Give two reasons for using standard letter designations

Q: With neat diagram explain the construction and working principle of any one Mechanical Transducers.

A: A bimetallic thermometer is a contact type temperature measuring device which uses the principle of…

Q: Please help me with number 9,10 and 16. This is not graded.

A: 9. Length of threads=16.5 10. No. Of threads=20/2.5= 8 16. No. Of threads=20/1.5=13

Q: The shafts used for transmitting the power and torque are always supported using bearings. Select…

A:

Q: List at least three advantages that fluid power has over mechanical power.

A: These are the main three advantages of fluid power over mechanical power High horse power to weight…

Q: Explain Absolute programming and  Incremental programming.

A: Absolute coordinates in a CNC programming is a way to assign coordinate position to the tool. In…

Q: Which symbol indicates that a change has been made to a CPT guideline, and/or note when compared…

A: When a change is made to a drawing or a manual in engineering, codes, and symbols are used to…

Q: Write a short note on G codes and give any four examples with its application. (Reg. Number Ending…

A:

Q: Briefly describe what is meant by a right handed system of coordinate

A: System of cordinates -  A cordinate system is defined as a system which is used to define the…

Q: Reprogramming is not possible in CNC (Computer numerical control) systems. Select one: True False

A: Computer numerical control (CNC): The CNC programming is the process which is to create program…

Q: Complete the following table of Pneumatic Symbols.

A: Given Pneumatic Symbols To find Fill the table

Q: 2. It is used to loosen or tighten screws that have a star-like depression on the top, a feature…

A: Since you have posted a multiple independent questions in a single question. We will solve the first…

Q: What is fire? What are the classifications of fire? Make table of the type of fire versus the type…

A:

Q: e cofactor of the el

A: To find  Cofactor of element zero

Q: What is Double-Acting Unbalanced Linear( Landing Gear). Give some application examples of it.

A: The landing gear is used in aviation structures which are used to give support to an airplane during…

Q: the speed can be positive or negative false true

A: Speed is a scalar quantity. it has no direction so, speed can be positive or zero. it cannot be…

Q: Define the following statements which is true ?

A: Given;   Water at 420 C is sprayed into a stream of air at atmospheric pressureDBT=400CWBT=200CAir…

Q: Mechanical Draft Cooling Tower  - Draw P&ID Diagram of any one process from this industry. -…

A:

Q: "hich one of the following

A: given:

Q: Define 'power'.

A: It can simply defined as the amount of work done per unit time. Or the rate of time of doing work or…

Q: ascal's law applies only to

A: given: Pascal's law applies only to

Q: Sketch the Orthographic and  auxiliary view

A:

Q: How did you combine eq1 and eq2?

A:

Q: Write a procedure to conduct hand arm vibration monitorin

A: Procedure to conduct hand-arm vibration monitoring Step 1: Gather all required equipment like:…

Q: What is the difference between modal and nonmodal G codes?

A:

Q: Explain where did 23.4 came from

A: Use linear interpolation technique to calculate saturation pressure at 20 degree Celsius.

Q: Define the following with formula and units. a) Torque b) Couple

A:

Q: Make a Drive Shaft in SINUMERIK (ste

A: A drive shaft is a vehicle shaft that transmits power from the transmission to the wheels. The…

Q: - Which of the following statements regarding a

A: Given; Choose the following statements is correct,  Where,  Rankine cycle with reheating ,

Q: pllowing: ne role of tribc ne role of tribc

A: Tribology is the study of wear, friction, and lubrication in natural and artificial systems, and it…

Q: Please help me with number 7,8,11 and 16. This is not graded

A: Solution    7. PITCH-This is the distance from a point on the screw thread to a corresponding point…

Q: British Standard code BS131 refers to

A: British standard code BS131 REFERS to Izod test.

Q: The BREAK command: a. Will work on lines and arcs b. Will work on closed objects c. Can have the…

A: BREAK Command is a tool in AutoCAD software which is used for removing part of an object, open or…

Q: Interchangeability system is also called

A: Solution:

Q: Calculate Degree of freedom for the following figures.

A: (i) Degree of freedom is calculated by using the formula DOF=3l-1-2j-h

Q: Q1.With a neat diagram ,explain about the working of Flash Type  ADC

A: Flash Type ADC is based on the principle of comparing analog input voltage with a set of…

Q: orce is an agent that destroys or tends to destroy motion. Select

A: this statement is( true)

Q: 3. Provide at least two distinctive definitions of two of the following terms:

A: Given Data : Job satisfaction leadership

Q: 1. What is your mech diameter of 3

A: given:l=35cmr=3/2cm

Q: 2) Explain what do you mean by the letter H in coding system? Explain the coding system by your own…

A: American Standard Code for Information Interexchange, ASCII is a standard that assigns letters,…

Q: Explain the symbols given below

A: There are 3 basic symbols are used for indicating surface texture on components Ans(a) Surface…

Q: answer the question below. Robotic arms can have different end effectors. An end effector is the…

A: Solution is attached below;

Q: What does a milky coloured ATF indicate

A: ATF in cars is stand for automatic transmission fluid. When a radiator fails, then the contaminated…

Q: i need (Acknowledgment for traing coop )

A: given; Acknowledgment for traing coop

Q: haft G-Codes programming process (sumerik)

A: CNC programmers increasingly face special tasks that take them to the limits of classic (DIN 66025)…

Q: Explain Miner's Rule and discuss the limitation in applying Miner's Rule.

A: The power capacity of a Gear Drive is a critical aspect in ensuring that driven equipment runs…

Q: sketch the B.M and S.F diagrams with indicating all

A:

Q: Need more information about number 34000 BTUhour and 20000 BTUhour ... both numbers are from where ?

A: Given: 34000 BTU/ hour and 20000 BTU/hour To find : How these values are arrived

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.