Identify and explain the safety procedures and precautions when working with tools and equipment's that should be followed during the installation of the cables?
Q: In terminating the coaxial cable, if the present procedure is to cut part of the braided shield and…
A: In this question we need to find what is the next procedure is to
Q: What NEC chapter contains tables that are used to determine the proper size of a conductor?
A: The NEC is the worldwide accepted code for electrical wiring and installation. To determine the…
Q: Explain the major consideration required for a protective system.
A: In the power plant, the generator is one of the most expensive pieces of equipment; therefore,…
Q: Why is bonding of the conduit necessary when using reducing bushings to properly match a conduit to…
A: In such situations, conduit bonding is done to prevent or mitigate shock hazard as it provides a low…
Q: Why is it important, when soldering connectors onto a piece of electronic circuitry, to leave no…
A: Given: Soldering of connectors
Q: Does the NEC make suggestions about how to wire a house that will be occupied by handicapped…
A: The NEC is the electrical code that is accepted by everyone belongs to the electrical industry. NEC…
Q: Identify and describe the step-by-step process used to pull cable and also describe the step-by-step…
A: According to the question we have to Identify and describe the step-by-step process used to pull…
Q: 2. What fault occurs when Line and Neutral wires come with each other? Which device is actuated?
A: According to the given question, it is required to describe the fault which occurs when a line and a…
Q: Discuss application and uses of earth leakage breaker ?
A: ELCB (Earth Leakage Circuit Breaker):- An ELCB (Earth Leakage Circuit Breaker) is an electrical…
Q: when installing coaxial cable the minimum bending radius generally recommended is
A: Coaxial cable: It is an electrical cable. It consists of an inner conductor along with a concentric…
Q: Q.1: Non-metallic conduit must not be installed where extremes of ambient temperature, why?
A: Since you have asked multiple questions, we will solve the first question for you. If you want any…
Q: What type of conduit that should be used where corrosion is a factor?
A:
Q: What device can determine how far a cable damage is?
A: we have to give detail about the device that can determine "how far a cable damage is".
Q: What is the minimum branch circuit wire size that may be installed in a dwelling?
A: Basically, the 14 AWG wiring is used for typical lightening loads in the residence.
Q: Table 314.16(A) of the Code shows the maximum number of conductors permitted in a given size box. In…
A: When setting a job, an electrician often makes a circuit, thinking of the best way to use wires…
Q: 1. Identify and describe the step-by-step process used to pull cable and also describe the…
A: The step-by-step process used to pull cable STEP 1: Check the Cable Width and Pipeline to make sure…
Q: What is the name of the gadget that can determine the distance between a cable's damage and where it…
A: Name of the gadget which is used for finding the cable damage and its location is "Cable Fault…
Q: What kind of instrument is capable of determining the distance to the place of cable damage?
A: The explanation is as follows.
Q: Identify and explain the safety procedures and precautions that should be followed for fire…
A: Procedure that is used to install cable in buildings are as follows:- Electrical conduction for…
Q: 8. What are the common protective links for electrical control lines and what electrical components…
A: Various protective devices or links are used in the electrical control line of the power system.…
Q: How can you calculate the maximum short-circuit current that can pass when the A-B ends of an outlet…
A: The detailed answer is solved below according to the given parameters and instructions in the…
Q: Why is the Insulating plastic of wires color-coded?
A: Wire A wire is a thin, malleable metal strand. The most common way to make wire is to draw the metal…
Q: when the insulation of the equipment tested healthy ? justify .
A: As we know that the current sent through a conductive wire to the destination means to the consumer…
Q: Explain the two main testing process used in testing transmission cables.
A: Fiber optics is a technology that is connected with the transmission of information as light rays…
Q: Identify and describe the step-by-step process used to pull cable and also describe the step-by-step…
A: According to question we have to Identify and describe the step-by-step process used to pull cable…
Q: 45. What section of the Code prohibits the use of sheet metal screws as a means of attaching…
A: As per the bartleby policy you can ask one question at a time so please ask other questions a…
Q: Question#03: Justify: why electrical isolation and theft prevention are the advantages of…
A: 1. The main benefits of non-conductive cable are its isolation from the rest of the system and its…
Q: In terminating the coaxial cable, If the present procedure is to loosen up the braided shield and…
A: In terminating the coaxial cable, the the flaring and bending back the outer braid onto the cable…
Q: Identify and describe the step-by-step process used to install cable in the any building?
A: Step by step process to install cable in any buildings: step 1: In the slab, a PVC conduit is laid…
Q: What is the type,application and rating of cables?
A: Types of cable are classified according to their Voltage level .
Q: 4.Justify: why electrical isolation and theft prevention are the advantages of non-conductive cable?
A: According to the given question, it is required to determine the reason why non-conductive cables…
Q: Identify and describe the step-by-step procedure that is used to draw cable, as well as the…
A: It is asked to describe the step-by-step procedure that is used to draw cable and to install cable…
Q: Identify and describe the step-by-step process used to pull cable and also describe the step-by-step…
A: The step-by-step process used to install cable in buildings are as follows:
Q: In what ways may the Instrusion detection and prevention system be used to reduce the hazards of…
A: Intrusion detection and prevention system is used as no one can enter our system with malicious…
Q: Identify and describe the step-by-step process used to pull cable and the step-by-step process used…
A: 1. The first step is to to lay electrical conduction of 2mm thick and 25 mm in size for the PVC…
Q: Justify: why electrical isolation and theft prevention are the advantages of non-conductive cable?
A: The main advantages of non conductive cable is it's isolation from the rest and most of the…
Q: Airframe Electrical What is the purpose of the inspection hole on a connector contact?
A: There are different kind of connectors. Crimped contacts are mostly used connectors.Connectors are…
Q: What do you mean by permissible current loading of an underground cable?
A: Permissible current loading: It is the maximum amount of current the cable can carry without any…
Q: Airframe Electrical How much of the conductor should be exposed past the end of properly crimped…
A: Crimped contact is used to provide maximum reliability and safety to electrical equipment.There are…
Q: Is it okay to use a cable tray for the horizontal path of telephone lines to their specific outlets?…
A: EMT conduit size (inch) Number of cable 1 4 1-1/4 6 1-1/2 8 2 14 2-1/2 17
Q: Describe the various methods of laying underground cables. What are the relative advantages and…
A: Proper laying and attachment of fittings decide the reliability of underground cables. The fittings…
Q: draw a pictorial/wiring diagram of the jumpers connected to the front panel of a computer system…
A: The Front Panel Connections, also known as the Front Panel Header or FPanel, are a collection of…
Q: Why is it critical to keep cable clutter to a minimum in a rack?
A: It is asked to explain why it is critical to keep cable clutter to a minimum in a rack.
Step by step
Solved in 2 steps
- Identify and explain the safety procedures and precautions when working with tools and equipments that should be followed during the installation of the cables? Note: Please do not handwrittenWhich section of the Code prohibits supporting coaxial cables from raceways that contain light or power conductors? NEC ______________Identify and explain the safety procedures and precautions that should be followed for fire prevention and safety during the installation of the cables? Note: Please do not handwriting
- 4 Describe the various methods of laying underground cables. What are the relative advantages anddisadvantages of each method?What section of the Code prohibits supporting fire alarm conductors from raceways that contain light or power conductors? NEC ______.How can you identify and replace faulty network cables?
- Identify the type of cable that is permitted in single- and multifamily dwelling units but that cannot be used underground, nor in buildings that are more than three stories above grade, nor in commercial garages, motion picture studios, theaters, places of assembly, elevator hoist ways, and other corrosive or hazardous locations, and what electrical code is universally used in the United States?Identify and describe the step-by-step process used to pull cable and the step-by-step process used to install cable in buildings.Which of the following must be notified prior to equipment shutdown for repair? a. Director of facilities b. Electrical department c. Affected employees d. Environmental, Health and Safety Office
- QUESTION 1 Where Type NM cables pass through cut or drilled slots or holes in metal members, the cable shall be protected by _____ which are installed in the opening prior to the installation of the cable and which securely cover all metal edges. a. plates b. listed grommets c. listed bushings d. a or ba. Is it permissible to install low-voltage Class 2 systems in the same raceway or enclosure with light and proper wiring? ______ b. Which Code section covers this? ______1. Identify and describe the step-by-step process used to pull cable and also describe the step-by-step process used to install cable in buildings? Note: Please do not handwritten.