air enters the compressor of an ideal air-standard Brayton cycle at 100 kPa, 27 °C, with a volumetric flow rate of 5 m3/s. The compressor pressure ratio is 5. The turbine inlet temperature is 1127 °C. Assume cold-air analysis, determine the net power developed of the cycle. determine the thermal efficiency of the cycle. Determine the heat rejected to the condenser, in kW, determine the back work ratio. determine the input heat into combustor, in kW.
A 120 MW gas turbine power plant running on Ideal Brayton cycle has the followinginitial conditions; air at 22°C & 95 kPa. The compression ratio is 7 and the temperature atthe turbine entrance is 910°C. Determine the following: a. Pressure & temperature at each stateb. T-S diagramc. Heat Added, per unit mass
One kilogram of a perfect gas (air) is used as a working substance in a Carnot power cycle. At thebeginning of isentropic compression, the temperature is 326 o K and the absolute pressure is 359 kPa. Theabsolute pressure at the end of the isentropic compression is 1,373 kPa. For this cycle, the isothermalexpansion ratio (v 3 /v 2 ) is 2.0. For the cycle, calculate the heat supplied, kJ/kg.A., heat rejected, and the network
An ideal Diesel engine operates on 0.63 lbm of air with a suction state at 14 psia and 140 °F. The pressure at the end of compression is 458 psia and the volume at the end of heat addition process is 0.13 ft^3. Using air properties (R=53.34 ft-lbf/lbm-R, k=1.4, Cp =.24, Cv=.1714 Btu/lbm-R), determine compression ratio, percentage clearance, Qa, Qr, Thermal Efficiency, mean effective pressure. Plss Show complete solution with the corresponding unit cancellation. Thank you
A closed-cycle gas turbine plant consists of a compressor, a heat exchanger, a heater, a two-stage turbine with reheater, and a cooler. The maximum and minimum pressures and temperature in the cycle are 30 bar and 570oC, and 7.5 bar and 15oC. The pressure in the reheater is 15 bar. Sketch the layout of the plant and indicate pressures and temperaturesbetween the components if (a) the heat exchanger is used, (b) the heat exchanger by-passed.Calculate the ideal cycle efficiencies and work ratios in both cases. The gas used in the circuit is helium, which has a molar mass of 4 kg/kmol and cp=1.5 R