Hi, My question was not completed at first, let me rephrase my question. The experiment in the lab was part of accurately weigh out about 0.17 to 0.20g naphthalene to 0.001g in a weighing paper. Quantitatively transfer thenaphthalene to your t-butanoland stir the mixture until a naphthalene dissolves. Question: How would the freezing point of the solution be affected if all the naphthalene were not transferred?

Hi, My question was not completed at first, let me rephrase my question. The experiment in the lab was part of accurately weigh out about 0.17 to 0.20g naphthalene to 0.001g in a weighing paper. Quantitatively transfer thenaphthalene to your t-butanoland stir the mixture until a naphthalene dissolves. Question: How would the freezing point of the solution be affected if all the naphthalene were not transferred?

Macroscale and Microscale Organic Experiments

7th Edition

ISBN:9781305577190

Author:Kenneth L. Williamson, Katherine M. Masters

Publisher:Kenneth L. Williamson, Katherine M. Masters

Chapter3: Melting Points And Boiling Points

Section: Chapter Questions

Problem 8Q

See similar textbooks

Similar questions

A student was careful to make and stir all of her standard solutions immediately before measuring their turbidity for her calibration curve. However, she let her tap water solutions sit for 10 minutes prior to measuring their turbidity. If she measured the top portion of the solution, would her experimental sulfate ion concentration be higher or lower than it should be?
B. Determining the Composition of a Mixture of Sodium Chloride and Sodium Nitrate Partner I Prepare a solution of sodium chloride + sodium nitrate and indicator. Obtain a dropper bottle of potassium chromate (indicator) solution. To a clean and dry 125 mL Erlenmeyer flask, add about 40 mL of water and 8 drops of indicator solution. Weigh out approximately 0.05 grams of sodium chloride + sodium nitrate solid and record its exact mass. Dissolve the solid in the solution from step 1, stirring with a stirring rod to ensure complete dissolution. Determine and record the total mass of the Erlenmeyer flask and solution, noting the balance that you use to weigh. Rather than measuring the volume of silver nitrate solution added as in Part A, we will measure the mass of titrant added and make use of the weight-percentage concentration of silver nitrate in calculations. Prepare the silver nitrate solution. Obtain about 15 mL of 1.70% w/w silver nitrate solution in a 50 mL beaker. Designate a…
In the second and third parts of the freezing point depression lab, a solute is added to the test tube containing the solvent by pouring it in from a folded piece of weighing paper. If some of the solute is lost between the weighing and the transfer into the solvent, what effect would this have on your experimental molar mass? Explain your answer.
Which of the following is true when preparing solutions? a. Make sure that the solvent and reagents are contaminated. b. When diluting to the mark using a volumetric flask, the upper meniscus and mark should be at eye level. c. If amount added is over the mark, you cannot just take out the excess liquid and preparation must be repeated. d. After mixing the contents of the flask and the level of the meniscus seems lower than the mark, add more diluent.
Please complete the data. PLEASE SHOW HOW DID YOU GET THE DATA. Step by step solution please. For table 1 and 2, please show the step by step solution. You may just fill in the first trials.
Please determine how to make a working standard Solution of about 0.010mg/mL. Caffeine will be the active. Diluent will be water.
Compute for the needed values for slution preparation: 1. Prepare the following solution quantitatively using boiled distilled water per group:250.0 mL 0.0500 M standard HCl solution from 1.0 M HCl 2. a. 500.0 mL 0.1000 M stock EDTA solutionb. 100.0 mL 0.0500 M stock Ca2+ solution
CREATE A SCHEMATIC DIAGRAM FOR THIS PROCEDURE: C. Preparation and storage of standard solutions 1. Use the weighed and transferred NaCl powder in procedure B. Dissolve it in about 10 mL distilled water. Use a stirring rod to gently stir the solution until it has been dissolved to an extent. Make sure you will not incur any noise while stirring. 2. When the NaCl powder is partially dissolved, transfer the resulting solution into a 100 mL volumetric flask. Use a stirring rod and funnel. 3. Repeat steps 1 and 2 until no NaCl remains in the beaker and until you are almost at the mark of the volumetric flask. 4. Rinse the last portion of the solution from the stirring rod into the volumetric flask with a stream of water from the wash bottle. Rinse the funnel and remove it. Dilute the solution in the flask using a Pasteur pipette until the bottom of the meniscus is even with the graduation mark. 5. Put a stopper on the volumetric flask. Invert the glassware up and down around five…
What would be the concentration in ppm of the final solution made by mixing 200. mg of ethanol into 2.5 kg of water? Report your answer in standard notation and do not include units.
( give step by step handwritten solution , these are subpaert do all with detail explanation )
Please write the mass balance for the solution below:
In the procedure you followed for the above experiment, the pipet that was used to measure the unknown acid was not clean, and some of the unknown acid remained above that left in the tip. Will the calculated molarity of the unknown acid be erroneously high, low, or not affected?