Given: The L8x4x½ shown below is welded to the gusset plate by its long leg. L₁ = 10" and L2 = 7.5". L₁ L2 Determine the gross area. 5.80 in² Calculate the length of the connection. 8.75 Calculate the eccentricity of the connection. 0.854 Calculate the width of the connected element. Calculate the value of the shear lag factor. Calculate the effective net area. II in² 11 11

Given: The L8x4x½ shown below is welded to the gusset plate by its long leg. L₁ = 10" and L2 = 7.5". L₁ L2 Determine the gross area. 5.80 in² Calculate the length of the connection. 8.75 Calculate the eccentricity of the connection. 0.854 Calculate the width of the connected element. Calculate the value of the shear lag factor. Calculate the effective net area. II in² 11 11

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter7: Simple Connections

Section: Chapter Questions

Problem 7.11.10P

See similar textbooks

Similar questions

A staggered riveted connection has rivets arranged as shown below. The plate is 400 mm and 12 mm thick with four bolt holes. The diameter of rivet is 34 mm The diameter of the rivet hole is assumed to be 5 mm larger than rivet diameter. Fy = 248 MPa. Fu= 410 MPa, Fv in rivets is 372 MPa. 1. Which of the following gives the distance b so that the net area in section 1 – 2 – 3 – 4 equal to the net area in section 1 – 2 – 4 a. 30.01 mm b. 25.12 mm c. 19.7 mm d. 12.23 mm 2. Which of the following gives the net area using the computed value of b. a. 4622.65 mm² b. 5623.75 mm² c. 3623.64 mm² d. 7652.85 mm² 3. Which of the following gives the maximum tensile force that the connection could carry if the allowable yield stress is Fy/1.67. a. 432.12 kN b. 724.73 kN c. 253.25 kN d. 712.81 kN 4. Which of the following gives the maximum tensile force that the…
e. Calculate "P" in KN considering failure on bearing on block shear Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm
A 100 x 100 x 10 mm angle is to be welded to a gusset plate. The angle carries a load of 200 kN applied along its centroidal axis which is 28.7 mm above the short leg as shown in the figure. Use an 8 mm fillet weld with a minimum tensile strength Fu = 483.33 MPa. Determine the length of a transverse fillet weld along the edge of the angle in order to avoid eccentricity of loading. Determine the length of side fillet weld required at the heel. Determine the length of side fillet weld required at the toe.
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0.a) Determine the design tensile strength of the section based on yielding of the gross area.b) Determine the critical net area of the connection shown.
Question-03: The steel tie bar shown in Figure 2 is to be designed to carry a tensile force of magnitude P = 30 kips whenbolted between double brackets at A and B. the bar will be fabricated from 0.6inches thick plate. Forthe grade of steel to be used, the maximum allowable stresses are: Normal stress = σn = 25 ksi, Bearingstress = σb = 55 ksi and Shearing stress = τ = 5.4ksi. Solve for the values of (a) the diameter d of thebolt, (b) the dimension b at each end of the bar and (c) the dimension h of the bar.
pls help! Write the complete solutions and legibly. Answer in 2 decimal places. UPVOTE WILL BE GIVEN! MECHANICS OF DEFORMABLE BODIES Let Q = 0 and T = 8 (Example: 12Q°C = 120°C). Just substitute the number in letter. Thank you! For the frame shown, a 4QQT-N load is acting on member ABD at D. If the allowable material shear stress for is 4Q MPa, determine the required diameter (rounded off to the nearest 2.5 mm) of the pins at C and D. Pin C and pin D are subjected to double shear and single shear, respectively. If the thickness of member BC is 12 mm and that of member DE is 16 mm, determine the maximum bearing stress at C.
Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
Prob 01: An 18” depth beam is bolted to a 24” depth girder is connected similar to that in figure shown below. Thediameter of the rivet is 20mm and the angles are each 100mm x 100mm x 12mm thick. For each bolt, assume thatthe allowable bearing stress is 220 MPa. Determine the allowable load P in KN on the connection. *show all theload P in kN for bearing stressBeam web thickness = 5mmGirder web thickness =
Instructions:-Write down each step clearly in calculation suggestion what you are doing.( you need to tell why you selected particular value ofø (phi) and U). What and why you are calculating certain step Consider R= 433.5 PROBLEM A welded tension member is consisting of two channels placed 400mm back to back with flanges turned out. Select a channel for factored tensile of 4RKN using A36 steel and AISC specifications.The member is to be 15m long. PLASE USE THE EXAMPLE AS GUIDE OF ALL STEPS AND FORMULAS TO BE USE
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0. Determine the critical net area of the connection shown. Determine the design tensile strength of the section based on yielding of the gross area.
4. The plate shown in the figure is fastened to thefixed member by seven 10-mm-diameter rivets.Compute the value of the loads P so that theaverage shearing stress in any rivet does notexceed 70 MPa.
A square hollow steel strut if thickness 10mm is pin connected to two connector plates of thickness, 12mm. The connector plates are welded to the base plate of thickness, 12mm. The base plate is fastened to te concrete base by 4-16mm diameter anchor bolts. The diameter of the pin is 16mm. Which of the following most nearly gives the shearing stress in the anchor bolts? Choices 150.00 MPa 59.68 MPa 51.69 MPa 119.37 MPa