Given the following thread specification: ½ - 28 UNEF – 2A 1) What is the pitch? __________ 2) How many threads per inch? ________ 3) What class of fit? __________________ 4) What is the diameter? ________________ 5) Completely describe the thread form. ____________________________________

Q: Expandable pattern is used in ?

A:

Q: 71) Which is not a surface texture parameter? A) roughness B) cutting length C) array D) wavy E)…

A: As per our guideline we can answer only one question at a time ,you are requested to post other…

Q: I need answers to questions 1, 2, and 3 pertaining to the print provided.

A: There are 6 columns which are featured in the revision history block of this drawing. And that…

Q: Minimum thickness?

A: Given; A building has to be maintained at, TI=210 C (DB)Wet bulb, Tdb=10.170COutside temperature,…

Q: 25- Which one of the following operation is not a sheet-metal forming process? a) Seaming Deep…

A: It is required to determine which of the following process is not a sheet metal

Q: (4) The average flow stress is the flow stress multiplied by which of the following factors: (a) n,…

A: “Since you have asked multiple question , we will solve the first three questions for you. If you…

Q: What is the discontinuity of loading?

A: The load along the length of the structure, say a beam if is consistent then we can say that the…

Q: 4. What finish is required on the ends of the gear blank? 4. 5. What limits of flatness are given…

A: 4. What finish is required on the ends of the gear blank

Q: You are a new employee in a mpany and they asked you to do a all sketch for Acme thread if p= 10 mm…

A:

Q: v thread is:

A: In screw largest diameter is its major diameter

Q: just to clarifay is the shaft stainless steel? or the tool making the threads on the shaft

A: It is the shaft which is made up of stainless steel.

Q: To make 5 cast iron tool holder as shown in Figure 2 on a one time order, and the inside hole…

A: Die casting and forging involves huge initial machine cost , it is not recommended to go for die…

Q: In bending operation of a piece of flat metal sheet. The fina e after springback is than the angle…

A: 19.Ans:  B is correct smaller The final bend angle after springback is smaller than the angle to…

Q: 3.1 What would be the best type of jig for bending the patterns of the different sections of the…

A: given; what would be the best type of jig for bending the pattern of different section of the…

Q: Why it is important to loosen one screw before tightening the opposing one by an equal amount?

A: If there are two sequences of screws or bolts and n number of screws is to be tightened on each…

Q: 150* 6. The component above requires equally spaced slots 2-1/2" apart over a 150" span. How many…

A:

Q: sketch write short notes on any two types of rolling bearings

A:

Q: Material is forced through a die opening called Drawing Select one: OTrue O False

A: A metals working process in which the material is forced through a die such as metal, glass of the…

Q: To make 5 aluminum wheels with smooth surface and precise dimension as shown in Figure 1 for one…

A: It is given that the final product should possess smooth surface finish and precise dimension.

Q: hearing stress value will be The angle of twist will be

A: Solution:- Given data:- T =400 N-mt = 2mmG =28 Gpa Area of tube, =40×20+π×1022957.079mm2 Total…

Q: Which of the following process for sheet metal cutting, the cut piece is the desired part? Shearing…

A:

Q: 1. Uf this drawing? 2. What is the name of the company responsible for the drawing? 2. MILWAVKEE…

A: Given :-  9.The drawings are shown in what angle

Q: Describe the method of sections?

A: Method of section In this method we deal with the non-concurrent forces. Here, we get three…

Q: Match the following. Forging is an example of Choose. Choose. Drilling operation is an example of…

A: Forging is an example of     Primary shaping process

Q: H.W. N.O. 9 Fig. (C.W), represent the detail of drawing for "Knuckle Joint", the desire: A. Draw the…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: required punch diameter ?

A: Given data;   A meatal disc is to be punched having following data,i.e,  Diameter,d=30 mm…

Q: What is the mechanical advantage of a 1/4" diameter screw with 20 threads per inch?

A: Calculating the mechanical advantage of a 1/4" diameter screw with 20 threads per inch.

Q: The Sleeve Bearing Problem A machinist had pressed a new prelubricated, porous sintered bronze…

A: There may be following reasons of bearing failurePoor finishing on the bearing surface after…

Q: Hollow shape parts are made __________ process. a. Cold rolling b. Wire drawing c. Deep drawing d.…

A: Rolling process are use to produce the symmetrical objects. Wire drawing process is used to produce…

Q: Match the following. Shaping operation is an example of Bending is an example of

A: Shaping operation is an example of Answer: Primary shaping operation

Q: 18 Which of the following are types of thread-cutting dies? Multiple Answer (check all that apply) O…

A:

Q: I need answers to questions 1, 2, and 3 pertaining to the print provided. Note: A tutor keeps…

A: If any changes in the part feature are made, the changes are recorded in the specified format in the…

Q: Write TRUE is the statement/s is True. If the statement is false, identify the word/s that makes the…

A: The above question is from manufacturing engineering. The topic is of metal removal rate. There are…

Q: What firce is requure to punch off 5 mm hole out of a 4 mm thick plate if the ultimate punching…

A: Ultimate Punching Stress (Su) = 200 MPa The actual shear stress in the material is τ=F/A; Thus the…

Q: What would a .010 - .020 cutback of a 14.500 Diameter be?

A: Given, Diameter, d= 14.500 mm  Range of cutback: c~ 0.010 - 0.020

Q: N= 11 %3D Question: A circular shape blank will be cut of (100 + mm diameter from a strip of (2.8 +…

A:

Q: final thickness that can be produced by this

A: Given data;  Diameter=600 mmCoefficient of friction=0.05 Thickness=2 mmDetermine the minimum…

Q: To make 200 cast iron tool holders as shown in Figure 2 per order, two orders per year expected, and…

A: Consider the machining of harder material; this machining process induces high degree of stress and…

Q: Add the Correct Answer Calculations 1. 1/4 indicates 2. 20 indicates UN is an abbreviation for Shape…

A: Since you have asked multiple sub-parts only the first 3 subparts are solved for you, If you want…

Q: Consider following thread call-out 3/4-10 UNC-2B, what does the 2B mean? is the standard quality for…

A: 3/4 -10UNC -2B It shows that ¾  diameter unified coarse pitch of 2B class of fit screw thread.2B…

Q: estimate shaft life.

A: Given; Cylindrical shaft is subjected to an alternating stress=100 MPaFatigue strength to sustain…

Q: 1.How many assemblies are described by this one assembly drawing? 2. Each assembly described by…

A: Given questions 1. How many assemblies are described by this one assembly drawing2. Each assembly…

Q: What is the major diameter of the thread? 16mm?

A:

Q: Based on the CNC program below, identify 1)what machine it is (lathe/mill) ? 2)is the coolant…

A:

Q: A circular shape blank will be cut of (100 +) mm diameter from a strip of (2.8 + mm with a clearance…

A: LET N=11,

Q: a- Drive the mathematical equation used to find the Break- Even - Point. b- Draw the production…

A: The point at which a company's revenues equal its costs is known as the break-even point. The…

Q: Drilling operation is an example of Choose... Forging is an example of Choose...

A: The drilling and forging processes are not a surface finish, joining and secondary process.…

Q: Reduction ratio in the first and subsequent draws may not The minimum number of draws necessary will…

A:

Q: Table 1 below shows the cutting speed for some common materials and the feed rates for various…

A:

Q: (a) Design a suitable layout for manufacturing a hexagonal bolt  and state its  advantages

A: Solution:

Metrology of Screw Threads

Screw threads are a series of ridges having the profile of a helix. This helix profile runs continuously along the length of a uniform solid or a hollow bar of a circular cross-section at periodic intervals. These helix ridges are also formed over a conical bar. These continuous helical ridges are termed threads.