Start your trial now! First week only $4.99!*arrow_forward*

Question

If 50 Hz input ac signal is applied at the input of a full wave rectifier, then what will be the output frequency?

Tagged in

Engineering

Electrical Engineering

Find answers to questions asked by students like you.

Q: Question:1 A diode whose internal resistance (forward biased) is 20 2 is to supply power to a 1000 2...

A: NOTE: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the questio...

Q: Question:5 The full wave rectifier with filter is given, calculate: Do Filtered output V. "Drip-p) R...

A: The peak to peak ripple voltage is the difference between the maximum voltage and the minimum voltag...

Q: In the circuit given below, V = 174 V. The variable resistor is adjusted until it absorbs maximum po...

A: As per maximum power transfer theorem, maximum power absorbed by load resistor if the load resistanc...

Q: Please provide long discriptive answer on given topic. Topic : single phase half controlled rectifie...

A: Single-phase half controlled rectifier fed DC series motor:- Single-phase controlled Rectifier Contr...

Q: I did not know that I need to ask them in different question, sorry for that. I have a and b parts t...

A: Given: The ratings of each element are as follows: Generator-4.16 MVA, 2.4 kV, 1000 A.Transformer T1...

Q: Although current is blocked in reverse bias, (a) there is some current due to majority carriers (b) ...

A: When a pn junction diode is reverse biased, then the height of the junction potential barrier increa...

Q: a) Determine the number of mesh-current equations needed to solve the circuit shown. 4.8 b) Use the ...

A: Given circuit,

Q: A hydro-electric station has an average available head of 100 meters and reservoir capacityof 50 mil...

A: Given: The values are shown as: Head,h =100 m,Capacity, Q= 50×106 cubic meter,Hydraulic efficiency...

Q: he network in the Figure below operates at 60 Hz. Compute the energy stored in the mutually coupled ...

A: Click to see the answer

Q: 4. Find vg, v10, i4, V4, Vx, iz and i (in the given order) in the circuit below. (Hint: Use KVL, KCL...

A: Write the given values in the circuit diagram. vs=60 Vi8=5 A

Q: What is energy efficient induction motor and conventional indcuction motor?

A: Now a days, the demand of electricity is increasing day by day which requires additional power. Due ...

Q: Identify the contents of the registers, memory location (C070H), and the flags as the following inst...

A: Given: M=C070 H Now solve the problem: LXI H, 2020H : (load register pair immediately) After executi...

Q: To get the maximum electric current output from the PV module the most appropriate distance between ...

A: The power generated by the solar cell depends on the light intensity As the source is moving away f...

Q: 4.12 Use the mesh-current method to find the power dissipated in the 1 N resistor in the cir- cuit s...

A: Click to see the answer

Q: I need to answer of this Control System Question

A: Click to see the answer

Q: What will be the radiation resistance of a dipole antenna whose effective length is equal to a quart...

A: Given information: The effective length of the dipole antenna is equal to a quarter of a wavelength ...

Q: I just need help with part c.

A: Applying KCL in the following circuit for t>0 Let v is the voltage across all elements in parall...

Q: Discuss power equation of synchronous motor.

A: Click to see the answer

Q: a sine wave has a maximum value of 230 v. what is the voltage after 38° of rotation

A: Click to see the answer

Q: • Solve for the value of constant(C) by obtaining the orthogonal trajectory of the given equation be...

A: Click to see the answer

Q: Design any 2 bit ADC which performs the analog to digital conversion directly by utilizing the inter...

A: An Analog to Digital converter performs conversion of analog signal into corresponding digital signa...

Q: The majority carriers in an n-type semiconductor are (a) holes (b) valence electrons (c) conduction ...

A: Extrinsic semiconductors can be classified into two categories: 1. n-type semiconductors 2. p-type s...

Q: Question 2: Common Base For the amplifier circuit in Figure Q.1, the transistor parameters are Ica= ...

A: Click to see the answer

Q: Radium decomposes at a rate proportional to the amount present. If half of the original amount disap...

A: Click to see the answer

Q: The charge entering a certain element is shown in the given figure, where A = 70. Find the current a...

A: given: A = 70 Since it is known that current is given as: i=dqdtor,i=slop of the qt vs t graph So th...

Q: Subject- Rotating AC Machines. Explain in detail, Synchronous motor as a synchronous condenser.

A: A synchronous motor when over excited can supply reactive power to the system. Sometimes synchronous...

Q: R1 is connected in series with R2 and R3. R2 and R3 are in parallel. what is the value of current fl...

A: For this problem, we have to use two formulas. One is ohms law I=V/R, another one is current divisi...

Q: The thermal voltage for a on junction diode is 350 mv. What will be temperature in centigrade?

A: Given thermal voltage VT = 350 mv = 0.35 volt To find temperature in centigrade

Q: Determine IB RC 100 Ω RB + Vcc 10 V 10 kΩ VBB 5 V

A: Click to see the answer

Q: a) If ig = 0.5 A and G = the power delivered by the current source. b) If vg conductor is 9 W, find ...

A: Here the circuit is simple series circuit. Here the voltage and current follow simple ohm's law equa...

Q: 4- If we have a signal f(t) passing through a system with impulse response g(t), the output is (b) g...

A: Convert the functions in the Laplace transform, and find the output. f(t)→LFsg(t)→LGsYs=FsGs

Q: Obtain the waveform of output states Q and ̅for the SR when the input condition as in figure 5 is gi...

A: Note : In the question it given SR but in figure it is given JK flipflop so assuming the JK for writ...

Q: Example 3.1: Calculate the node voltages in the circuit shown below. 5 A 4Ω 1 6 Q (A) 10 A

A: To find the node voltages at 1 and 2 Let the voltage at node 1 be V1 and voltage at node 2 be V2.

Q: Textbook Problem

A: Given: The values are shown below:

Q: This question from Measurements instrumentation course

A: Non linearity is define as the time or situation at which particular device or element does not meet...